Download
Share
Print this page
Nikon VBA15001 Black Repair Manual
  1. Manuals
  2. Brands
  3. Nikon Manuals
  4. Digital Camera
  5. VBA15001 Black
  6. Repair manual
Nikon VBA15001 Black Repair Manual

Nikon VBA15001 Black Repair Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Printed in Japan Nov 2006
VBA15001
VBA15101
REPAIR MANUAL
作成承認印
Black
Silver
Q033
060710_
Copyright© 2006 by NIKON CORPORATION.
All Rights Reserved.
無断転載を禁ず！！
INC
VBA15001-R.3701.A
配布許可印
サービス
計画課
Ｍ

Advertisement

loading

Related Manuals for Nikon VBA15001 Black

Summary of Contents for Nikon VBA15001 Black

  • Page 1 VBA15001-R.3701.A 作成承認印 配布許可印 サービス 計画課 Ｍ VBA15001 Black VBA15101 Silver Q033 060710_ REPAIR MANUAL Copyright© 2006 by NIKON CORPORATION. All Rights Reserved. 無断転載を禁ず！！ Printed in Japan Nov 2006...
  • Page 2 Format (DPOF) Compression • NEF (RAW): compressed 12-bit • JPEG: JPEG baseline-complaint Autofocus TTL phase detection by Nikon Multi-CAM 530 autofocus sensor module with AF-assist illuminator (range approximately 0.5–3.0m/1ft. 8in.–9ft. 10in.) Detection range –1.0–+19EV (ISO 100 at 20°C/68°F) AF-area mode...
  • Page 3 3s after ash is red at full output Accessory shoe Standard ISO hot-shoe contact with sync, signal, and ground contacts and safety lock Nikon Creative Lighting Supported with built-in ash, SB-400, SB-800, and SB-600; Advanced Wireless Lighting System supported with SB-800 or SU-800 as Commander.
  • Page 4 Chinese (Simpli ed and Traditional), Dutch, English, Finnish, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian, Spanish, Swedish Power source • One rechargeable Nikon EN-EL9 Li-ion battery; charging voltage (MH-23 quick charger): 7.4V DC • EH-5 AC adapter (available separately; requires optional EP-5 AC adapter connector) Dimensions (W×D×H)
  • Page 5 VBA15001-R.3701.A Points to notice for Disassembly / Assembly WARNING 警告 Due to an internal high voltage area, take extra care not to get 内部に高電圧部あり。カバーを外す時は感電に注意すること。 an electric shock when detaching covers. カバーを外した後は、修理指針の指示に従ってメインコンデン After removing covers, b e sure to discharge the main condenser according to the instructions of repair manuals .
  • Page 6 VBA15001-R.3701.A Disassembly 1. Separation of Front and Rear Bodies Bottom Cover #5674×2 #5674 ・ Take out the four screws (#5735) and five screws (#5674). #5674 ・ Open the power-wire lid. Open the power-wire lid. #5735 ・ Remove the bottom cover. Power-wire lid Bottom cover #5674...
  • Page 7 VBA15001-R.3701.A Rear cover #402-3 #403 #5424-4 #5401-7 #5425-3 #5426-3 #5427-3 #421-2 #405×2 #404×2 #448 #5429-2 #423-2 #408 #753 #1037 #5418-5 #451×2 #1016-3 #5412-1 #406-3 #413-1 #414 #452 #750 #453 #670×3 #B5431 #630×3 #5431-1 #407-2×2 #433 #5432-1 #5681×2 - Ｄ  ･ Q033 060710_...
  • Page 8 VBA15001-R.3701.A SB pop-up ・Cut the tracing film sheet, etc into the below size of piece. Then insert it into the clearance of the top cover pop-up part as shown right, and raise the SB by sliding the sheet in the direction of the arrow. Approx.2cm Approx.
  • Page 9 VBA15001-R.3701.A Discharge of Main condenser ・Discharge the main condenser from its both ends. 2KΩ/5W Be careful so that the top cover does NOT touch the discharge tool. Main condenser TOGO PCB unit TOGO PCB unit: Back ・ Disconnect the eight FPCs from the connector. ・...
