Table of Contents
Advertisement
T
roubleshooting
Heater indicator light
does not illuminate
Possible causes
1.
The power is not turned ON
2.
The portable spot cleaner is not attached completely
Reduced Spray or No Spray
Possible causes
1.
Formula & water tank may be empty
2.
Formula & water tank may not be seated completely
3.
Pump may have lost prime in portable spot cleaning mode
4.
The portable spot cleaner is not attached completely
DirtLifter
PowerBrush does not turn
®
Possible causes
1.
The portable spot cleaner is not attached completely
2.
The unit is in the upright position
3.
Circuit breaker on machine (if equipped) may have tripped
4.
The belt is off or broken
Loss of suction power
Possible causes
1.
Tanks may not be seated properly
2.
Nozzles may not be assembled properly
3.
The portable spot cleaner is not attached completely
4.
Dirty tank has picked up maximum amount of
dirty water and has reached full line
5.
Formula & water tank is empty
6.
Suction Gate is open.
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
For any questions or concerns, BISSELL is happy to be of
service. Contact us directly at 1-800-237-7691.
16
w w w . b i s s e l l . c o m
WARNING:
to reduce the risk of fire,
electric shock or injury, unplug
from the outlet before servicing.
Remedies
1. The power must be ON to activate the heater indicator light
2. Make sure the portable spot cleaner is attached
Push down firmly to check (see pages 6 or 12 for
detailed instructions)
Remedies
1. Refill tank
2. Turn power OFF. Remove and reseat tank
3. Hold end of hose below water level in tank to prime
4. Push down firmly to check connection
Remedies
1. Make sure the portable spot cleaner is attached.
Push down firmly to check (see pages 6 or 12 for
detailed instructions)
2. Brushes only rotate when unit is reclined using the
recline pedal
3. Turn the machine OFF and unplug from outlet. Check
to see if foreign object is caught in brush roll. Remove
object. Plug machine in to reset circuit breaker
4. Turn power OFF and unplug unit from outlet. Follow
instructions on pages 14 and 15
Remedies
1. Pick up both tanks and reseat them so it they fit snugly
on the unit
2. Unplug the unit. Check to make sure the "lip" of the
nozzle cover is securely hooked into the groove on the
top of nozzle (see page 10)
3. Make sure the portable spot cleaner is attached.
Push down firmly to check (see pages 6 or 12 for
detailed instructions)
4. Empty dirty tank
5. Check fluid levels in formula & water tank
6. Check to make sure the suction gate is closed. Follow
"Cleaning Suction Gate" instructions on page 13.
8 0 0 . 2 3 7 . 7 6 9 1
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the LIFT-OFF Deep Cleaner and is the answer not in the manual?
Questions and answers
will not **** up water properly
The Bissell LIFT-OFF Deep Cleaner may not be picking up water properly for the following reasons:
1. Tank not seated properly: Ensure both tanks are picked up and reseated so they fit snugly on the unit.
2. Nozzle not assembled correctly: Verify the nozzle cover's "lip" is securely hooked into the groove at the top of the nozzle.
3. Portable spot cleaner not attached completely: Check that the portable spot cleaner is firmly attached by pushing it down completely.
4. Dirty tank is full: Empty the dirty tank if it has reached the maximum fill line.
5. Formula and water tank is empty: Check the fluid levels in the formula and water tank and refill if necessary.
6. Suction gate is open: Ensure the suction gate is closed by following the instructions in the manual.
If none of these steps resolve the issue, contact BISSELL Consumer Care for further assistance.
This answer is automatically generated