Table of Contents
Advertisement
Quick Links
BMW Parts and Accessories
Installation Instructions
Sound module system installation kit
BMW 5 Series touring (E 39/2) LHD
These installation instructions are only valid for:
•cars without an on-board monitor, without SA663 (BMW Profession radio) with a
production date after 09/00
•cars without an on-board monitor, with SA663 (BMW Profession radio) with a production
date after 02/01
•cars with an on-board monitor after production date 09/01
Technical and electrical knowledge required
The installation time is approx. 3.0 hours, which may vary depending on the condition of the car
and the equipment in it.
Retrofit / Installation kit No. 82 83 0 140 507
Retrofit / Installation kit No. 82 83 0 140 507
Installation Instructions No. 01 29 0 140 511
Issue date: 06.2001
F 39 0702 B
Advertisement
Table of Contents
Related Manuals for BMW 5 Series touring (E 39/2) LHD
Summary of Contents for BMW 5 Series touring (E 39/2) LHD
- Page 1 •cars without an on-board monitor, without SA663 (BMW Profession radio) with a production date after 09/00 •cars without an on-board monitor, with SA663 (BMW Profession radio) with a production date after 02/01 •cars with an on-board monitor after production date 09/01 Technical and electrical knowledge required The installation time is approx.
-
Page 2: Table Of Contents
Contents Section Page Important information for the installation of the sound module system in the E39/2. Preparations ............Parts list . -
Page 3: Important Information For The Installation Of The Sound Module System In The E39/2
This high quality audio system is to be used exclusively in conjunction with original BMW car radios. If it is fitted to other makes, BMW AG cannot accept any guarantee for the sound module system. The sound module system is only designed for installation in cars, which do not have an audio amplifier (for example cars with a hi-fi system or Harman Kardon hi-fi system). -
Page 4: Preparations
Preparations TIS instruction Cars without an on-board monitor radio only: Print out error memory Disconnect the battery 1200 Remove the cover in the footwell on the driver’s side Remove the A pillar trim on the driver’s side 51 43 201 Remove both door sill strips on the driver’s side 51 47 000 Remove the B pillar trim on the driver’s side... -
Page 5: Parts List
Parts list 039 0090 B Radio/Amplifier adapter cable Power supply cable with fuse Amplifier Fillister head self-tapping screw 4.5x9.5 (3x) Philips screw 3.5x7 (4x) Rattle guard Square seal for the rear speaker (2x) Tweeter (2x) Edge protector Sealing ring for 2-way rear speaker (2x) Front woofer (2x) 10 2-way rear speaker (2x) 11 Sealing ring for front woofer (2x) - Page 6 Parts list Kunden- Information 039 0091 B 19 Contact part 20 Insulation material for headlining (2x) 21 Base holder for amplifier 22 Cap nut 23 Hexagonal screw with washer, 4.8x16 24 Expanding nut 25 Cable holder 26 Template (cars with an on-board monitor radio only) EN/6 Retrofit / Installation kit No.
-
Page 7: Auxiliary Heating System Wiring Harness Connection Overview
Auxiliary heating system wiring harness connection overview 039 0092 B Cable colour/ Abbreviation / Item Description Connection location in the car Cross-section Slot Radio/Amplifier adapter cable New generation radio connection plug Cars without an on-board monitor radio: Radio in instrument panel Cars with an on-board monitor radio: Radio in spare wheel trough New generation adapter plug... -
Page 8: Installation And Cabling Diagram (For Cars Without An On-Board Monitor Radio Only)
Installation and cabling diagram (for cars without an on-board monitor radio only) 039 0093 B Lay the adapter cable A , as shown in the figure, and secure it with cable ties. When installing the adapter wiring harness A start with branches A1 and A2 . Branches A1 and A2 to the radio in the instrument panel Branch A3 to the earth post X1108 in the footwell on the left Branch A4 to the installation site of the amplifier on the A pillar on the left... -
Page 9: Installation And Cabling Diagram (For Cars Without An On-Board Monitor Radio Only)
Installation and cabling diagram (for cars without an on-board monitor radio only) 039 0094 B Lay the adapter cable A , as shown in the figure, and secure it with cable ties. When installing the adapter wiring harness A start with branches A1 and A2 . Branches A1 and A2 to the on-board monitor radio on the left-hand side of the boot Branch A3 to the earth post X13016 on the left-hand side of the boot Branch A4 to the installation site of the amplifier in the boot on the left... -
Page 10: To Install The Adapter Cable (Cars Without An On-Board Monitor Radio)
To install the adapter cable (cars without an on-board monitor radio) Lay the adapter wiring harness A, as shown in the figure, with branches A3 , A4 and A5 along the main wiring harness to the installation of the amplifier (30) and secure it with cable ties. 039 0095 B Pull up the carpet (30) in the driver’s footwell. - Page 11 To install the adapter cable (cars without an on-board monitor radio) If necessary, disconnect the white 12-pin connection plug X13321 and the black 12-pin connection plug X13598 from the new generation radio connection plug (30) on the audio wiring harness (31) and connect them to the new X13598 generation radio connection plug A1 on the adapter wiring harness A.
