Download Print this page

Black & Decker 7" RANDOM ORBITALWAXER Instruction Manual

7" random orbital waxer

Advertisement

Quick Links

7" RANDOM
ORBITAL WAXER
INSTRUCTION MANUAL
SAVE THIS MANUAL FOR FUTURE REFERENCE.
GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL TOOLS
READ ALL INSTRUCTIONS
WARNING: Read all instructions before operating product. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious injury.
AVOID DANGEROUS ENVIRONMENTS:
tools in the rain.
All visitors should be kept at a distance from work area.
KEEP CHILDREN AWAY.
When not in use, tools should be stored indoors in dry, and
STORE IDLE TOOLS INDOORS.
high or locked-up place – out of reach of children.
It will do the job better and with less likelihood of a risk of injury at
DON'T FORCE TOOL.
the rate for which it was designed.
Do not use the tool for any job except that for which it is intended.
USE RIGHT TOOL.
Do not wear loose clothing or jewelry. They can be caught in moving
DRESS PROPERLY.
parts. Rubber gloves and substantial, non-skid footwear are recommended when working
outdoors. Wear protective hair covering to contain long hair.
USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT.
with side shields, complying with applicable safety standards and, when needed, a face
shield. Also use face or dust mask if operation is dusty. This applies to all persons in the
work area. Also use a hard hat, hearing protection, gloves, safety shoes and dust collection
systems when specified or required. Safety glasses or the like are available at extra cost at
your local dealer or Black & Decker Service Center.
Never carry tool by cord or yank it to disconnect from receptacle. Keep cord
DON'T ABUSE CORD.
from heat, oil, and sharp edges.
Use clamps or a vise to hold work. It's safer than using your hand and it frees both
• SECURE WORK.
hands to operate tool.
Keep proper footing and balance at all times.
DON'T OVERREACH.
Disconnect the tool from the power supply when not in use, before
DISCONNECT TOOLS.
servicing, and when changing accessories such as bonnets and the like.
Don't carry plugged-in tool with finger on switch. Be sure
AVOID UNINTENTIONAL STARTING.
switch is off when plugging in.
GROUND FAULT CIRCUIT INTERRUPTER (GFCI)
or outlets to be used. Receptacles are available having built in GFCI protection and may
be used for this measure of safety.
USE OF ACCESSORIES AND ATTACHMENTS.
recommended for use with this tool could be hazardous. Refer to the accessory section
of this manual for further details.
Watch what you are doing. Use common sense. Do not operate tool when you
STAY ALERT.
are tired.
Before further use of the tool, a guard or other part that is
CHECK DAMAGED PARTS.
damaged should be carefully checked to determine that it will operate properly and perform
its intended function. Check for alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions that may affect its operation. A
guard or other part that is damaged should be properly repaired or replaced by an
authorized service center unless otherwise indicated elsewhere in this instruction manual.
Have defective switches replaced by authorized service center. Do not use tool if switch
does not turn it ON and OFF.
portable electric tools near flammable liquids or in gaseous or explosive
DO NOT OPERATE
atmospheres. Motors in these tools normally spark, and the sparks might ignite fumes.
When tool is used outdoors, use only extension cords
OUTDOOR USE EXTENSION CORDS.
intended for use outdoors and so marked.
Make sure your extension cord is in good condition. When using an
EXTENSION CORDS.
extension cord, be sure to use one heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line voltage resulting in loss of power and
overheating. The accompanying table shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller
the gage number, the heavier the cord.
Catalog Number W007B
Don't use tools in damp or wet locations. Don't use
Use safety goggles or safety glasses
protection should be provided on the circuits
The use of any accessory or attachment not
Minimum Gage for Cord Sets
V
l o
s t
120V
0-25
(0-7,6m)
240V
0-50
(0-15,2m) (15,2-30,4m)
Ampere Rating
More
Not more
Than
Than
0 -
6
18
6 -
10
18
10 -
12
16
12 -
16
14
SAFETY GUIDELINES / DEFINITIONS
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided,
may result in property damage.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should always be
followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or
equipment could result in serious injury and property damage. There are certain applications for which tools
and equipment are designed. Black & Decker strongly recommends that this product NOT be modified and/or
used for any application other than for which it was designed. Read and understand all warnings and
operating instructions before using any tool or equipment.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: This product or its power cord contains lead, a chemical known to the State of
California to cause cancer and birth defect or other reproductive harm. Wash hands after handling.
WARNING: RISK OF ELECTRICAL SHOCK:
• Hold tool by insulated gripping surface when performing an operation where the tool may
