Honeywell MX7 Reference Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Handhelds
  5. MX7 Tecton
  6. Reference manual
Honeywell MX7 Reference Manual

Honeywell MX7 Reference Manual

Hide thumbs Also See for MX7:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Reference Manual, User Manual
MX7
Hand-Held Computer
Microsoft® Windows® CE 5 Operating System
Cradle Reference Guide

Advertisement

Table of Contents
loading

Related Manuals for Honeywell MX7

Summary of Contents for Honeywell MX7

  • Page 1 Hand-Held Computer Microsoft® Windows® CE 5 Operating System Cradle Reference Guide...

  • Page 2: Limited Warranty

    Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.

  • Page 3: Vehicle Power Supply Connection Safety Statement

    Vehicle Power Supply Connection Safety Statement Vehicle Power Supply Connection: If the supply connection is made directly to the battery, a ten A slow-blow fuse should be installed in the positive lead within 5 inches (12.7 cm.) of the battery positive (+) terminal. (US) Raccordement de l’alimentation du véhicule Si l’alimentation est raccordée directement à...

  • Page 5: Table Of Contents

    Quick Start - Desktop Cradle Battery Charging in a Desktop Cradle Components Front Back Desktop Mounting Footprint Install / Remove MX7 Docking Bay Adapter Cup Install Remove 2-14 Tethered Scanners and the MX7 Cradles Assemble/Attach the AC Power Adapter Connect Input/Output Cables...
  • Page 6 Unpacking Your Passive Vehicle Mount Cradle Overview Preparing the Passive Vehicle Cradle for Use Quick Start Components Passive Vehicle Mount Cradle and U-Bracket, Assembled U-Bracket Footprint Passive Cradle and RAM Ball and Arm, Assembled RAM Assembly Components RAM Assembly Footprint Install the Cradle U-Bracket Install the RAM Bracket Cleaning...
  • Page 7 Maintenance - Vehicle Mounted Devices 4-23 Cleaning 4-23 Specifications 4-23 MX7 Powered Vehicle Cradle 4-23 Vehicle Cradle Port Pinout 4-24 MX7 Desktop and Vehicle Cradle Serial Port 4-24 Power Connector Port 4-25 Cradle Power Connector Port Pinout 4-25 Chapter 5: Technical Assistance...

  • Page 9: Chapter 1: Introduction

    Chapter 1: Introduction The MX7 is a rugged, portable, hand-held computer with a Microsoft® Windows® CE 5 operating system. There are three optional cradles available for the MX7: desktop cradle that secures the MX7, recharges batteries and enables communications between the MX7 and another device.

  • Page 11: Chapter 2: Desktop Cradle

    MX7 keypad data entries can be mixed with cradle-tethered scanner bar code data entries while the MX7 is in a powered cradle. Bluetooth device connection and use, while the MX7 is docked, are managed by the MX7 Bluetooth program, not the cradle.

  • Page 12: Preparing The Cradle For Use

    The MX7 must have a main battery installed when it is docked in a cradle. The main battery in the MX7 is recharged when the MX7 is docked in a powered desktop cradle and when it is docked in a powered vehicle cradle.

  • Page 13: Components

    Components Front 1. Charging Pocket Adapter Cup 2. MX7 Docked LED 3. Serial Interface Connector 4. Spare Battery LED 5. I/O Connector 6. Table Mounting Hole Guides...

  • Page 14: Back

    Back 1. Charging Pocket Adapter Cup 2. Cradle Connector 3. Spare Battery Charging Bay 4. Power Connector...
  • Page 15 Power Supply Connector Spare Battery Charging Bay Spare Battery Charging Terminals Spare Battery Latch Spare Battery Table Mounting Holes Cradle Connector Docking Bay Adapter Cup Docking Bay Adapter Cup Mounting Hole 10 Desktop Cradle Label 11 Serial Interface Connector 12 I/O Connector...

  • Page 16: Desktop Mounting Footprint

    2 Table Mounting Hole Guides 3 Back Bolts, washers, screws, screwdriver or wrench needed when attaching the MX7 desktop cradle to a protected flat surface are not supplied by Honeywell. Periodically check the table mounting hardware and re-tighten if necessary. Table mounting hardware can be finger-tightened.

  • Page 17: Install / Remove Mx7 Docking Bay Adapter Cup

    Install The adapter cup is installed facing in one direction. Put the adapter cup in the MX7 docking bay, aligning the screw hole in the adapter cup with the screw hole in the MX7 docking bay.

  • Page 18: Tethered Scanners And The Mx7 Cradles

    RS232 data stream may be used. It sends the data to the MX7 in ASCII format. Tethered scanners send scanned data to the MX7 when the MX7 is in a powered cradle and the scanners are connected to the Serial Interface port on the cradle.

