Manual Channel Set - JVC HR-S5700AM Instructions Manual

SELECT TV SYSTEM
5
Press PUSH JOG %fi to
place the pointer next to
the appropriate TV system,
then press OK or PUSH
JOG .
Auto Channel Set will
start.
AUTO CH SET
PLEASE WAIT
START
RETURN TO NORMAL
SCREEN
6
Press MENU.
NOTE:
If you perform Auto Channel Set when the aerial cable is not
connected properly, "SCAN COMPLETED -NO SIGNAL-"
appears on the screen in step 5. When this happens, make sure
of the aerial connection and press OK; Auto Channel Set will
take place again.
IMPORTANT
If no sound accompanies the picture or the audio sounds
unnatural on some channels that have been stored by
Auto Channel Set, the TV system setting for those
channels may be incorrect. Select the appropriate TV
system for those channels.
When you see the picture but the audio can't be heard or
sounds unnatural" on page 49.
Since your video recorder memorizes all detected
stations even if the reception condition is poor, some of
those stored stations may produce a noisy picture. To
delete those stations,
Major Countries
Australia, New Zealand, Kuwait, U.A.E.,
Indonesia, Singapore, Thailand, Malaysia,
Iran, Saudi Arabia, Egypt, Morocco,
Lebanon, Iraq
China, Mongolia, Russia
Hong Kong
U.S.A., Japan, S.Korea, Taiwan
TV SYSTEM SELECT
B/G
D/K
I
M
[5/ ∞ ] =
[MENU] : EXIT
CH FRQ SYS CH FRQ SYS
01 150 BG 07 229 BG
02 165 BG 08 237 BG
03 195 BG 09 355 BG
04 205 BG 10 365 BG
05 213 BG 11 374 BG
06 221 BG 12 384 BG
FINISH [5/ ∞ ] = [ ] : DELETE
[5/ ∞ ] =
: EDIT
[MENU] : EXIT
"TV System Selection –
"Delete A Channel" on page 48.
TV System
B/G
D/K
I
M

Manual Channel Set

Store channels that were not stored during Auto Set Up (
or Auto Channel Set ( pg. 46).
ACCESS TUNER SET
SCREEN
1
Perform steps 1 – 3 of "Auto Channel Set" on page 46.
ACCESS CHANNEL LIST
2
Press PUSH JOG %fi to place the pointer next to "CH
EDIT", then press OK or PUSH JOG
SELECT POSITION
3
Press PUSH JOG %fi to place the pointer next to an
open channel position, then press OK or PUSH JOG
SELECT BAND
4
Press PUSH JOG %fi to place the pointer next to the
band of your choice, then press OK to initiate Manual
Channel Set.
BAND SELECT
VHF L
VHF H
UHF
[5/ ∞ ] =
[MENU] : EXIT
SET DESIRED STATION
5
The screen to the right
appears when a station is
detected.
If you do not want to store
the detected station...
Press PUSH JOG %fi to
place the pointer next to
"CONTINUE", then press
OK or PUSH JOG
Channel search will resume.
If you want to store the detected station...
Press PUSH JOG %fi to place the pointer next to
"STORE", then press OK or PUSH JOG
List appears again.
The blueback screen and the TV picture currently
being broadcast appear alternately for 8 seconds each.
If you want to store another channel, repeat steps 3 – 5.
When channel search completes for that band, the
Band Select screen appears again. To set channels for
other bands, select another band and start Manual
Channel Set again (
For fine tuning adjustment, see "Fine-Tuning
Channels" on page 49.
RETURN TO NORMAL
SCREEN
6
Press MENU.
EN
.
MANUAL CH SET
PLEASE WAIT
VHF L 100MHZ
[MENU] : EXIT
STORE
CONTINUE
[ 5 /∞] =
[MENU] : EXIT
.
. The Channel
step 4 and 5).
47
pg. 8)
.