Page 1
IBM Flat Panel Monitor Rack Mount Kit II Installation Instructions...
Page 3
IBM Flat Panel Monitor Rack Mount Kit II Installation Instructions...
Page 4
This publication was developed for products and services offered in the United States of America. IBM may not offer the products, services, or features discussed in this document in other countries, and the information is subject to change without notice. Consult your local IBM representative for information on the products, services, and features available in your area.
Note: The illustrations in this documentation might be slightly different from your hardware. The following general steps are required to install the Flat Panel Monitor Rack Mount Kit II. You can skip steps that do not apply or have already been performed.
3. Squeeze the sides of the hinge cover 2 and remove it. Note: Even though this hinge cover is not used with the Flat Panel Monitor Rack Mount Kit II, do not discard it. Store it with the other monitor stand parts you remove for possible future use.
6. Lay the monitor facedown on a cushioned surface and remove the six screws that secure the hinges to the flat panel monitor. Figure 3. Removing the existing monitor stand from the monitor 7. Lift off the hinge and monitor stand assembly. Store this assembly in a safe place for possible future use.
Note: The Flat Panel Monitor Rack Mount Kit II and keyboard tray require 3U of rack mounting space. If the keyboard tray does not have at least 2U of clearance above it, relocate the keyboard tray within the rack cabinet.
You must remove any keyboard or mouse that is already in the keyboard tray before continuing. b. You will not be able to store a mouse in the keyboard tray after installing the Flat Panel Monitor Rack Mount Kit II. c. You can only store a space-saver keyboard in the keyboard tray.
Note: Install or remove the flat panel monitor only when the display is in its upright position. 6. Secure the monitor stand in the back of the keyboard tray with the two provided screws 4 . Flat Panel Monitor Rack Mount Kit II Installation Instructions...
11. Snap the new hinge cover 2 into place over the hinge assembly. Note: Be sure to use the new hinge cover that comes with the Flat Panel Monitor Rack Mount Kit II because it has deeper grooves to accommodate the new hinge assembly.
You can now connect the power cord to the flat panel monitor and connect the display to a server. If you have an optional console switch, you can install it now as shown in “Installing an optional console switch” on page 9. Flat Panel Monitor Rack Mount Kit II Installation Instructions...
The console switch option is available separately, but additional mounting brackets come with the Flat Panel Monitor Rack Mount Kit II. You can use mounting brackets that come with the console switch to mount it vertically in the rack cabinet. Instructions for vertical mounting come with the console switch.
IBM or your reseller, if authorized by IBM, will make Engineering Changes (ECs) available that apply to your hardware. Be sure to retain your proof of purchase to obtain warranty service. Refer to the IBM hardware warranty for a full explanation of IBM's warranty terms.
Machine. If a Machine does not function as warranted during the warranty period, and IBM or your reseller are unable to either 1) make it do so or 2) replace it with one that is at least functionally equivalent, you may return it to your place of purchase and your money will be refunded.
Page 18
IBM or your reseller of changes in a Machine's location. IBM is responsible for loss of, or damage to, your Machine while it is 1) in IBM's possession or 2) in transit in those cases where IBM is responsible for the transportation charges.
Machine. If a Machine does not function as warranted during the warranty period, and IBM or your reseller are unable to either 1) make it do so or 2) replace it with one that is at least functionally equivalent, you may return it to your place of purchase and your money will be refunded.
Page 20
IBM or your reseller of changes in a Machine's location. IBM is responsible for loss of, or damage to, your Machine while it is 1) in IBM's possession or 2) in transit in those cases where IBM is responsible for the transportation charges.
Limitation of Liability: The following is added to this Section: Where IBM is in breach of a condition or warranty implied by the Trade Practices Act 1974, IBM's liability is limited to the repair or replacement of the goods or the supply of equivalent goods. Where that condition or warranty relates to right to sell, quiet possession or clear title, or the goods are of a kind ordinarily acquired for personal, domestic or household use or consumption, then none of the limitations in this paragraph apply.
Page 22
2. as to any other actual direct damages, IBM's liability will be limited to the total amount you paid for the Machine that is the subject of the claim. Applicability of suppliers and resellers (unchanged). FRANCE: Limitation of Liability: The following replaces the second sentence of the first paragraph of this Section: In such instances, regardless of the basis on which you are entitled to claim damages from IBM, IBM is liable for no more than: (items 1 and 2 unchanged).
(if recurring, the 12 months' charges apply) for the Machine that is the subject of the claim or which otherwise gives rise to the claim. The following item is added to this paragraph: 3. breach of IBM's obligations implied by Section 12 of the Sale of Goods Act 1979 or Section 2 of the Supply of Goods and Services Act 1982.
Page 24
Part Number: 32P0100 Printed in U.S.A. 32P 1...