  • Page 19: Assemble/Attach The Ac Power Adapter

    Assemble/Attach the AC Power Adapter Note: Connect the cable to the cradle first, then to an AC source. The external Power Supply for the cradle is shipped with the cradle. Contact Technical Assistance if there is no AC cable. The Power connector is located on the back of the cradle. Plug the AC power plug into any AC wall outlet with a dependable power source.

  • Page 20: Connect Input/Output Cables

    Squeeze the clips next to the connector attached to the cable to open the catches in the connector assembly. Firmly press the cable end (female) into the MX7 I/O Port connector (male) on the front of the cradle. Release the clips in the connector cable.

  • Page 21: Pinout - Rs232 Connector

    Pinout - RS232 Connector Note: Tethered scanners must be connected to powered cradles. The connector is industry-standard RS232 and is a PC/AT standard 9-pin D male connector. Pin Signal Description Data Carrier Detect Received Data – Input Transmitted Data – Output Data Terminal Ready Signal/Power Ground Data Set Ready...

  • Page 22: Cradle Leds

    Yellow / Amber Battery pack temperature out of range Flashing Red Battery pack fault or failure Note: The cradle must be connected to AC power. Spare battery charging does not require an MX7 be docked in the docking bay. 2-12...

  • Page 23: Mx7 Mobile Device System Status Led

    Cup. When the MX7 is in Suspend Mode it wakes up when it is docked in a powered cradle. There is no change in mode state settings or behavior when the MX7 is docked in a cradle without a power source.

  • Page 24: Insert / Remove A Spare Battery

    Serial port and drawing power from the cradle, is used. The spare battery well is molded in the shape of the MX7 main battery. The spare battery can be inserted in the battery well in only one direction.

  • Page 25: Mx7 Desktop Cradle Help

    MX7 Desktop Cradle Help The following is intended as an aid in determining whether the MX7 battery pack or the cradle battery charger may be malfunctioning. Problem Cause Solution Check if the battery pack is Honeywell part number MX7A380BATT / MX7392BATT or a Low Temperature...

  • Page 26: Maintenance

    Do not use paper towels or harsh-chemical-based cleaning fluids since they may result in damage to the surfaces and/or battery charging terminals (pins). Use a clean soft cloth to wipe any dirt, moisture or grease from the MX7, spare battery packs, charging contacts (pins) or the cradle.

  • Page 27: Technical Specifications - Desktop Cradle

    Technical Specifications – Desktop Cradle Note: Do not store MX7 batteries above 140°F (60°C) for extended periods. Weight 18 oz / 500 grams Dimensions H 3.5 in x W 4.25 in x L 7.5 in Temperature Operating 32° F to 104° F / 0° C to 40° C (charger On, no charging in progress) Charging 50°...
  • Page 28 2-18...

  • Page 29: Chapter 3: Passive Vehicle Mount Cradle

    Wireless communication is available as long as the mobile device has sufficient energy in the main battery pack and a clear signal path. The passive vehicle cradle is lined with strips of hook-and-loop fabric to ensure a snug fit between the MX7 and the inside of the cradle.

  • Page 30: Preparing The Passive Vehicle Cradle For Use

    Can be easily accessed by a user seated in the driver's seat while the vehicle is not in operation. Quick Start The following list outlines, in a general way, the process to follow when preparing the MX7 passive vehicle cradle for use. Refer to the following sections in this document for more details.

  • Page 31: Components

    Components Note: Bolts, washers, and wrench needed when attaching the MX7 to the vehicle are not supplied by Honeywell. Passive Vehicle Mount Cradle and U-Bracket, Assembled Note: Honeywell does not supply the bolts or washers needed when mounting the cradle assembly to the vehicle chassis.

  • Page 32: Passive Cradle And Ram Ball And Arm, Assembled

    Passive Cradle and RAM Ball and Arm, Assembled Note: Honeywell does not supply the bolts or washers needed when mounting the cradle assembly to the vehicle chassis. Use bolts with a maximum 10/32” (0.3125) diameter. See Also: "Components" RAM Assembly Components Mount the cradle U-bracket to the upper RAM ball assembly with the bolts, washers and nuts supplied by Honeywell.

  • Page 33: Install The Cradle U-Bracket

    Install the Cradle U-Bracket Note: Honeywell does not supply the bolts or washers needed when mounting the cradle assembly to the vehicle chassis. Use bolts with a maximum 10/32” (0.3125) diameter. See Also: "Components" Attach the U-Bracket to the vehicle, making sure it does not impede safe operation of the vehicle.

