Related Manuals for Kleenmaid lwg74
Summary of Contents for Kleenmaid lwg74
- Page 1 Automatic Washers W001C W001C Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. 38910R7 May 2004...
-
Page 3: Table Of Contents
Table of Replacement Parts ................Installation................... Contents Dimensions and Specifications............. Before You Start ................... Tools ....................Electrical ..................Water....................Installing the Washer ................Step 1: Remove the Shipping Brace and Shipping Plug....Step 2: Wipe Out Inside of Washtub ..........Step 3: Connect Water Inlet Hoses .......... - Page 4 Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 38910...
-
Page 5: Replacement Parts
Replacement Parts If replacement parts are required, contact the source from which you purchased your washer. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 38910... - Page 6 Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 38910...
-
Page 7: Installation
Installation Dimensions and Specifications 71,1 cm (28 in.) 1,02 cm (0,4 in.) 65 cm 66 cm W519I (25,6 in.) (26 in.) W519I * With leveling legs turned into base. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 38910... -
Page 8: Before You Start
Installation Before You Start Electrical Refer to serial plate for specific electrical Tools requirements. For more detailed information, refer to For most installations, the basic tools you will need section on Electrical Requirements. are: Water Washer needs two standard 19,05 mm (3/4 inch) water supply faucets with a pressure between 138 and 827 kPa (20 to 120 pounds per square inch). -
Page 9: Installing The Washer
Installation Installing the Washer NOTE: Do not tilt washer to front or sides when moving. NOTE: If the washer is delivered on a cold day The shipping brace and plug should be saved and must (below freezing), or is stored in an unheated room be reinstalled whenever washer is moved or or area during the cold months, do not attempt to transported to a new location. -
Page 10: Step 3: Connect Water Inlet Hoses
Installation Step 3: Connect Water Inlet Hoses NOTE: Refer to section on Water Supply Requirements before connecting water inlet hoses. The appliance is to be connected to the water mains using new hose-sets and old hose-sets should not be reused. Turn on the water supply faucets and flush the lines for approximately two minutes to remove any foreign materials that could clog the filter screens in the inlet... -
Page 11: Step 4: Connect Drain Hose To Drain Receptacle
Installation Step 4: Connect Drain Hose to Drain Standpipe Installation Receptacle Place the adapter into the standpipe. Remove the drain hose from its shipping position on Remove the beaded tie-down strap from accessories the rear of the washer by unhooking the hose from the bag and place around standpipe and drain hose, retainer clamp. - Page 12 Installation High Standpipe Installation Low Standpipe Installation Place the adapter into the standpipe. Remove the No. 562P3 Siphon Break Kit is required for this type beaded tie-down strap from accessories bag and place of installation. This kit is available (as optional around standpipe and drain hose, approximately 30 cm equipment at extra cost) through an authorized dealer (12 inches) down from the top of pipe and tighten strap...
-
Page 13: Sink Installation
Installation Sink Installation In the Wall Installation For this type of installation, use the beaded tie-down For installations of this type, the drain hose MUST be strap (supplied in accessories bag), or use a large wire secured to one of the inlet hoses using the beaded tie- tie (available from your local hardware store) and down strap from accessories bag. -
Page 14: Step 5: Position And Level The Washer
Installation Laundry Tub Installation Step 5: Position and Level the Washer For this type of installation, the drain hose MUST be Position washer so it has sufficient clearance for secured to the stationary tub to prevent hose from installation and servicing. dislodging during use. -
Page 15: Step 6: Plug In The Washer
Installation Step 6: Plug In the Washer Step 8: Check Lid Switch Refer to section on Electrical Requirements, and plug Washer should stop spinning when lid is opened. the washer in. W376IE0C Figure 15 W504SE3B W504SE3B Step 9: Check Installation Figure 13 Refer to Installer Checklist on the back cover of this Step 7: Add Water to the Washer... -
Page 16: Electrical Requirements
Installation Electrical Requirements WARNING (240 Volt, 50 Hertz with 3 Prong Earthing Plug) Improper connection of the equipment- earthing conductor can result in a risk of NOTE: The wiring diagram is located in the electric shock. Check with a qualified control hood. -
Page 17: Water Supply Requirements
Installation Water Supply Requirements Water Temperature Cold: WARNING Recommended cold water temperature is 10° to 24° Celsius (50° to 75° Fahrenheit). Under certain conditions, hydrogen gas may be produced in a hot water system that Hot: has not been used for two weeks or more. Recommended hot water temperature is 60°... -
Page 18: Water Pressure
Installation Water Pressure Pressure must be a minimum of 138 to a maximum of 827 kPa (20 to 120 pounds per square inch) static pressure measured at the faucet. NOTE: For water pressure over 827 kPa (120 pounds per square inch) we recommend the installation of a pressure limiting valve (Part Number PSL50DK). -
Page 19: Information For Handy Reference
Information for Handy Reference Date Purchased Model Number Serial Number Store Name Store Address Phone Number Service Agency Service Agency Address Phone Number NOTE: Record the above information and keep your sales slip. Model and serial numbers are located on the nameplate. Customer Care Centre and Information: 1300 652 100... - Page 20 Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 38910...
-
Page 22: Installer Checklist
Installer Checklist Fast Track for Installing the Washer (Refer to the manual for more detailed information) • Remove the • Position and LEVEL LEVEL Shipping Brace Level the D255I D255I and Shipping Washer. Plug. CHECK CHECK TLW521N D316I W316I • Wipe Out Inside •...
Need help?
Do you have a question about the lwg74 and is the answer not in the manual?
Questions and answers