  • Page 10 VBA15001-R.3701.A CCD unit ・ Take out the three screws (#631), and remove the CCD unit (#B3051-1). Caution: Some bodies have already washer(s) attached on #631×3 the mounting surface of CCD unit. #B3051-1 SB PCB Orange: Top cover ・ Unsolder the four wires (connected from Top cover).
  • Page 11 VBA15001-R.3701.A DC/DC PCB unit ・Unsolder the wire (connected from Top cover). Black: Top cover Top cover ・Take out the two screws (#5737). ・Take out the two screws (#635). ・The top cover and rubber eyecap (#B271) come off. #5737×2 △ (Revision)0~n #797×2 #B271 #796A ～...
  • Page 12 VBA15001-R.3701.A Disassembly of Top cover SB upper case 　・ Press "Pop-up lever A part" of the top cover unit so that the built-in SB is raised. Pop-up lever A part 　・ Take out two screws (#632). #632×2 ・Release the two claws. House the built-in SB and remove the SB upper case (#5301). SB upper case (#5301) Claw - Ｄ...
  • Page 13 VBA15001-R.3701.A Top cover FPC / Wiring ・Unsolder the seven wires (connected from SB lower case unit and SB release base unit). ・Remove the five solder bridges. Red: SB lower case unit Blue: SB lower case unit Green: SB lower case unit Red: SB release base unit △...
  • Page 14 VBA15001-R.3701.A SB lower case unit / SB release base unit / Buttons ・Remove the rubber SW (#382-2), ± Aperture button (#5381), and INFO button (#5383-1). ・Take out the two screws (#605), and remove [#348], [#347-1] and the release button unit (#B5350). ・Take out the screw (#650), and release the wire from the boss.
  • Page 15 VBA15001-R.3701.A Top cover FPC unit / other small parts ・Remove the three solder bridges. ・Take out the two screws (#635) and remove the top cover FPC unit (#B2007-1). ・Remove the AF/AE lock button (#5386-1) and [#387-2]. ・Take out the two screws (#635), and remove the C/D unit (#B367). ・Take out the screw (#640), and remove [#372], [#373], and mode dial unit (#B5375).
  • Page 16 VBA15001-R.3701.A SB PCB ・Unsolder the two wires (connected from Relay-PCB). Red: Relay-PCB Black: Relay-PCB DC/DC PCB ・Unsolder the two wires (connected from Mount GND plate and Frront body FPC). Black: Mount GND plate Black: Front body FPC Bottom base plate unit ・Take out the five screws (#616).
  • Page 17 VBA15001-R.3701.A Separation of Front and Rear bodies ・Take out the four screws (#624). ・Separate the front body from the rear body. Caution: Separate them slowly so as NOT to cut the two wires of the relay-PCB that pass through between the SB PCB and main condenser.
  • Page 18 VBA15001-R.3701.A 2. Rear body Remote block ・Remove SW-FPC [#B2006]. ・Take the two screws (#683). ・Remove the remote block (#158-1). #B2006 #354 #683×2 #158-1 DC/DC PCB ・Remove the five wires (connected from SB-PCB and Battery box) . ・Take out the two screws (#670). ・Remove the DC/DC PCB.
  • Page 19 VBA15001-R.3701.A SB PCB Main condenser ・Remove the two wires (yellow-circled) of the main condenser. #142 #1076 ・Remove the main condenser that is attached on with the adhesive double- #1077 coated tape. ・Take out the screw (#687). #141×2 ・Remove the SB PCB. #1043-3 Main condenser #1043-3...

  • Page 20: Front Body

    VBA15001-R.3701.A 3. Front Body Eyepiece barrel unit AE FPC unit ・Take out the screw (#607), and remove the AE FPC retainer plate (#293). ・Remove the FPC of the AE FPC unit (#B2008) from the connector. ・Take out the screw (#604), and remove the AE sensor plate spring (#285-3). ・Take out the screw (#291-1), and remove [#B2008] and [#290].
  • Page 21 VBA15001-R.3701.A Penta unit Screen areas ・Take out the two screws (#635), and remove [#201] and [#202-1]. ・Remove the hollow penta prism unit (#B4) ,which is adheved by Super X. ・Remove the finder field frame 2 (#283). ・Take out the two screws (#635), and remove the SI retaining unit (#B277). ・Remove the finder field frame 1 (#282-1).