  • Page 34: Install The Ram Bracket

    Install the RAM Bracket 1. MX7 2. Angle Adjust Knobs 3. Passive Cradle 4. U-Bracket 5. Mounting Hex Bolt 6. Upper RAM Ball Assembly 7. Arm 8. Thumbscrew 9. Lower RAM Ball Assembly...

  • Page 35: Cleaning

    Use a clean soft cloth to wipe any dirt, moisture or grease from the MX7, charging contacts or the passive cradle. Do not use any liquid to clean the cradle. Spray or dampen the cleaning cloth with the liquid/spray. If possible, clean only those areas...

  • Page 37: Chapter 4: Powered Vehicle Mount Cradle

    There must be enough clearance at the back of the cradle to accept an MX7 with a trigger handle. There must be at least 2” clearance at the back of the vehicle cradle for power, serial interface and the MX7 Input/Output cables.

  • Page 38: Components

    Components Before installation begins, verify you have the applicable vehicle mounting bracket assembly components necessary for your mount type. Front 1 Retainer 2 Retainer Springs 3 Handle Opening 4 Vehicle Cradle Adapter Cup 5 Charging Pocket 6 MX7 Docked LED...

  • Page 39: Back

    Back 1 Retainer 2 Retainer Springs 3 Handle Opening RAM Bracket Mounting Locations 5 Strain Relief Cable Clamps 6 Serial Interface Port 7 Power Connector 8 MX7 I/O Port...

  • Page 40: Install / Remove Vehicle Cradle Adapter Cup And Top Adapter

    The vehicle cradle is shipped with the cradle Adapter Cup and Retainer Insert pre-installed. The MX7 cradle charging pocket, without a cradle adapter cup and top adapter, is designed for an MX7 with a rubber boot (MX7490BOOT or MX7491BOOT) enclosing/protecting the MX7.

  • Page 41: Install Adapter Assembly

    Install Adapter Assembly Charging Pocket Adapter Cup The adapter cup is installed facing in one direction. 1. Slip the adapter cup into the cradle charging pocket, aligning the screw hole in the adapter cup with the screw hole in the charging bay.
  • Page 42 1. The Retainer Insert back tab slides into the slot at the back of the Retainer. 1. The Retainer Insert is fastened to the Retainer cap using screws and the pre-drilled holes in the angled tabs (one on each side). 2.

  • Page 43: Remove Adapter Assembly

    Remove Adapter Assembly 1. Remove the adapter cup by unscrewing the single captive screw at the front of the adapter cup. 2. Remove the Retainer Cap Insert by unscrewing the two screws holding it to the Retainer. Slide the tab out of the slot in the back of the Retainer assembly.

  • Page 44: Ram Bracket Mounting

    The figure shown below is an example only. RAM ball mounting screws are included in the mounting kit. Contact Technical Assistance for the MX7 RAM Mount Kit for the vehicle cradle. RAM Bracket Mounting Points 1 Trigger Handle opening...

  • Page 45: Vehicle Cradle Ram Ball Assembly

    Vehicle Cradle RAM Ball Assembly 1. Fasten the RAM ball with the circular mounting base (shown in the middle in above photo) to the vehicle. 2. Fasten the RAM ball with the rectangular mounting base (shown on the right in above photo) to the back of the vehicle cradle .

  • Page 46: Ram Circular Base Footprint

    RAM Circular Base Footprint Not To Scale Bolts, washers and nuts for mounting the RAM ball to the vehicle are supplied by Honeywell. Qty 4 – Hex Cap 1/4-20 x 3/4 bolts Qty 4 – 1/4 flat washer Qty 4 – 1/4-20 nylon insert lock nuts Note: Mount to the most rigid surface available.

  • Page 47: Dc To Dc Power Supply Installation

    9000302PWRSPLY – Power Supply, 60-110VDC with cable Connecting Electrical Cables to Power Sources The DC to DC power supply is used to provide vehicle power to the MX7 when placed in a DC powered vehicle dock. Specifications for Electrical Supply Input Voltage Always observe input voltage range specified on the DC to DC power supply.

  • Page 48: Wiring Schematic

    How To Connect Vehicle Electrical Connection 1. The vehicle cradle must be empty. 2. Begin by connecting the power cable to the MX7's vehicle cradle. Work from this connection with the last connection being to the vehicle’s power source. 3. Route the cable from the cradle to the DC to DC converter.
  • Page 49 10. Wire colors depend on the type of device attached. Please refer to this illustration for wire colors. 11. Use the looms and wire ties to secure all wiring as shown above, then reattach the cover with the screws. 12. Connect the DC to DC converter to the vehicle’s electrical system. 13.

