Table of Contents
Advertisement
0102 095 51642
Slimline Std Mk2 LPG
Slimline standard Mk 2
Multiflue
User, Installation & Servicing Instructions
This appliance is for use on PROPANE GAS (G31) ONLY at a supply pressure of 37mbar
Please hand this booklet to the user and advise to keep in a safe place
G.C. No
32-187-41B
Important Notice: Before disposal of the outer packaging, please enter the product code, purchase and
installation details in section 1.1 of this booklet.
MM79 010710
Advertisement
Table of Contents
Related Manuals for Royal Cozyfires Mk 2
Summary of Contents for Royal Cozyfires Mk 2
- Page 1 0102 095 51642 Slimline Std Mk2 LPG Slimline standard Mk 2 Multiflue User, Installation & Servicing Instructions This appliance is for use on PROPANE GAS (G31) ONLY at a supply pressure of 37mbar Please hand this booklet to the user and advise to keep in a safe place G.C.
-
Page 2: Table Of Contents
This booklet details instructions for USER (section 1), INSTALLATION (section 2) & SERVICING (section 3). IMPORTANT NOTICE It is important for the safe and continued operation of this appliance that the instructions contained in this booklet are observed! TABLE OF CONTENTS Section Instructions for Use Record of purchase/installation... -
Page 3: Instructions For Use
Page 1 Section 1 – Instructions for Use RECORD OF PURCHASE/INSTALLATION Slimline Standard Mk2 Purchase Details Date of purchase ______ / ______ / ______ Purchase from _____________________ Address _____________________ _________________________________________ Installation Details Date of installation ______ / ______ / ______ Installed by _____________________ Registration number... -
Page 4: Important Notes
Page 2 IMPORTANT NOTES Slimline Standard Mk2 CAUTION – THIS PACKAGE WEIGHS 16Kgs – assess the load before you move it and note any other handling information on the packaging. If you think the load is beyond your safe capability, DO NOT PUT YOURSELF AT RISK! Seek assistance from other person(s) and/or use appropriate handling equipment. -
Page 5: Re-Laying The Coal/Pebble Bed
Page 3 1. 4 RE - LAYING THE COAL/PEBBLE BED Slimline Standard Mk2 Fig. 3 The support shelf is positioned on the fibre support metalwork. There are two metal `stops’ that prevent the support shelf from sitting on the main burner outlet (Fig. -
Page 6: Spare Parts
Page 4 SPARE PARTS Slimline Standard Mk2 For a list of spare parts for this appliance, please refer to section 3.3. GUARANTEE Please complete the registration section of the white card supplied in the IFU kit. Any part of this appliance is guaranteed against the manufacturer’s defective workmanship or faulty materials for a period of twelve months from the date of purchase. -
Page 7: Important Notes
Page 5 Section 2 – Instructions for Installation IMPORTANT NOTES Slimline Standard Mk2 CAUTION – THIS PACKAGE WEIGHS 16Kgs – assess the load before you move it and note any other handling information on the packaging. If you think the load is beyond your safe capability, DO NOT PUT YOURSELF AT RISK! Seek assistance from other person(s) and/or use appropriate handling equipment. -
Page 8: Technical Data
Page 6 TECHNICAL DATA Slimline Standard Mk2 Fig. 7 Minimum height of opening is 555mm 600mm Forward projection is 50mm w/out front/fret 85mm with front/fret Minimum Fig. 8 width of opening is 410mm 505mm Depth is 130mm w/out cable fixing 160mm with cable fixing SPECIFICATIONS Injector... - Page 9 Page 7 2.4.1 INSTALLING THE APPLIANCE (Flue) Any permanent flue restriction must be removed and any variable dampers locked fully open or removed. If the flue has been used previously for solid fuel, it must be swept PRIOR to installation. This appliance is suitable for installation into CLASS 1, Class 2 and PRE-CAST flues.
-
Page 10: Clearance To Sides And Shelves
Page 8 2.4.2 INSTALLING THE APPLIANCE (Clearance to sides and shelves) Slimline Standard Mk2 The minimum clearance to any combustible material to the side of the appliance must be 150mm (Fig. 12). The minimal clearance to the underside of a 150mm depth combustible shelf from the hearth must be 790mm. Add 12.5mm to this clearance for every 25mm increased depth of shelf (Fig. -
Page 11: Restrictor Plate
Page 9 2.4.4 INSTALLING THE APPLIANCE (Fitting the appliance in position) Slimline Standard Mk2 BEFORE COMMENCING WORK, TURN OFF ALL APPLIANCES THAT ARE FED BY THE METER. ISOLATE THE GAS SUPPLY BY TURNING OFF AT THE METER. It will be necessary to dismantle the burner unit from the firebox before installation into the opening. Remove the two fixing screws on the left and right hand side of the burner. -
Page 12: Fitting The Firebox In The Opening
Page 10 2.4.4.2 INSTALLING THE APPLIANCE (Fitting the firebox in the opening) Slimline Standard MK 2 There are two options to fit the firebox into the opening:- Prior to fitting the firebox, fit the foam seal provided. It should be positioned approximately 10mm from the outside edge of the metalwork. -
Page 13: Connecting The Gas Supply
Page 11 2.4.4.3 INSTALLING THE APPLIANCE (Connecting the gas supply) Slimline Standard Mk2 A restrictor elbow complete with pressure test point is fitted to the appliance to facilitate servicing. The gas supply to the appliance may be from the left or right hand side or even a concealed fitting from the rear. Two holes are provided at the rear of the firebox to help facilitate a concealed connection. -
Page 14: Laying The Coal/Pebble Bed
Page12 LAYING THE COAL/PEBBLE BED Slimline Standard Mk2 Fig. 22 The support shelf is positioned on the fibre support metalwork. There are two metal `stops’ that prevent the support shelf from sitting on the main burner outlet (Fig. 22). Metal `stops’ Fig. -
Page 15: Clearance Of Combustion Products
Page 13 CLEARANCE OF COMBUSTION PRODUCTS Slimline Standard Mk2 Relight the appliance and allow to run for five minutes with the gas control in the `HIGH’ position. Check for 20mm down Fig. 26 satisfactory clearance of combustion products by inserting from this point a lighted smoke match into the opening 20mm down from 80mm from... -
Page 16: Removal Of Debris Or Soot
Page 14 Section 3 – Maintenance & Servicing REMOVAL OF DEBRIS OR SOOT Slimline Standard Mk2 Allow the appliance to cool for two to three hours before removing all of the fibre components for cleaning purposes. Once all the fibre is removed, check that no debris is located in the burner holes of the appliance. -
Page 17: Spare Parts
Page 15 SLIMLINE STANDARD Mk2 (32-187-41B) SPARE PARTS BRITISH GAS PART DESCRIPTION CROSSLEE PART No QUANTITY COUNCIL NUMBER Aeromatix Burner (Propane) (Manuf. No.AC03/211657) 0102 078 02471 E86-786 Piezo Ignitor c/w Steel Nut (Manuf. No. 66142/100) 40245 397-686 120M Straight Injector (Manuf. No. 044-341-196-120M) 0102 078 02461 E86-788 Ignition Lead (250mm) -
Page 18: Useful Telephone Numbers
Page 16 USEFUL TELEPHONE NUMBERS In the event that you may require service, spares or technical information, please contact us at: - Crosslee PLC Halifax West Yorkshire HX3 8DE Telephone Customer Service 01422 203963 01422 204767 Service Engineer (REPAIRCARE) 0844 8797422* *Calls cost 5p per minute from a UK BT landline. - Page 19 Page 17 MM79 010710...