Table of Contents
Advertisement
Quick Links
OPERATING AND MAINTENANCE INSTRUCTIONS MANUAL
PFT510
BATTERY-POWERED VIC-PRESS
WARNING
If you need additional copies of any literature, or if you have questions concerning the safe
and proper operation of this tool, contact Victaulic, P.O. Box 31, Easton, PA 18044-0031,
Phone: 1-800-PICK VIC, E-Mail: pickvic@victaulic.com
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.
REV_D
TOOL FOR VIC-PRESS SCHEDULE 10S SYSTEM PRODUCTS
™
Vic-Press
WARNING
Failure to follow instructions and warnings could result in serious
personal injury, property damage, and/or product damage.
• Before operating or servicing the PFT510 Vic-Press Schedule 10S Tool
read all instructions in this manual and all warning labels on the tool.
• Before attempting to install any Vic-Press products, read the I-P500
Field Installation Handbook.
• Wear safety glasses, hardhat, foot protection, and hearing protection.
• Save this operating and maintenance manual.
HE.13987
SCHEDULE 10S
SYSTEM PRODUCTS
TM-PFT510
™
TM-PFT510
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Victaulic TM-PFT510
Summary of Contents for Victaulic TM-PFT510
- Page 1 • Save this operating and maintenance manual. If you need additional copies of any literature, or if you have questions concerning the safe and proper operation of this tool, contact Victaulic, P.O. Box 31, Easton, PA 18044-0031, Phone: 1-800-PICK VIC, E-Mail: pickvic@victaulic.com www.victaulic.com...
-
Page 2: Table Of Contents
EC Declaration of Conformity . . . . . . . . . . . . .23 www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D... -
Page 3: Operator Safety Instructions
Non-skid footwear and rubber gloves are operation, and hazardous situations . recommended when working outdoors . 17. Do not remove any labels from the tool. Replace any damaged or worn labels . www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_2... -
Page 4: Introduction
21. Keep the battery away from metal objects The Victaulic PFT510 Vic-Press Schedule 10S that can make a connection from one Tool is designed for joining only Victaulic Vic- terminal to another. Shorting the battery Press Schedule 10S System products with terminals may cause burns or a fire . -
Page 5: Receiving The Tool
1 Each Vic-Press Ring for 11/2-inch/48.3-mm and 2-inch/60.3-mm Vic-Press Schedule 10S System Products Vic-Press Adapter Jaw Victaulic Vic-Press Schedule 10S System Products Field Installation Handbook (I-P500) Pipe Marking Gauge Instructions (I-P500.Gauge) Pipe Marking Gauges for 11/2-inch/48.3-mm and 2-inch/60.3-mm Pipe Paint Stick Wire Brush www.victaulic.com... -
Page 6: Using The Dolly To Transport The Tool Or
Engage this lower bracket with the lower bar on the back of the tool or accessory case . Release the button and make sure the dolly is secured to the case . www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_5... -
Page 7: Battery And Battery Charger Information
. 1 . Plug the battery charger into a proper AC power source . 1a . Insert the battery into the battery charger, as shown above . www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_6... -
Page 8: Temperature Requirements For Operating
Charged Battery temperatures less than 14° F/-10° C or greater 0.840 than 122° F/50° C . 21.3 1.050 26.9 1.315 33.7 1.900 1 1/2 48.3 2.375 60.3 www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_7... -
Page 9: Tool Nomenclature
Vic-Press jaw or Vic-Press ring before attempting to perform the pressing operation. Failure to follow these instructions could cause system failure, resulting in serious personal injury and property damage. www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_8... -
Page 10: Tool Setup
4 . Select the proper size standard Vic-Press jaw or Vic-Press adapter jaw for the pipe/fitting size being installed . NOTE: The size is stamped on the standard Vic-Press jaw/Vic-Press ring . www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_9... - Page 11 Vic-Press jaw or Vic-Press adapter jaw engaged in the lower/back position) must be aligns properly to permit insertion of the locking used for 1 1/2-inch/48 .3-mm and 2-inch/60 .3- pin . mm sizes . www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_10...
- Page 12 The tool will not operate correctly if the locking pin is not fully engaged, resulting in tool damage. www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_11...
-
Page 13: Pressing Operation For 1/2-Inch/21 .3-Mm
Press jaw to close around the fitting . 1 . Check the standard Vic-Press jaw for damage or wear before performing the pressing operation . Replace any damaged or worn standard Vic-Press jaws . www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_12... - Page 14 Vic-Press jaw by squeezing pinch points during the the levers . Remove the tool from the fitting/pipe . pressing operation. Failure to follow this instruction could result in serious personal injury. www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_13...
-
Page 15: Pressing Operation For 1 1/2-Inch/48 .3-Mm
Vic-Press ring arm . Allow or worn components should be returned to a the Vic-Press ring to open completely, as shown Victaulic-authorized service facility . above . www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_14... - Page 16 . To ease handling, the Vic-Press ring can be installed onto the fitting prior to inserting the pipe ends into the fitting, as shown above . www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_15...
- Page 17 7 . Engage the Vic-Press adapter jaw hooks into the Vic-Press ring, and release the levers . Make sure all four hooks of the Vic-Press adapter jaw engage completely with the Vic-Press ring . www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_16...
- Page 18 8d . Remove the Vic-Press ring from the fitting by pulling the latching pin out until it disengages the Vic-Press ring arm, as shown in Step 3 of this section . www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_17...
-
Page 19: Standard Vic-Press Jaw Or
. Remove the standard Vic-Press jaw or Vic-Press adapter jaw 1 . Remove the battery from the tool by from the tool . depressing the button, as shown above . www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_18... - Page 20 3b . Lubricate the locking pin with a light machine oil . 4 . Clean plastic components (i .e . batteries, tool housing, etc) with a mild soap and damp cloth . www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_19...
-
Page 21: Battery And Battery Charger
9 . Coat the entire standard Vic-Press jaw, Vic- Press adapter jaw, and Vic-Press rings with an industrial grade lubricant/anti-corrosion spray . 10 . Charge the batteries by following the “Battery and Battery Charger Information” section . www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_20... -
Page 22: Troubleshooting
Vic-Press jaw and into the tool until it clicks. During the pressing operation, a ridge is Damaged or worn Vic-Press jaw/Vic-Press Replace the Vic-Press jaw with a new, Victaulic- created on the fitting. jaw contour. supplied Vic-Press jaw for Vic-Press Schedule 10S System Products (supplied by Victaulic). -
Page 23: Indicator Lights/Sounds
The required pressure has not been reached due to mechanical error while After working cycle the motor was running/ 3 Times 3 Times Return tool to Victaulic for servicing www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_22... -
Page 24: Ec Declaration Of Conformity
TM-PFT510 OPERATING AND MAINTENANCE INSTRUCTIONS MANUAL www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. REV_D TM-PFT510_23... - Page 25 TOOL FOR VIC-PRESS SCHEDULE 10S SYSTEM PRODUCTS ™ For complete contact information, visit www.victaulic.com TM-PFT510 6230 REV D UPDATED 10/2012 RM00PFT510 VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
Need help?
Do you have a question about the TM-PFT510 and is the answer not in the manual?
Questions and answers