contact hidden wiring or its own cord. Contact with "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
• Avoid body contact with grounded surfaces such as pipes, radiators, range, and
refrigerators. There is a risk of electrical shock if the body is grounded.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• THIS UNIT IS NOT FOR USE BY CHILDREN AND SHOULD ONLY BE OPERATED BY
ADULTS.
• Do not immerse unit in water.
• Do not drop or throw unit.
• Pull cord by plug rather than cord when disconnecting the unit from power source.
• Power Switch should be in the OFF position when the unit is not in use. Make sure switch
is in the OFF position before connection to a power source.
• Do not crush, cut, pull or expose cord to extreme heat.
• Position cords so they do not become entangled or become a safety hazard. Keep cords
away from sharp edges.
• Use in a dry location only.
• Do not open body casing. There are no user-serviceable parts inside. Opening the body
casing will void manufacturer's warranty.
• Do not use any accessory that is not recommended or provided by the manufacturer.
• To avoid possible damage that may shorten the unit's working life, protect it from direct
sunlight, direct heat and/or moisture.
• Do not allow power cord to contact the rotating bonnet.
• Allowing dust to get into mouth, eyes, or lay on skin may promote absorption of harmful
chemicals.
ADDITIONAL SPECIFIC SAFETY INSTRUCTIONS
WARNING: RISK OF PERSONAL INJURY:
• DO NOT use string tie (or drawstring) polishing pads or bonnets with this unit. Extreme
personal injury may result if fingers are caught by rotating string tie. USE ONLY bonnets
with elastic bands.
• Failure to properly seat the Bonnet to the pad may result in the Bonnet being thrown from
the pad.
• Always maintain a firm grip on the Waxer/Polisher handle(s) to prevent loss of control.
WARNING: RISK OF PERSONAL INJURY OR PROPERTY DAMAGE:
• Use of this tool can generate and/or disburse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE WHEN USING THIS
WAXER/POLISHER:
• Use clamps or another practical way to secure and support the work piece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss
of control.
• Do not use tool if Power Switch does not turn it ON or OFF. Any tool that cannot be
controlled with the power switch is dangerous and must be repaired.
• Operate this waxer/polisher ONLY on AC current on which the voltage is within correct
limits (120 volts). Never attempt to operate on DC current. To do so may seriously
damage the waxer/polisher.
• Always disconnect the unit's cord plug from power source before making any
adjustments, changing bonnets or storing the tool to reduce the risk of accidentally
starting the waxer/polisher.
• Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the waxer/polisher's operation. If damaged, have the tool
serviced before using.
• Use only accessories that are supplied or recommended by the manufacturer for this
model. Refer to the "Accessories" section of this Instruction Manual for more
information.
• NEVER allow Gasoline, Brake Fluids or any petroleum-based products to come in contact
with plastic parts or power cord. They contain chemicals that can damage, weaken or
destroy plastic and insulation.
• Read And Understand This Instruction Manual Before Using This Unit.
SAVE THESE INSTRUCTIONS
INTRODUCTION
Thank you for choosing the Black and Decker
use waxer/polisher imitates a hand polishing motion leaving an even finish with no hot spots, streaks or
swirls. The random orbital movement of the polisher oscillates as it rotates, so it is ideal for delivering a
shine that ordinarily takes hours to produce by hand. Please read this guide carefully before use to
ensure optimum performance and avoid damage to the unit or items that you are using it with.
FEATURES
• Powerful, high performance, quiet running motor
• Three polishing bonnets included (Wax Applicator, Wax Off and Polishing)
• Ideal for buffing cars, boats, trucks, SUVs and recreational vehicles
• Safe for all finishes, lightweight and easy to use
T
t o
l a
L
e
n
g
h t
f o
C
o
d r
n i
F
e
t e
26-50
51-100
101-150
(7,6-15,2m)
(15,2-30,4m)
(30,4-45,7m)
51-100
101-200
201-300
(30,4-60,9m)
(60,9-91,4m)
American Wire Gage
16
16
14
16
14
12
16
14
12
12
Not Recommended
7" Random Orbital Waxer . This lightweight and easy to
®

Advertisement

loading

Summary of Contents for Black & Decker 7" RANDOM ORBITALWAXER

  • Page 1: Important Safety Instructions

    Minimum Gage for Cord Sets 120V 0-25 26-50 51-100 101-150 (0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m) 240V 0-50 51-100 101-200 201-300 (0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m) 7" RANDOM Ampere Rating More Not more American Wire Gage ORBITAL WAXER Than Than INSTRUCTION MANUAL 10 - 12 - Not Recommended SAFETY GUIDELINES / DEFINITIONS...
  • Page 2: Care And Maintenance

    Controls and Features Plastic parts may be wiped clean with a soft damp cloth. NEVER use solvents when cleaning any plastic part as this may damage the finish. DO NOT IMMERSE THE WAXER OR ATTACHED FOAM PAD IN WATER. Storage Store the waxer in a “pad-up”...

This manual is also suitable for:

W007b