Advertisement
4) Remove the liner from its packaging and place it back side down on the floor or countertop in front of the wall where
it will hang.
5) Remove the nuts retaining the safety straps on the inside ends of the liner shell. Pull the safety straps off of the studs
to disengage. Separate the lower filter/control section from the liner shell by pulling them apart. These sections only are
held together by snaps once the safety straps are disengaged. Disconnect the electrical power cord from the reverse
side of the filter/control section. Set the filter/control section aside.
Warning: Make sure power is off and locked at the service disconnecting
6) Liner shells are shipped from the factory with the junction box mounted for the M1200 double blower configuration.
Remove the junction box cover. If the M600 single blower will be used, relocate the junction box and ground strap to
the offset location. Install an appropriate 1/2" UL listed electrical wire clamp through the electrical opening on top of
the liner shell. Install electrical wiring from the service panel to the liner location. Consult the connection diagrams
(on previous page) for further details on electrical placement.
Model
M600 Single
M1200 Dual
* Add 0.5 amp for each halogen light. 2 lights: 30" - 41", 3 lights: 42" - 53", 4 lights: 54"-66"
7) For M600 single blower installation, skip to Step 8. Install the 10" transition (VP566, included) to the top of the liner
shell with the screws provided. Seal the base of the transition to the hood with duct tape.
8) Extend wires to the liner shell and insert them into the electrical wire clamp on the junction box. Tighten the wire clamp.
From inside the liner, using UL listed wire nuts, attach the "neutral" wire to the white lead, the "hot" wire to the black
lead, and the ground wire to the green lead inside the junction box. Replace the junction box cover.
Warning: Do not operate hood without proper ground connection.
9) Taped inside the liner behind the filters is a drill template/spacing tool. This tool will be used to locate the pilot mounting
holes for the four corners of the liner shell and set the spacing between the bottom of the liner shell and the bottom
of the decorative enclosure.
Ready a power drill with a 3/32" drill bit to have within reach while working inside of the decorative enclosure. Hold
the template with the long side standing up and the short side pointing left. Place the long side of the template against
the inside of the left end of the enclosure. Slide the template up until the short side of the template rests against the
bottom of the enclosure. Now slide the template along the bottom of the enclosure until the edge of the template rests
against the back of the enclosure. The hole in the template is now in the location of the back left liner shell mounting
screw. Drill a shallow pilot hole taking care not to drill through the decorative enclosure.
Slide the template along the bottom of the enclosure until the edge of the template rests against the front of the
enclosure. The hole in the template is now in the location of the front left liner shell mounting screw. Drill a shallow
pilot hole and repeat for the front and rear mounting holes on the right end of the decorative enclosure.
10) While guiding the wires, lift the liner shell into the enclosure about 1-1/2" up from the bottom edge of the decorative
enclosure taking care to properly align the duct connection (M1200 blower). Wood strips may be necessary to fill any
gaps between the opening and the liner if the opening in the surround is larger than the liner. Loosely install a wood
screw (included) into the four slotted corner holes along the bottom edge of the liner shell.
11) Hold the template with the short side standing up and the long side pointing left. Place the short side of the template
against the inside of the left end of the enclosure. Move the shell liner up or down in the slotted holes until the bottom
of the shell liner is flush with the top of the short side of the spacing tool. Move the tool to all four bottom corners of
the enclosure and adjust the shell liner position until the spacing tool fits properly all around. Tighten the four corner
screws.
L154 0311A
Installation Details Continued
means on the service panel during installation.
Volts
Amps*
Hz
115
5.0
60
115
10.0
60
CFM
CFM
CFM
SP@0.0"
SP@0.1"
SP@0.25"
630
625
615
1035
1015
1000
Page 4
CFM
CFM
Minimum Round
SP@0.5"
SP@0.75"
600
580
955
915
Duct Size
6" (28 in.
)
2
10" (79 in.
)
2
Advertisement
