Operating Heater - Comfort Glow CGD3018P Owner's Operation And Installation Manual

OPERATING
HEATER
Manually-Controlled Models
FOR YOUR SAFETY
READ BEFORE
LIGHTING
WARNING: If you do not fol-
low these instructions exactly, a
fire or explosion may result caus-
ing property damage, personal
injury or loss of life.
A. This appliance has a pilot which must
be lighted by hand. When lighting the
pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all
around the appliance area for gas. Be
sure to smell next to the floor because
some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL
GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor's phone. Follow
the gas supplier's instructions.
• If you cannot reach your gas sup-
plier, call the fire department.
C. Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn
by hand, don't try to repair it, call a
qualified service technician or gas
supplier. Force or attempted repair
may result in a fire or explosion.
D. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been un-
der water.
104341
LIGHTING
INSTRUCTIONS
WARNING
• If fireplace has glass doors,
never operate this heater with
glass doors closed. If you op-
erate heater with doors closed,
heat buildup inside fireplace
will cause glass to burst. Also
if fireplace opening has vents
at the bottom, you must open
the vents before operating
heater.
• You must operate this heater
with a fireplace screen in place.
Make sure fireplace screen is
closed before running heater.
NOTICE: During initial operation
of new heater, burning logs will
give off a paper-burning smell.
Orange flame will also be present.
Open damper or window to vent
smell. This will only last a few hours.
Note: Homeowners generally prefer to
operate their heater with the chimney
damper closed. This will put all the
heat into the room. However there may
be times you will desire the full flames
of the Hi heat setting but will find the
heat output excessive. You can open the
chimney damper (if you have one) fully
or partially to release some of the heat.
WARNING: Damper handle
will be hot if heater has been
running.
1. STOP! Read the safety information
in column one.
2. Make sure manual shutoff valve is
fully open.
3. Press in and turn control knob clock-
wise to the OFF position.
Clockwise
Control Knob
Ignitor Button
Figure 31 - Control Knob and Ignitor
Button Location
17
OWNER'S MANUAL
4. Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow "B" in the safety in-
formation above. If you don't smell
gas, go to the next step.
5. Slightly depress and turn control
knob counterclockwise
the PILOT position. Press in control
knob for five (5) seconds (see Page 20).
Note: You may be running this
heater for the first time after hook-
ing up to gas supply. If so, the con-
trol knob may need to be pressed in
for 30 seconds. This will allow air to
bleed from the gas system.
6. With control knob pressed in, press
and release ignitor button. This will
light pilot. The pilot is attached to the
burner. If needed, keep pressing ig-
nitor button until pilot lights.
Note: If pilot does not stay lit, con-
tact a qualified service person or gas
supplier for repairs. Until repairs are
made, light pilot with match. To light
pilot with match, see Manual Light-
ing Procedure, page 18.
7. Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob.
Note: If pilot goes out, repeat steps
3 through 7. If control knob does not
pop out when released, contact a
qualified service person or gas sup-
plier for repairs.
8. Slightly depress and turn control
knob counterclockwise
desired heating level. The burner
should light. Set control knob to any
heat level between HI and LO.
WARNING: Do not operate
heater between PILOT and HIGH
positions.
Thermopile
HI
PILOT
OFF
LO
Figure 32 - Pilot
to
C-clockwise
to
C-clockwise
Pilot Burner
Ignitor
Electrode
Thermocouple
Continued