  • Page 22 VBA15001-R.3701.A Connection-FPC ・Take out the screw (#670). ・Remove the connection-FPC (#1020) from the connector. #670 Connection-FPC (#1020) AF sensor unit ・Disconnect the AF sensor unit FPC from the connector. AF sensor unit FPC ・Take out the three screws (#162) with hexagonal wrench (φ1.5mm). The AF sensor unit (#B2163) and the three springs (#161) come off.
  • Page 23 VBA15001-R.3701.A SQ FPC ・Unsolder eight wires (connected from SQ, Fmin, and Mg). ・Remove the four solder bridges. ・Remove the SQ FPC by releasing from the bosses. SQ FPC Boss×2 Black:SQ Black:Fmin Red:Mg Solder bridge ×4 Blue:Mg Orange:Fmin Yellow:SQ Green:SQ Gray:SQ Shutter unit ・Turn the white gear in the direction of "A", and raise the mirror.
  • Page 24 VBA15001-R.3701.A In-finder LCD unit ・Take out the two screws (#683). ・Remove the in-finder LCD unit (#B2010). #683×2 #B2010 #276 #295 #758 SB SW unit ・Remove the three solder bridges. ・Remove the SB SW unit. ・Remove the front body FPC from the connector. SB SW unit (#B1012) Front body FPC Solder bridge ×3...
  • Page 25 VBA15001-R.3701.A Front body FPC SI LED-FPC ・Remove the seven solder bridges and the other four solder bridges. Solder bridge×7 Solder bridge×4 ・Remove the SI LED-FPC (#1011) and [#279]. ・Remove the front body FPC (#1009). #278×2 #1011 #279 #1009 - Ｄ  ･ Q033 060710_...
  • Page 26 VBA15001-R.3701.A Relay PCB ・Unsolder the two wires (connected from SQ PCB unit). ・Take out the screw (#607). #607 ・Remove the relay PCB. Relay PCB Red:SQ PCB unit Black:SQ PCB unit SQ PCB unit ・Take out the three screws (#638). ・Turn " ① " part in the direction of the arrow, and remove the SQ PCB unit, while releasing from the roller section.
  • Page 27 VBA15001-R.3701.A Bayonet / A/M-change SW / Lens-contact areas #621×2 #115-1 #119 #B116 #137-1 #B2113 #198 #638×2 #189 #112×3 #135-1 #607 #111 #660 #648×5 - Ｄ  ･ Q033 060710_...
  • Page 28 VBA15001-R.3701.A Aperture lever / F-min SW areas #190 #205 #206 #207-1 #203-2 #209 #210 #1106 #208-1 #639 #133-1 #204 #213 #136 #1105 #134-1 #645 #B2231 #240-4 Mirror unit #238-3 #239-2 #199×2 #236-1 - Ｄ  ･ Q033 060710_...
  • Page 29 VBA15001-R.3701.A Assembly/ Adjustment ・ NOTE: For undescribed tapes and sponges here in"Assembly", refer to PARTS LIST. 1. Front body #B2231 Mirror unit #240-4 #238-3 Be careful NOT to bend here. #239-2 #199×2 #236-1 ・ With the mirror being raised, assemble the pins and apply the adhesive (Super X) on each pin.
  • Page 30 VBA15001-R.3701.A Aperture lever F-min SW areas　 #190 Grease: LEN317A #205 #206 Grease: LEN317A #203-2 #209 #207-1 #210 #1106 #208-1 #639 #133-1 #204 #136 #213 #1105 #134-1 Black:SQ FPC #645 Orange:SQ FPC Position for hooking spring ・Hook [#205] and then [#204]. ・Hook [#213].
  • Page 31 VBA15001-R.3701.A SQ PCB unit ・ Move the roller section to the position as shown in Fig. ① . ・ Turn " １" all the way to the end in the direction of the arrow. Then, Press " ２" in the direction of "Lock". ・...
  • Page 32 VBA15001-R.3701.A Lens contacts unit #B2113 #198 #638×2 #189 Release button unit #621×2 #115-1 #119 #B116 - Ａ  ･ Q033 060710_...