  • Page 50: Vehicle 12V Bare Wire Adapter

    Vehicle 12V Bare Wire Adapter Part Number: 9000A079CBL12ML3 Caution: For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. This fused circuit requires a ten Amp maximum time delay (slow blow) high interrupting rating fuse. If the supply connection is made directly to the battery, the fuse should be installed in the positive lead within 5 inches of the battery positive (+) terminal.

  • Page 51: Connecting The Power Cable To The Vehicle

    How To: Connect Vehicle 12 VDC Connection 1. The power cable must be UNPLUGGED from the MX7 vehicle cradle. 2. While observing the fuse requirements specified above, connect the power cable as close as possible to the actual battery terminals of the vehicle.
  • Page 52 4. Provide mechanical support for the cable by securing it to the vehicle structure at approximately one foot intervals, taking care not to over tighten and pinch conductors or penetrate outer cable jacket. 5. Refer to the following sections to complete the power connection to the MX7 vehicle cradle. 4-16...

  • Page 53: Connect Power Supply To Vehicle Cradle

    Secure the cable to the cradle with the strain relief cable clamp (see section titled Vehicle Cradle Strain Relief Cable Clamp). The power LED on the MX7 illuminates when it is receiving external power and the MX7 is docked. Cradle Power Connector Port Note: When an external power supply is used to power this cradle, the external power supply should be UL Listed, with LPS or Class 2 outputs rated 12V, minimum 2 Amps.

  • Page 54: I/O Port

    I/O Port Squeeze the clips next to the connector attached to the I/O cable to open the catches in the connector assembly. Firmly press the cable end (female) into the I/O Port connector (male) at the back of the cradle. Release the clips in the connector cable. Test the connection for stability.

  • Page 55: Vehicle Cradle Strain Relief Cable Clamp

    Vehicle Cradle Strain Relief Cable Clamp Equipment Required: Phillips screwdriver (not supplied by Honeywell) There are three strain relief cable clamps secured to the back of the vehicle cradle, located above the ports for the Serial Interface, Power and MX7 I/O connections.

  • Page 56: Vehicle Cradle Led

    The cradle LED is located at the front center of the cradle. When Cradle LED is … It means …. MX7 is docked. Cradle does not have power.MX7 is not docked. Cradle may have power. Check the power connector at the back of the cradle.

  • Page 57: Dock Mx7 In Cradle

    Do not put the MX7 into the vehicle cradle until the cradle is securely fastened to the vehicle. The MX7 is inserted into the cradle by pressing the base of the MX7 down into the cradle pocket until the connector at the base of the MX7 clicks into place with the charging connector at the bottom of the docking well.

  • Page 58: Remove Mx7 From The Vehicle Cradle

    Remove MX7 from the Vehicle Cradle The MX7 is removed from the vehicle cradle by pushing the front of the Retainer up and back until the MX7 is released from the Retainer latches and the charging pocket swings forward. Pull the MX7 up and out of the vehicle cradle pocket, disconnecting the MX7 from the charge/communication port at the base of the docking bay.

  • Page 59: Maintenance - Vehicle Mounted Devices

    Use a clean soft cloth to wipe any dirt, moisture or grease from the MX7, charging contacts or the vehicle mounted cradle. Do not use any liquid to clean the cradle, battery pack, MX7, or charging terminals (pins). Spray or dampen the cleaning cloth with a cleaning liquid.

  • Page 60: Vehicle Cradle Port Pinout

    Clear To Send RI or Power +5 VDC sourced by the Cradle Note: Pin 9 of this port is connected to +5 VDC and only approved Honeywell cables are to be used for communication between the cradle and external devices. 4-24...

  • Page 61: Power Connector Port

    Power Connector Port Note: When an external power supply is used to power these products, the external power supply should be UL Listed, with LPS or Class 2 outputs rated 12V, minimum 2 Amps. Cradle Power Connector Port Pinout Signal Wire Color Ground (CG) Green...
  • Page 62 4-26...

  • Page 63: Chapter 5: Technical Assistance

    Limited Warranty Honeywell International Inc. ("HII") warrants its products to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any HII product which is (i) improperly installed or used;...
  • Page 64 The duration of the limited warranty for the MX7 Tecton Battery Charger is 1 year. The duration of the limited warranty for the MX7 2200mAh Li-Ion and 1250mAh Li-Ion Battery is 6 months. The duration of the limited warranty for the MX7 AC power supply and cables is 1 year.
  • Page 66 Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com E-EQ-MX7OGWW Rev H 10/12...

Table of Contents