Re-Assigning Device Keys; Operating Other Components - Kenwood VR-716 Instruction Manual

Basic remote control operations for other components
5 To check the codes of your other components, repeat steps 1
through 4 , but substitute the appropriate key (i.e., AUX, VID2,
VID1, DVD/6CH, CD/DVD, M D/TAPE) for the component you
are checking.
• As suggested earlier on, w rite dow n each of the four-digit code.

Re-assigning device keys

The remote control can be set up to control a second TV or VCR, or any
combination of eight home entertainment components.
For example, to control the operation of tw o different VCR using the
remote control, the user need to re-assign the unused VID2 key to
operate the second VCR (VID1) as follow s:
1
Press and hold the Remote Setup key until the LED blinks
tw ice, then release the Remote Setup key.
2
Press the numeric key to enter "9 - 9 - 2".
• The LED w ill blink tw ice.
3 Press the VID1 key once, then press the VID2 key once.
• The user now can operate VID2 as a second VCR along w ith VID1.
• Refer to the table in the previous page for the combination of
source keys and the other components assignment.
4 To re-assign other device keys, repeat steps 1 through 3 by
substituting the key sequence from the chart below for the
most popular components:
To re-assign key
Sequence
TV as 2nd VID1 key Remote Setup -9 -9 -2 -VID1 - TV
TV as 2nd VID2 key Remote Setup -9 -9 -2 -VID2 - TV
TV as 2nd CD/DVD key Remote Setup -9 -9 -2 -CD/DVD - TV
TV back to TV key Remote Setup -9 -9 -2 -TV - TV
VID1 as 2nd TV key Remote Setup -9 -9 -2 -TV - VID1
VID1 as 2nd VID2 key Remote Setup -9 -9 -2 -VID2 - VID1
VID1 as 2nd CD/DVD key Remote Setup -9 -9 -2 -CD/DVD - VID1
VID1 back to VID1 key Remote Setup -9 -9 -2 -VID1 - VID1
5
To clear the re-assignment and reset the remote control to its
original operation mode:
1 Press and hold the Remote Setup key until the LED blinks tw ice,
then release the Remote Setup key.
2 Press the numeric key to enter "9 - 9 - 2".
3 Press the VID2 key tw ice.
• When a re-assignment is done, the LED w ill blink tw ice to confirm
your choice. At that time, you w ill need to program the remote
control in order to control the new component.
• If an invalid key sequence is entered, the LED blink once and return
to normal operation.
• When in Tuner mode, re-assignment is not available.
•
Perform

Operating other components

This operation lets you operate the registered components.
KENWOOD audio components w ith system control turn on and off
automatically w ith the receiver via the system control connections.
Source
keys
SRC Power
1
Use the Source keys to select the component you desire.
• Pressing the Source keys also changes the input selector on the
receiver.
• When you operate your registered DVD player, CD player, Cassette
deck, Cable, DTV decoders, VCR or TV, go to step 2.
• When you operate the CD player, Cassette deck, M D player, or
Tuner w ith system control connection, go to step 3.
2 Press the SRC (source) Pow er key.
• To return to the receiver operation mode, press the TUNER key for
more than 3 seconds.
3
Press the operation keys you desire.
The remote control mode remains at the selected input. If you
w ish to operate another component, repeat step 2 or 3.
Note
• Be sure to point the remote control at the remote sensor on the
receiver w hen you w ant to operate KENWOOD components connected
by system control cords. Otherw ise, point the remote control at the
component you w ant to operate.
• To initialize the remote control, press the Remote Setup key until the
LED blinks tw ice. Then press the numeric key to enter " 9-8-1" . The
LED blinks tw ice.
+ +
¢
4
+
7
›
29 EN