  • Page 33 VBA15001-R.3701.A Bayonet Mount GND plate #137-1 #112 Grease: LEN317A #111 ・ Put [#135-1] and fix it with the screw (#607). ③ ⑤ ・ Attach [#137-1]. #135-1 #607 ② ・ Attach three pieces [#112]. ⑥ ・ Mount the bayonet (#111). #112×3 ・...
  • Page 34 VBA15001-R.3701.A Relay-PCB unit ・ Mount the relay-PCB unit (#1004-1) in the direction for positioning, and fix it with the screw (#607). ・ Arrange the wires as shown in "Fig. ① ". #607 ・ Solder the five wires (connected from SB-PCB, TOGO PCB, and SQ PCB unit). Relay-PCB Red:SB PCB Pink:TOGO PCB...
  • Page 35 VBA15001-R.3701.A ・Fold the contact-FPC down, and attach it by fitting the four bosses in the holes. ・Make seven solder bridges and four solder bridges. Solder bridge×7 Solder bridge×4 Contact-FPC In-finder LCD unit ・Fix the in-finder LCD unit (#B2010) with the two screws (#683). #683×2 #B2010 #276...
  • Page 36 VBA15001-R.3701.A Shutter unit ・Turn the white gear in the direction of "A", and raise the mirror. ・Mount the shutter unit (#31), and fix it with two screws (#635). ・Turn the white gear in the direction of "B", and let the mirror down. ・Attach [#757].
  • Page 37 VBA15001-R.3701.A AF sensor unit ・Put three springs (#161) and mount the AF sensor unit [#B2163]. ・Turn three screws (#162) with #B2163 Hexagonal wrench (φ1.5mm) in ③ ② ① the order from all the ① ③ #162×3 way lightly to the end, then give each two-turns counterclockwise.
  • Page 38 VBA15001-R.3701.A Penta unit Screen areas ・Mount SI (#13-1). ・Mount the finder field frame 1 (#282-1). ・Attach the in-finder display prism (#9). ・Mount the SI-retaining unit (#B277) and fix it with two screws (#635). ・Mount the finder field frame 2 (#283). ・Mount the hollow penta (#B4).
  • Page 39 VBA15001-R.3701.A Eyepiece barrel unit AE FPC unit ・Mount the eyepiece barrel unit (#B261), and fix it with two screws (#638). ・Put the AE sensor adjusting-spring [#290] and AE FPC unit [#B2008], then fix them with the screw (#291-1). ・Put the AE sensor plate-spring (#285-3), and fix it with the screw (#604). ・Connect the FPC of the AE FPC unit (#B2008) to the connector.
  • Page 40 VBA15001-R.3701.A Angle inspection and adjustment of Main mirror and sub-mirror ＊ Device: 1.Main mirror 45° inspection and adjustment 2.Sub-mirror 47.75° inspection and adjustment ① Collimator (J19110) ① Collimator (J19110) ② Reflection mirror (J18362) ② 47.75° mirror tool (J61218) ③ Optical parallel (J18037-2) ③...
  • Page 41 VBA15001-R.3701.A 2. Rear body Battery box #607×3 #157×3 DC/DC lug plate Buzzer unit Backup battery #607 Battery box DC/DC lug plate Eyelet ring unit Other small parts ・Put the DC/DC lug plate (#159-1) at the final stage, then fix the battery box with the four screws (#615). #B145×2 #694×2 #694×2...
  • Page 42 VBA15001-R.3701.A SB PCB ・Mount the SB-PCB, and fix it with the screw (#687). ・Solder the two wires (connected from DC/DC-PCB) and put them in the groove for arrangement. ・Adhere the main condenser with the adhesive double-coated tape by putting in the direction for positioning. ・Solder the two wires (yellow-circled) of the main condenser.
  • Page 43 VBA15001-R.3701.A DC/DC PCB ・Mount the DC/DC-PCB, and fix it with two screws (#670). ・Put the wires in the groove for arrangement, and solder five wires (connected from SB-PCB and Battery box). #670×2 Groove Blue: Battery box (ID) Red: Battery box (+) Black:SB-PCB Black: Battery box (-) Red:SB-PCB...
  • Page 44 VBA15001-R.3701.A 3. Mounting of Front body on Rear body Mount the front body on the rear body ・Pass the wires of the relay-PCB through behind the main condenser, and assemble the front body into the rear body. SB-PCB ・Tighten four screws (#624). Main condenser #624×4 Do NOT let wires...
