Related Manuals for Whirlpool ADN 640
Summary of Contents for Whirlpool ADN 640
- Page 1 0806_GB_42 Instructions for installation, use e maintenance GAS PASTA COOKER ADN 640 04/2008...
- Page 2 CHARACTERISTICS Supplied by: Date: Customer Service: e-mail 0806_GB_42 - GAS PASTA COOKER 04/2008 2 · 12...
-
Page 3: Table Of Contents
INDEX Diagram Characteristics of the appliances Technical data 4 Installation instructions 4.1 Safety rules 4.2 Structure, framework and safety devices of the appliances 4.3 Assembly 4.3.1 Installation premises 4.3.2 Statutory regulations and technical requirements 4.3.3 Installation 4.3.4 Gas connection 4.3.5 Water connection 4.3.6 Smoke extraction Operation preparation 5.1 Preparation and Start-up... -
Page 4: Diagram
1 - DIAGRAM ADN 640 Water drainpipe Water drainpipe 1"GC female 1"GC female Gas 1/2" Water load pipe Ø12 Data plate Water load pipe Ø12 Gas 1/2" Data plate 0806_GB_42 - GAS PASTA COOKER 04/2008 4 · 12... -
Page 5: Characteristics Of The Appliances
THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL. 20 mbar 3 - TECHNICAL DATA Model Description Dimensions in mm. (LxDxH) N˚ Tank Capacity ADN 640 Gas pasta cooker 400 x 700 x 900 26 l 51BS3549 TABLE 1 ADN 640 Model... -
Page 6: Installation Instructions
4 - INSTALLATION INSTRUCTIONS 4.1 Safety rules 4.3 Assembly 4.3.1 Installation premises • Only a local gas utility technician is authorized to carry out gas installations and connections. The statutory regulations (applied The appliance must be installed in a well-ventilated room, and if in Germany VDE, Austria ÖVE, Switzerland SEV, etc.) and connec- possible under a range hood (check current regulations). -
Page 7: Preparation And Start-Up
5 - SET-UP FOR OPERATION 5.1 Preparation and Start-up using a gas meter according to the so-called "volumetric method". A simple inspection is usually enough to check if injectors are func- tioning correctly. Before starting up the appliance, remove the protective wrapping. Then carefully clean the working surface and the external parts with lukewarm water and detergent, using a damp rag to remove all traces 5.1.3 Checking the input pressure... -
Page 8: Power Check For Operation With Liquid Gas
5 - SET-UP FOR OPERATION Fig. 2 32 30 5.1.8 Checking the primary air 5.1.5 Power check for operation with liquid gas Check if the type of injectors used meet the data of the table 1. The burner is equipped with primary air adjustment. Distance “A” (fig. -
Page 9: Setting Reduced Capacity Power
5 - SET-UP FOR OPERATION After the replacement check the seal using a leack detector spray. After any maintenance or repair work, replace the con- trol panel and the lower panel. After replacing gas input components, check operation 5.1.13 Setting reduced capacity power again and test for leakage. -
Page 10: Instructions For Use
6 - INSTRUCTIONS FOR USE 6.1 Safety, cleaning and repair rules 6.2.2 Lighting the main burner and temperature adju- stment • This appliance is used for the preparation of meals at industri- To light the main burner, after light the pilot burner, place the knob al level. -
Page 11: Weee Directive
6 - INSTRUCTIONS FOR USE 6.6 Recommendations for the treatment of formed rust spots can be removed with slightly abrasive liquid soaps or fine-grained sand paper. Larger rust spots can be stainless “steel industrial” kitchens removed with 2-3% of hot oxalic acid solution. If these cleaning products do not do the job, a nitric acid (10%) treatment is 6.6.1 Useful information on “stainless steel”... - Page 12 THE MANUFACTURER RESERVES THE RIGHT TO MAKE ANY CHANGES DEEMED NECESSARY. THE MANUFACTURER CANNOT BE HELD RESPONSIBLE IF THE INSTRUCTIONS CONTAINED IN THIS MANUAL ARE NOT OBSERVED. WHIRLPOOL EUROPE srl V.le Guido Borghi, 27 I – 21025 Comerio – VA...