-
Page 12: To Install The Amplifier (Cars Without An On-Board Monitor Radio)
A pillar trim can be installed again without any problems. Check the Bowden cable for the bonnet. Holes in the body are to be treated with the anti-corrosion measures set out in BMW specifications. Ensure that the insulation strip is on the standard wiring harness. -
Page 13: To Install The Adapter Cable (Cars With An On-Board Monitor Radio)
To install the adapter cable (cars with an on-board monitor radio) If necessary, disconnect the white 12-pin connection plug X13321 and the black 12-pin connection plug X13598 from the new generation radio connection plug (30) on the audio wiring harness (31) and connect them to the new generation radio connection plug A1 on the adapter wiring harness A. - Page 14 To install the adapter cable (cars with an on-board monitor radio) Screw branch A3, brown cable with earth eyelet 6 mm to the earth post X13016. Lay branch A5 to terminal 30 post above the X13016 battery. 039 0110 B Lay branch A5, red cable strand on the radio/ amplifier adapter cable, along the standard wiring harness to terminal 30 post (30) above the battery...
-
Page 15: To Install The Amplifier (Cars With An On-Board Monitor Radio)
10. To install the amplifier (cars with an on-board monitor radio) Place the cut out drilling template (26) on to the base holder (21). Mark the holes on the base holder (21) using a centrepunch. Drill the four centrepunch points with a diameter of d = 4.5 mm. -
Page 16: To Install The Front Door Speakers
To install the front door speakers As you install the speakers it is essential that you ensure that the screws tap new threads since otherwise they will not hold the speakers securely. Ensure that the sealing ring is not in contact with the speaker diaphragm. - Page 17 11. To install the front door speakers Unclip the sealing cap from the cover (30).Secure the tweeter (6) in the speaker mounting on the cover (30) in the door trim (3) using the supplied Philips screws 3.5x7 (3). 039 0119 B EN/17 Retrofit / Installation kit No.
-
Page 18: To Install The Roof Speaker
12. To install the roof speaker The figure shows the installation of the speaker in the roof. Move the insulation (22) backwards and place it up to the edge of the tailgate (30) in the speaker openings between the metal and the headlining (the arrow (31) points to the front of the car). -
Page 19: To Adjust The Roof Speaker Cover
13. To adjust the roof speaker cover Remove the existing seal (30) from the speaker grille (31). Cut all the connecting struts between the edges and the outside edge with an angle cutter. Remove the inner edge (32) with the struts. 039 0123 B Place the adjusted speaker grille (30) through the foam ring and place it on the 2-way rear speaker. -
Page 20: Coding And Concluding Work
14. Coding and concluding work Coding - This system cannot be diagnosed and requires no encoding. Up to three remote control transmitters (26) can be programmed to operate with one receiver. Concluding work Connect battery Conduct a function test Reassemble the car by following the instructions for its dismantling in reverse order Print out error memory. -
Page 21: Function/Commissioning
After switching on the radio the volume control on the radio may only be adjusted very slightly. To prevent damaging the audio system the BMW sound module system is fitted with a delayed switch-on system. The amplifier does not come into full operation until 2 – 6 seconds after the radio is switched on.