  • Page 45 VBA15001-R.3701.A Inspection and Adjustment of Body back "0" positioning of the dial gauge ＊ 0" position of D40 Surface plate ① Put the tool (J18001-1) on the surface plate, and set the dial gauge to "0". ② Turn the index ring in the direction of the arrow, and set to the scale "8 from "0"...
  • Page 46 VBA15001-R.3701.A DC/DC PCB ・Solder the two wires (connected from Mount GND plate and Front body FPC). Black: Mount GND plate Black: Front body FPC SB PCB ・Solder the two wires (connected from Relay-PCB). Red: Relay-PCB Black: Relay-PCB サービス 計画課 Ｍ Changed page (Overall revision) - Ａ...
  • Page 47 VBA15001-R.3701.A Assembly of Top cover Top cover FPC unit / other small parts ・Fix [#322], [#B317], shoe base (#316), and [#318-1] with four screws (#654). ・Fix the mode dial unit (#B5375), [#373], and [#372] with the screw (#640). ・Fix the C/D unit (#B367) with two screws (#635). ・Attach [#387-2] and AF/AE lock button (#5386-1).
  • Page 48 VBA15001-R.3701.A SB lower case unit / SB release base unit / Buttons ・Mount the SB lower case unit (#B2302). ・Arrange the wire (#1070-1) as shown below. ・Mount the top cover FPC unit (#B2007-1), and fix it with two screws (#635). ・Make three solder bridges.
  • Page 49 VBA15001-R.3701.A ・While pressing the SB case rotating shaft (#306-1), attach the SB-up spring (#305-1) by pushing it in the attach the SB-up spring (#305-1) by pushing it in the direction of the arrow, then fix it with the screw (#733). #305-1 #733 #306-1...
  • Page 50 VBA15001-R.3701.A AF-assist illuminator unit ・Mount the AF-assist illuminator unit (#B325-1), and fix it with the screw (#608). ・Solder the two wires (connected from AF-assist illuminator unit). #608 AF-assist illuminator unit (#B325-1) Black : AF-assist illuminator unit Uncoated wire: AF-assist illuminator unit Top cover FPC / Wiring ・Make five solder bridges.
  • Page 51 VBA15001-R.3701.A SB upper case ・Mount the SB upper case (#5301) on the SB lower case unit. SB upper case #5301 Claw SB lower case unit ・Press the pop-up lever A part of the top cover unit, and raise the built-in SB. Pop-up lever A part ・Tighten two screws (#632).
  • Page 52 VBA15001-R.3701.A When the AE-CCD positioning is adjusted, solder the only four wires that connected from the top cover to SB-PCB. Then, make a temporary assembly without mounting the rubber eye- cap (#B271), and assemble up to Page A25. Top cover ・Mount the rubber eyecap (#B271).
  • Page 53 VBA15001-R.3701.A CCD unit ・Mount the CCD unit (#B3051-1) by following the direction for positioning, and fix it with three screws (#631). Caution: #631×3 Some bodies have already washer(s) attached on #B3051-1 the mounting surface of CCD unit. Direction for positioning TOGO PCB unit ・Connect the harness.
  • Page 54 VBA15001-R.3701.A Adjustment of AE CCD positioning WARNING 警告 Take extra care not to get an electric shock when detaching 内部に高電圧部あり。カバーを外す時は感電に注意すること。 covers. After removing covers, b e sure to discharge the main カバーを外した後は、修理指針の指示に従ってメインコンデン condenser according to the instructions of repair manuals . サーの放電を必ず行うこと。...
  • Page 55 VBA15001-R.3701.A Standard →　Reference screw #B2008Metering FPC unit X-direction　→　a: Screw #291 Y-direction　→　b: Screw Y-direction (b) #741 tightening Ｘ -direction (a) Ｘ -direction (a) tightening loosening Adhesive: Screwlock Y-direction (b) loosening Discharge of Main condenser ・ Discharge currents from both terminals of the main condenser. 2KQ/5W Main condenser...
