Omit 24Hr Zones; Reinstate 24Hr Zones; Set Chime Areas; Turning Chime On And View Act. Faults - Texecom Premier 888 User Manual

The Arming Menu

Omit 24Hr Zones

It is possible to exclude (omit) or include 24Hr zones whilst
the system is disarmed to allow access to an area. Users
with access to this function can only omit zones that have
been programmed as 'Omittable'.
➤ To omit 24Hr zones, proceed as follows:
.... ....
.... ....
Enter a valid User code
should look like this:
!"#$"%#&'()#)"
*+,#-$-).,/
) )
) )
Press until the display looks like this:
!"#$"%#&'()#)"
D,1)#78E+#F"(.-
# # # #
Press , the display will look something like this:
F"(.#553#A.>%+.
?+"()#!""+#####X
... ... ... ...
Enter a zone number
to search, the display will look something like this:
F"(.#53:#A.>%+.
U'>O#!""+######X
!
If the zone can be omitted, there will be a 'Star' to
the right of the zone number. Only zones that have
the 'Omit' attribute assigned to them can be omitted.
3 3 3 3
Press to omit the selected zone, the display will look
something like this:
F"(.W53:#A.>%+.
1-#D,1)).<
!
A 'Star' will appear to the left of the zone number to
indicate that the zone has been selected for omitting.
Repeat for other zones.
When all the required zones have been selected for omitting
/ / / /
press , the display should look like this:
!"#$"%#&'()#)"
IJ1)#K.(%/
# # # #
Press , the display will look something like this:
W#F"(.-#D,1)).<#W
#M%.#54#K'+#7553
The selected 24Hr zones are now omitted.

Reinstate 24Hr Zones

To reinstate the omitted zones, simply follow the instructions
3
again. However, when the
look something like this:
F"(.W53:#A.>%+.
1-#_")#D,1)).<
16
, the display
) ) ) )
or use the key
F"(.W53:#A.>%+.
U'>O#!""+######X
key is pressed, the display will
F"(.W53:#A.>%+.
U'>O#!""+######X
Premier 888 & 8168 User Manual

Set Chime Areas

When a zone is enabled for Chime the Keypad will
generate a Chime tone every time the zone is activated.
Users with access to this function will be able to turn
Chime on and off for selected areas.
Zones within an area can be individually programmed for
chime in Edit Chime Zones (see page 23 for details).
➤ To set Chime areas, proceed as follows:
.... ....
.... ....
Enter a valid User code
should look like this:
!"#$"%#&'()#)"
*+,#-$-).,/
& & & &
Press , the display will look something like this:
I('P@.#BC1,.#"(
##X#WWW99999#\
! ! 1 1
! ! 1 1
Use keys - to select/deselect areas i.e.
0 *
and = Areas A, B and C, the display will look
something like this:
I('P@.#BC1,.#"(
##X#*UB99999#\
!
Only areas that have been programmed for 'Chime'
can be selected. A 'Star' means the area can be
selected and a 'Dot' means the area cannot be
selected.
2
Pressing will select/deselect all areas.
%
Pressing will toggle between areas A to H and
I to P (Premier 8168 only).
When all the required areas have been selected for
# # # #
'Chime' press , the display should look like this:
!"#$"%#&'()#)"
A.)#BC1,.#*+.'-/
( ( ( (
Press to exit the menu and return to normal.
Turning Chime On and Off
The display will normally show the time & date.
##0+.,1.+#2342
38684958N#M%.#54
➤ To turn Chime On, proceed as follows:
& &
& &
Press , the keypad will chime to indicate that Chime
is now enabled.
➤ To turn Chime Off, proceed as follows:
& &
& &
Press , the keypad will bleep to indicate that Chime is
now disabled.
, the display
!
,
INS177