Table of Contents
Advertisement
OPERATING
INSTR
UCTIONS
REGARD!NG TUNE INDICATOR
When tuning
to
an
FM
broadcast
with
the
LOCK/FM
MUTING
switch
set
to oN,
the
TUNE
indicator lights
to
show
the
reception
condition.
Conditions
of
the
TUNE
indicator are described as follows:
(>"<)
-
lndicates
no
reception
of
FM
broadcast.
(>.<)
-
lndicates
that
a broadcast
station
is
at
a
frequency
higher
than
that of the
digital
display. ln
this
case.
turn the TUNING
knob
clockwise
until
the middle
LED
of
the
TUNE indicator
lights.
(>.<)
-
lndicates
that
a
broadcast
station
is
tuned
in
correctly.
(>"<)
-
lndicates
that
a broadcast
station
is
at
a
frequency
lower than
that of the digital
display.
ln
this
case,
turn
the
TUNING knob counterclockwise
until
the
middle
LED
of
the
TUNE indicator
lights.
P.<, >.<)
-
lndicates
that the
incoming signal
is
strong
enough
to
overcome
the threshold of servo-lock
level.
Thus.
the
servo-lock
feature
is
activated
after
the
TUNING
knob
is
released and
automatically
takes over
further
precise
tuning
for
optimum
reception.
FM
RECEPTION
1.
Depress
the
FM
switch.
2.
Set
the
LOCK/FM MUTING
switch
to
ON.
3.
Turn
the tuning
knob
to
move
the dial
pointer
to
the
desired
frequency.
Fine
tune first so that as
many
SIGNAL
LEDs
as possible light,
then
tune carefully
so
that the
middle
LED
of
the TUNE indicator
lights.
The
LOCKED indicator
will
light
when
your
hand
is
removed
from the
tuning
knob.
This
shows
that the
selected
frequency
has
been locked
by
the servo-lock system
and
precise
tuning
will
be
maintained
automatically.
4.
Adjust
volume and tone
for
your
preference.
AM
RECEPTION
1.
Depress
the
AM
switch.
2.
Turn the
TUNING
knob to the desired
station.
Fine
tune
by observing
the SIGNAL indicator
and
tune
so
that
the
maximum number
of
LEDs light.
3.
Adjust volume and tone
for
your
preference.
TURNTABLES
1.
Depress
the
PHONO
1 or
PHONO
2
switch
of
the
SELECTOR
corresponding
to the turntable
connected
to
the
PHONO
1
or
PHONO
2
INPUT
iacks.
2.
Operate
the
turntable
selected
with the
SELECTOR
switch.
3. Adjust
the
volume and
the
MULTIPLE
ACOUSTIC
COMPENSATOR
controls
for you
preference.
TAPE
DECKS
Tape
Playback
1.
Set
the
MONITOR
switch
to A or
B
corresponding to
the
tape deck
connected
to the
TAPE
A
or
TAPE
B
jacks.
2.
Operate
the
tape deck connected
to
the
TAPE
jacks
and
playback
the
prerecorded
tape.
3. Adjust
the
volume and
the
MULTIPLE
ACOUSTIC
COMPENSATOR
controls
for your
preference.
Recording
(with
one tape
deck)
1.
Connect
the tape
deck
to the
TAPE
A
or TAPE
B jacks.
2. Set the
SELECTOR
switch
to
the
desired
program
sou
rce.
3.
Set
up your tape deck
for
recording.
4.
Set recording levels
with
the controls
on
your tape
deck.
5.
Adjust listening
level and tone for your preference
while
monitoring
the
signal being
recorded.
Recording
(with two tape
decks)
1.
Connect
two
tape
decks
to
the
TAPE
A
and
TAPE
B
jacks.
2. Set the
SELECTOR
switch
to
the
desired
program
source.
3.
Set
up your tape decks
for
recording.
4. Set
recording
levels
with the
controls
on
your
tape
decks.
5.
Adjust
listening level and tone for your preference
while
monitoring
the
signal being
recorded.
Monitoring
lf your tape deck
is
equipped
with
three
heads,
you
can
compare
the
sound quality
of the
recording
immediately
after
it
is
made
with
that of the
source
material.
Switching
the
MONITOR
switch
between SOU
or
A
(or
B)
permits
listening
comparisons
between recorded material
and
source material
while
the
recording
is
in
progress.
USE OF ADAPTOR
Depressing
the
ADAPTOR
switch on the front
panel
activates the equipement
(Dolby*
NR
unit,
Expander.
Tape
Deck.
etc.)
connected between
the
ADAPTO
R's
OUTPUT-INPUT
jacks on
the
rear
panel.
Reception
of
Dolby FM
broadcasts
1.
Connect
the
Dolby NR
unit
between
the
ADAPTOR'S
OUTPUT-INPUT
jacks.
2.
Shift
the
FM DE-EMPHASIS
switch
on
the
rear panel
to
the
25
&sec
Position.
3.
Depress
the
FM
switch.
4. Turn the
TUNING
knob
to
tune
in the
Dolby
FM
broadcast.
5.
Depress
the
ADAPTOR
switch.
6.
Operate
the
Dolby
NR unit
connected
between
the
ADAPTOR's
OUTPUT-INPUT
jacks.
7.
Adjust volume and tone
for
your
preference.
8.
The
Dolby
NR
unit
must
be
operated
following its
own
i
nstructions.
'r
Dolby
is
the Trademark
of
Dolby
Laboratories.
Tape Deck
Operation
When
a
tape deck
is
connected between
the
ADAPTOR's
OUTPUT-INPUT
jacks,
the
sound
recorded
on
the
tape
is similar
to the
sound heard
from
the
speaker.
lf
a
tape
deck equipped
with
three
heads (erase, recording,
and
playback),
the
recording on
the tape can
be monitored
by
depressing
the
ADAPTOR
switch.
FM DE.EMPHASIS SWITCH
Before shipment
this switch
has
been preset
to the
ap-
propriate position
for
the
expected delivery
area.
An incorrect
setting
will
adversely
affect
high frequen-
cy
response,
so
check
for
a
correct
setting
before
putting
the
unit into
operation.
U.S.A.
and
U.S.
military
..
75
p.s
European
countries,
Oceania
.............. 50
prs
il^ro.
The
25
ps
setting should be selected
when this
receiver
is
used
with an
auxiliary
Dolby* NR
adaptor
to
receive
Dolby
FM
broadcasts.
{'
Dolby is
the
Trademark
of
Dolby
Laboratories.
Hide quick links:
Advertisement
Table of Contents