  • Page 56 VBA15001-R.3701.A Covers ・Assemble the front cover unit (#B5024) together with the Fmin coupling block (#131). #5610×2 Adhesive: Super X #B5024 #5074 #670 #5120 #626 #5610×2 #29-2 #131 #26-2 Gap adjustment of SB lighting unit ・In case the result is out of standard, pop the SB unit up and make an adjustment by turning the adjusting dial with Hexagonal wrench.
  • Page 57 VBA15001-R.3701.A Rear cover #402-3 Direction for positioning #403 #5424-4 #5401-7 #5425-3 #5426-3 #5427-3 #421-2 #405×2 #404×2 #448 #5429-2 Direction for positioning #423-2 #408 #1037 #5418-5 #1016-3 #451×2 #5412-1 #406-3 #413-1 #414 #452 #750 #453 #670×3 #B5431 #630×3 #5431-1 #407-2×2 #433 #5432-1 #5681×2 - Ａ...
  • Page 58 VBA15001-R.3701.A Rear cover (continued) ・Connect the TFT-PCB connection-FPC to the connector. ・Mount the rear cover. ・Tighten four screws (#5690) and two screws (#5618). #5618×2 △ (Addition) #5690×4 Rear cover TFT-PCB connection-FPC サービス 計画課 Ｍ - Ａ 30 ･ Feb.05.2007 Changed page　△×１ Q033 060710_...
  • Page 59 VBA15001-R.3701.A Accuracy inspection and adjustment (Camera body) ★ : New tool (except Image unit) USB cable: UC-E4 To USB terminal Stabilized power source（Set value ＝ 7.4V 　0.3Ω　5.0A） ＋ D40 battery tool (J61219) or AC adapter (EH-5) ＋ Power connector (EP-5) ★...
  • Page 60 VBA15001-R.3701.A D40 Inspection and Adjustment Software (J18416) This inspection and adjustment software runs on Windows. Install the software by following the below procedure. <Operating environment> Check the following operating environment which is required for installing this program on PC. IBM PC/AT compatible Windows XP Professional Edition, Windows XP Home Edition, Windows2000, Pentium II 300MHz ～...
  • Page 61 VBA15001-R.3701.A <Procedure for installation> The file (PD40.EXE) of this program is provided via FD or e-mail. Because this is the self-extracting file, decompress the file before installing, and follow the next procedure. 1. Create a folder for install under any name in any drive. 　　(e.g.）C: ￥D40 2.
  • Page 62 VBA15001-R.3701.A 3. Double-click on the pasted file to display the following screen. Press the OK button, then decompression starts. 4. When the decompression of file is finished, the file (D40.exe) is created. 5. The install is completed. - Ａ  ･ Q033 060710_...
  • Page 63 VBA15001-R.3701.A < Procedure for installing USB driver > If this program is used by the USB interface, installing the USB driver is necessary. But if the OS is "Windows XP", the driver is already preloaded so it is not necessary to install it. 1.
  • Page 64 VBA15001-R.3701.A <Start-up of Program> 1. Double-click the file (D40.exe), then Inspection and adjustment program for D40 starts. 2. To display in Japanese, select the radio button "JAPANESE" in "LANGUAGE" in the lower right-hand corner of the screen. 　However, this is not properly viewed in the English OS. When the "Version"...
  • Page 65 VBA15001-R.3701.A AE inspection and adjustment 《USB connection communication》 ① AE CCD alignment inspection and adjustment (ref. Page A26, A27 for details） ② AE accuracy inspection and adjustment ③ Aperture accuracy inspection ④ Adjustment for battery check level [Use the D40 battery tool (J61219) and stabilized power supply.] ⑤��...
  • Page 66 VBA15001-R.3701.A Bottom cover ･ Mount the bottom cover. ・ Fix it with four screws (#5735) and five screws (#5674). #5674×2 #5674 #5674 #5735 △ (Addition) Bottom cover #5735 #5674 Grease：MZ-00S #5735×2 ∞ Infinity focus inspection & adjustment ・ Replace the finder screen with the infinity focus adjustment screen (J15410), and use the reference lens (J18010) and read the value.
  • Page 67 VBA15001-R.3701.A Necessary adjustments when parts are replaced 1. D40 adjustment software and updates Built-in SB Writing of AE CCD accuracy Aperture Battery light volume accuracy 　　　　Adjustments EEPROM positioning inspection & accuracy check volt- inspection & inspection & fixed adjustment adjustment inspection age level adjustment...
