Related Manuals for ADT Pulse iCamera-1000
Summary of Contents for ADT Pulse iCamera-1000
- Page 1 ADT Pulse Interactive Solutions ® iCamera-1000-ADT Indoor Low-Light Camera Installation Guide...
-
Page 2: Table Of Contents
Rear Panel ......................4 INSTALLATION ......................5 Configuring and Installing the iCamera-1000-ADT ..........5 Adding the iCamera-1000-ADT to your ADT Pulse Wireless Network ... 6 Wall Mounting Instructions ..................11 PIR Video Motion Detection ................... 14 Enabling Motion Detection via the ADT Security System ....... 15 APPENDIX A: SPECIFICATIONS ................ -
Page 3: Introduction
Indoor Low-Light Camera Installation Guide Introduction This installation guide provides step-by-step instructions for configuring and installing your iCamera-1000-ADT Indoor Low-Light camera to your ADT Pulse ® wireless network. Permanent mounting instructions for the iCamera are also included. Overview The iCamera-1000-ADT (hereafter referred to as the iCamera) monitors your home or business in a low light or dark environment. -
Page 4: Package Contents
Indoor Low-Light Camera Installation Guide Package Contents 1. The iCamera-1000-ADT Indoor Low-Light Camera 2. Stand 3. Y-Cable 4. Power over Ethernet (PoE) Cable 5. 12V Power Adapter 6. Assembly Back Plate with three screws (packaged separately) 7. Wall Mount Plate 8. -
Page 5: Physical Details - Icamera-1000-Adt
Indoor Low-Light Camera Installation Guide Physical Details – iCamera-1000-ADT Front Panel Figure 1: Front Panel 1. Light Sensor Detects lighting conditions 2. IR LEDs The LEDs help you see clearly at night or in a dark environment. 3. Day Camera Lens The Day Camera Lens is used in a bright environment. -
Page 6: Rear Panel
Rear Panel Figure 2: Rear Panel 1. LAN Port Use in conjunction with the supplied LAN cable to connect your iCamera to the ADT Pulse Gateway. 2. Stand Mount The stand mount connects the stand to the iCamera. 3. Reset Button The reset button has two (2) functions: •... -
Page 7: Installation
Indoor Low-Light Camera Installation Guide Installation This section provides details of installing and configuring the iCamera-1000- ADT Indoor Low-Light camera. Configuring and Installing the iCamera-1000-ADT The following instructions provide details of configuring and installing the iCamera-1000-ADT Indoor Low-Light Camera to your ADT Pulse network. -
Page 8: Adding The Icamera-1000-Adt To Your Adt Pulse Wireless Network
Indoor Low-Light Camera Installation Guide Adding the iCamera-1000-ADT to your ADT Pulse Wireless Network 1. Open your web browser. In the address bar, type: https://Portal.ADTPulse.com. 2. Type your Username and Password, and then click the Sign In button. 3. Click the System tab, and then click the Manage Devices button. - Page 9 Indoor Low-Light Camera Installation Guide 4. In the Manage Devices Assistant, click Cameras. 5. Click the picture of the iCamera or select it from the drop-down list, and then click the Continue button. 6. Assign the iCamera a unique name (this is usually based on the location of the iCamera) in the space provided, and then type the iCamera’s MAC ID or...
- Page 10 Indoor Low-Light Camera Installation Guide 7. Click the Continue button. 8. Connect the camera to the Device Port of the gateway using the Ethernet cable (attached to the Y-Cable.) 9. Connect the supplied 12V power adapter to power up the iCamera, and then click the Continue button.
- Page 11 Indoor Low-Light Camera Installation Guide Please wait several minutes while the iCamera is being added to the network. NOTE: 10. Once connected, click the Continue button. 11. Click Finish after installation is complete. ADT Pulse Interactive Solutions ®...
- Page 12 Indoor Low-Light Camera Installation Guide Figure 4: Installation Using POE Cable 12. Unplug the Y-cable from the ADT Pulse Gateway, and then power off the camera. IMPORTANT IF CAMERA WILL BE INSTALLED AS A ‘WIRED’ CAMERA, USE THE LAN CABLE AND THE Y-CABLE. (REFER TO FIGURE 3 ON PAGE 5 OF THIS GUIDE.) IF CAMERA WILL...
-
Page 13: Wall Mounting Instructions
Indoor Low-Light Camera Installation Guide Wall Mounting Instructions Ensure that the iCamera is properly configured and added to the network before mounting the camera.* NOTE: 1. Stand Placement Locate an area where you want the iCamera to be mounted. Using the wall plate as a template, make two small marks inside the mounting holes of the wall plate. - Page 14 Indoor Low-Light Camera Installation Guide iCamera Wall Mounting Instructions (continued) 4. Hook the two mounting holes on the stand into the mounting screws. 5. Attach the iCamera Stand Locate the stand mount on the back of the iCamera. Fasten the stand by turning the iCamera counterclockwise until secured.
- Page 15 Indoor Low-Light Camera Installation Guide iCamera Wall Mounting Instructions (continued) 8. Connect the Power Adapter Connect the supplied power adapter to the PoE cable and power up. 9. Check the LEDs The Power LED turns on briefly, and then starts blinking for approximately 15 to 20 seconds.
-
Page 16: Pir Video Motion Detection
Indoor Low-Light Camera Installation Guide PIR Video Motion Detection The motion event will be captured when a significant image changes within the Window of Interest. The Window of Interest is defined below. The following installation hints should be noted: 1. -
Page 17: Enabling Motion Detection Via The Adt Security System
Indoor Low-Light Camera Installation Guide Enabling Motion Detection via the ADT Security System 1. Click the Automations tab, and then click the Add Automation button. 2. Select a trigger for this automation from the Trigger drop-down list. 3. Select Motion from the Event drop-down list. - Page 18 Indoor Low-Light Camera Installation Guide 8. Click OK. 9. Click Save. ADT Pulse Interactive Solutions ®...
-
Page 19: Appendix A: Specifications
Indoor Low-Light Camera Installation Guide Appendix A: Specifications Model iCamera-1000-ADT Dimensions, H x W x D 2.8” x 2.8” x 0.8” (72mm x 72mm x 20mm) (without stand) Operating Outdoors: -4°F to 113°F (-20°C to 45°C) Temperature Indoors: 32°F to 113°F (0°C to 45°C) Storage Temperature -4°F to 140°F (-20°... -
Page 20: Appendix B: Regulatory Approvals
Indoor Low-Light Camera Installation Guide Appendix B: Regulatory Approvals FCC Statement This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.