Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kleenmaid KAW793
Summary of Contents for Kleenmaid KAW793
- Page 1 USA. yuiop Installation Instructions For Model KAW793 Automatic Washer DR073I DR073I KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. (If the washer changes ownership, be sure this manual accompanies the washer.) Part No. 37005R1 1/95 37005...
-
Page 2: Table Of Contents
Important Safety Instructions ............... 3 Table of Roughing In Dimensions ............... 5 Before Installing ..................5 Contents Tools Needed ................... 5 Agitator ..................... 5 Positioning and Levelling the Washer ..........6 Shipping Brace ..................6 Motor Overload Protector ..............6 Electrical Requirements ................ -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS (Save These Instructions) WARNING 9. Do not repair or replace any 14. ALWAYS disconnect the To reduce the risk of fire, part of the washer, or attempt washer from electrical supply electric shock, serious any servicing unless before attempting any service. - Page 4 21. Loading door MUST BE 24. Never operate the washer NOTE: The WARNING AND CLOSED any time the washer with any guards and/or IMPORTANT SAFETY is to agitate or spin. DO NOT panels removed. INSTRUCTIONS appearing in this by-pass the loading door manual are not meant to cover all switch by permitting the 25.
-
Page 5: Roughing In Dimensions
Roughing In Dimensions . . . 28" (71.12 cm) 7/16" (11.11 mm) 25-5/8" (65.09 cm) 26" (66.04 cm) W173IS3B With Leveling Legs Turned Into Base Before Installing . . . Agitator Tools Needed For most installations, the basic The agitator should not be UTILITY KNIFE tools you will need are: removed except for service. -
Page 6: Positioning And Levelling The Washer
Installing the Washer . . . Positioning and Shipping Brace Levelling the Washer The shipping brace should be saved and must be used (to Place rubber feet on all four prevent damage to washer levelling legs. components), whenever washer is moved or transported to a new Place washer in position on a location. -
Page 7: Electrical Requirements
Electrical Service . . . NOTE: The wiring diagram is DO NOT OPERATE OTHER WARNING located in either the control hood, APPLIANCES ON THE SAME Improper connection of the or on the backside of the washer CIRCUIT. DO NOT OVERLOAD equipment-grounding front panel. -
Page 8: Water Supply
Water Supply . . . Water Temperature WARNING NOTE: Water supply faucets should be readily accessible to Under certain conditions, Cold: permit turning them off when hydrogen gas may be Same as cold water supply. washer is not being used. produced in a hot water (Recommended cold water system that has not been... - Page 9 Water Inlet Hose Connections IMPORTANT: Connect the white Install water inlet hoses as IMPORTANT: Thread hose colored hose coupling end of inlet follows: couplings onto valve connections hoses (with screened washers) to finger-tight, then 1/4 turn with 1. Remove the two screened water supply taps.
-
Page 10: Drain Facilities
Drain Facilities Drain Hose Follow the instructions outlined in IMPORTANT: The drain hose NOTE: The washer is shipped this manual for installing the installation is a very important from the factory with the drain curved end of the drain hose into factor in the washer installation. -
Page 11: Low Standpipe Installation
Installations . . . Standpipe Installation TIE-DOWN Place washer in its location. STRAP Place only the smooth end of the DRAIN HOSE drain hose into the standpipe. DO SLEEVE NOT, under any circumstances, place any ribbed portion of the 12" drain hose into the standpipe! (30.489 IMPORTANT: Drain receptacle... -
Page 12: Sink Installation
Sink Installation DRAIN HOSE For this type of installation, use the beaded tie-down strap (supplied in accessories bag), or use a large wire tie (available from your local hardware store) and secure the drain hose to the cabinet top hinge, see illustration. This will prevent the drain hose TIE-DOWN from dislodging during use. - Page 13 37005...
- Page 14 37005...
- Page 15 37005...
-
Page 16: Information For Handy Reference
Information for Handy Reference . . . Kleenmaid P.O. Box 36 Brookvale, NSW 2100 Australia Date Purchased Serial Number Model Number Phone Number Dealer's Name Phone Number Dealer's Address Service Agency Service Agency Address Record the above information and keep your sales slip. Model and serial numbers are located on the nameplate.
Need help?
Do you have a question about the KAW793 and is the answer not in the manual?
Questions and answers