  • Page 68 VBA15001-R.3701.A 2. Shooting image adjustment software and Software updates Writing Writing Sensi- Gr/Gb com- Sensitiv- Pixel Pixel of TFT Factory 　　　Adjustments of fixed tivity fixed default pensation ity ratio defect defect values values setting adj. (R/B com- compen- filter) pensa- sation - Replacement tion -...
  • Page 69 VBA15001-R.3701.A Shooting Image Adjustment 1. Summary When D40 shooting image-related and listed parts on Page A40 are replaced, be sure to make an adjustment by the shooting image adjustment software for D40 (J65094). The details of its function and how to use this software are as follows: 2.
  • Page 70 VBA15001-R.3701.A 6. Basic usage 　(1) Execute "D40IMG.exe" to start up the main screen. (ref. Fig.1) 　(2) Select ENGLISH / JAPANESE in Language to display any menu. (ref. Fig.2) 　(3) Click the button to start adjustments. ※ When the adjustments from ① to ⑤�� are made, calculate to get the reference values ( ⑥�� ) by using the reference body beforehand, then perform the adjustments.
  • Page 71 VBA15001-R.3701.A 7. Required equipment and conditions ※ AC adapter EH-5, Power connector (EP-5) and USB cable (mini B type) UC-E4 are used for all adjustments so they are not specified in the list. ★ New tool Item Required device Setting/Remarks 1 Sensitivity adjustment Luminance LV13 equivalent ・5100K color viewer　　...
  • Page 72 VBA15001-R.3701.A 8. Summary 　The summary on each adjustment is as follows: ① Sensitivity adjustment 　 Camera is faced to the color viewer of LV13 equiv. with ND filter (-6 steps) being put between them, and the adjustment is made by changing the ampgain so that G output can fall in the standard range. The gain value is adjusted so that the G output average value (Average of Gr/Gb) in the center (300×300 pixels) can reach the target output level (approx.
  • Page 73 VBA15001-R.3701.A 　⑦ Factory default setting 　　This selects and sets the language and video mode at the time of shipping products. 　⑧ Checking of adjustment value The adjustment value is confirmed, functioning as substitute for the traditional "READING AND REWRITING OF EEPROM DATA.". 　⑨...
  • Page 74 VBA15001-R.3701.A 9. Procedure 9-1. TOGO PCB adjustment 　● Calculate the "Sensitivity" and "Sensitivity ratio" reference values by using D40 reference body beforehand, then perform the adjustments. (ref. 9-4.) 　● For shooting image adjustment, make all items from ① to ③ . The adjustments from ① through ③ are all programmed to be executed in serial order.
  • Page 75 VBA15001-R.3701.A 　[・Attach the tool lens (Aperture F5.6) and SP1 (B filter) to the camera.] 　・Get the camera closest to the center of the illuminated surface of the color viewer. 　・Click "OK". 　・The adjustment starts. When it is completed, the next conditions are displayed. 　・Attach the tool lens (Aperture F5.6) and SP3 (R filter) to the camera.
  • Page 76 VBA15001-R.3701.A 9-3. ⑤�� Compensation - white point 　 Check the environmental temperature (approx. 20-25°C). 　・ 　・Click "Start". 　・Setting conditions are indicated. 　・Cap the camera with the body cap or lens cap to shield light from the mount. 　・Click "OK". 　・When the adjustment starts, pixel defects are detected, displaying the number of pixels and addresses. 　・When it is completed, "OK"...
  • Page 77 VBA15001-R.3701.A 　Flicker adjustment 　・Usually default value is set and adjustment is not necessary. 　・If flicker is recognized by visual check, adjust by the slider so that no flicker is visible. 　・Remove the USB cable from the camera, then remove the AC adapter without turning the camera OFF. 　...
  • Page 78 VBA15001-R.3701.A ＜ Measurement of Consumption current value ＞ When this camera is used for measuring the consumption current value, connect the power connector (EP-5) and install wiring as follows for the measurement. 7.8V 0.3Ω － ＋ ＋ － Ａ ※ EP-5 ※...
