Related Manuals for Whirlpool ADN 632
Summary of Contents for Whirlpool ADN 632
- Page 1 0804_GB_42 Instructions for installation, use e maintenance GAS FRY TOP ADN 632 ADN 633 · ADN 634 ADN 635 · 04/2008...
- Page 2 CHARACTERISTICS Supplied by: Date: Customer Service: e-mail 0804_GB_42 - GAS FRY TOP 04/2008 2 · 12...
- Page 3 INDEX Diagram Characteristics of the appliances Technical data 4 Installation instructions 4.1 Safety rules 4.2 Structure, framework and safety devices of the appliances 4.3 Assembly 4.3.1 Installation premises 4.3.2 Statutory regulations and technical requirements 4.3.3 Installation 4.3.4 Gas connection 4.3.5 Smoke extraction Operation preparation 5.1 Preparation and Start-up 5.1.1 Start-up...
- Page 4 1 - DIAGRAM ADN 634 ADN 632 ADN 635 ADN 633 Gas 1/2" Gas 1/2" Data plate Gas 1/2" Gas 1/2" Data plate Data plate 0804_GB_42 - GAS FRY TOP 04/2008 4 · 12...
-
Page 5: Characteristics Of The Appliances
20 mbar 3 - TECHNICAL DATA Model Description Dimensions in mm. (LxDxH) Area plate 0,165 dm ADN 632 Smooth plate gas Fry Top 400 x 700 x 900 51BS3544 ADN 633 Grooved plate gas Fry Top 400 x 700 x 900... -
Page 6: Installation Instructions
4 - INSTALLATION INSTRUCTIONS 4.1 Safety rules 4.3 Assembly • Only a local gas utility technician is authorized to carry out gas 4.3.1 Installation premises installations and connections. The statutory regulations (applied The appliance must be installed in a well-ventilated room, and if in Germany VDE, Austria ÖVE, Switzerland SEV, etc.) and connec- possible under a range hood (check current regulations). -
Page 7: Set-Up For Operation
5 - SET-UP FOR OPERATION 5.1 Preparation and Start-up If you wish to further check the nominal power, you may do so by using a gas meter according to the so-called "volumetric method". A simple inspection is usually enough to check if injectors are func- Before starting up the appliance, remove the protective wrapping. -
Page 8: Operation Control
5 - SET-UP FOR OPERATION 5.1.5 Power check for operation with liquid gas 5.1.9 Conversion and adjustment Check if the type of injectors used meet the data of the table 1. To change over form one kind of gas to another, for example from methane to liquid gas, or to another type of gas, the use of suitable Check that the pressure reducer installed in the system has an outlet injectors for the main burner is required, in accordance with the... -
Page 9: Setting Reduced Capacity Power
5 - SET-UP FOR OPERATION After the replacement check the seal using a leack detector spray. 5.3.5 Burner fry top 600 Unscrew the screws (pos. 2 and 5 fig. 2B) fixing the burner to the injector-holder collector nuts (pos. 4 fig. 2B) and on the combustion 5.1.12 Setting reduced capacity power chamber, lift up the burner (pos. -
Page 10: Safety, Cleaning And Repair Rules
6 - INSTRUCTIONS FOR USE 6.1 Safety, cleaning and repair rules Special precautions It is recommanded to keep cleaning the plate during use, • This appliance is used for the preparation of meals at industri- using a scraper or a dampf cloth to remove particles of food al level. - Page 11 6 - INSTRUCTIONS FOR USE 6.6 Recommendations for the treatment of soaps or fine-grained sand paper. Larger rust spots can be removed with 2-3% of hot oxalic acid solution. If these cleaning stainless “steel industrial” kitchens products do not do the job, a nitric acid (10%) treatment is required.
- Page 12 THE MANUFACTURER RESERVES THE RIGHT TO MAKE ANY CHANGES DEEMED NECESSARY. THE MANUFACTURER CANNOT BE HELD RESPONSIBLE IF THE INSTRUCTIONS CONTAINED IN THIS MANUAL ARE NOT OBSERVED. WHIRLPOOL EUROPE srl V.le Guido Borghi, 27 I – 21025 Comerio – VA...
Need help?
Do you have a question about the ADN 632 and is the answer not in the manual?
Questions and answers