  • Page 79 VBA15001-R.3701.A レリーズ SW-FPC 上カバー FPC ｼｬｯﾀｰﾕﾆｯﾄへ SI LED-FPC TO SHUTTER UNIT RELEASE SW-FPC TOP COVER FPC 黒 BLACK 絞り PI-FPC 赤 RED 赤 RED 被覆なし UNCOATED APERTURE PI-FPC 青 BLUE POP-UP MG 青 BLUE レンズ接点 FPC 黒 BLACK △ ( 訂正 ) LENS CONTACT FPC △...
  • Page 80 VBA15001-R.3701.A Inspection standards Items Judgment standard Remarks External view Step Between top cover and apron: 0.2 mm or less Visual check (height difference) Other parts: 0.3 mm or less; Inside elements must not be seen. Digital micrometer Moving parts: 0.5 mm or less Clearance from Top cover to Apron;...
  • Page 81 VBA15001-R.3701.A Items Judgment standard Remarks AF accuracy Center:0 ± 4 mrad Others: 0 ± 2 mrad Special tool Brightness box Pitch Center: 0 ± 5 mrad Others: 0 ± 0 mrad Difference btwn vertically and horizontally (center): 45μm or Def amount less AF-assist illuminator Lighting level...
  • Page 82 VBA15001-R.3701.A Items Judgment standard Remarks Viewfinder In-finder LCD Tilt from finder screen: 1°or less Visual check position Tilt: (Right-left tilt from the lower part of finder field frame): Shoot the finder 90’ or less field frame with Finder field frame ±...
  • Page 83 VBA15001-R.3701.A Items Judgment standard Remarks Standby / consumed Main SW / OFF: 200μA or less (when inner battery is fully Power source: 7.8V current Luminance: EV2 charged) Lens: Main SW / ON (Half-release timer: OFF): 200μA or less (when 8-55/3.5-5.6G inner battery is fully charged) Oscilloscope: Main SW / ON (Half-release timer: ON): 200μA or less (when...
  • Page 84 VBA15001-R.3701.A 工　具・TOOLS　 ★：新規設定工具・NEW　TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others J15428 AE CCD 位置出し工具 FOR D80 AE CCD positioning tool J15410 無限合致調整用スクリーン FOR D70,D70s,D50 Infinity focus adjustment screen J18362 反射ミラー FOR D70,D70s,D50 Reflection mirror J18416 Ｄ４０調整用ＦＤ　ＩＢＭ３． ５ Adj.fd for D40 (IBM 3.5) ★...
  • Page 85 VBA15001-R.3701.A ★：新規設定工具・NEW　TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others J19110 小型バック出しコリメータ　 Back focus collimator J61218 サブミラー位置だし工具（Ｄ４０） Sub mirror inspection tool(D40) ★ J18037-2 オプチカルパラレル Optical parallel J18004 絞りレバー高さ点検工具 Aperture lever positioning gauge J19004-1 インジケータ及びスタンド （ボディバック台、ゲージ） Dial indicator and Stand J18001-1 ボディバック出し工具...
  • Page 86 VBA15001-R.3701.A ★：新規設定工具・NEW　TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others ＡＦ５０／１． ４Ｄ J18267 Lens AF50/1.4D J61185 撮像関係調整用レンズ FOR D1,D2H,D70,D70s,D50 D1 Standard lens D200 J18191 ＮＤフィルタ－８Ｘ ２枚使用 ND filter 8X It uses by two pieces 　　　　　　　　 FOR D2H,D70,D70s,D50.D200 J63070 カラービューア Color Viewer J63068 輝度計（BM-3000）...
  • Page 87 VBA15001-R.3701.A ★：新規設定工具・NEW　TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others OS-30MF ドライサ－フ　ＯＳ－３０ＭＦ DRY SURF OS-30MF(OIL BARRIER) OS-30MF(OIL BARRIER) LEN317A グリース　ＬＥＮ３１７Ａ G����� ������� ����� ������� ������� EDB0011 ネシ゛ロック（赤）1401C Screw lock 1401C C-8008B セメダイン　８００８（黒） Cemedain 8008(BLACK) MZ-800S ドライサ－フ　ＭＺ－８００Ｓ DRY SURF MZ-800S 汎用品...

This manual is also suitable for:

Vba15101D40