Download Print this page

Comnet NetWave NW8 Quick Start Manual

Industrial outdoor 802.11a/b/g/n dual radio wireless ethernet

Advertisement

Quick Links

This manual serves the following
ComNet Model Numbers:
NW8
NW8E
QUICK START GUIDE
INDUSTRIAL OUTDOOR 802.11A/B/G/N
DUAL RADIO WIRELESS ETHERNET
Thank you for purchasing NetWave
walk you through installation.
This guide applies to the following models:
NW8: Industrial Multipoint, FCC Version, User Configurable
NW8E: Industrial Multipoint, ETSI Version, User Configurable
An easy to read LED array displays unit operational status along with received signal
strength for Radio 1 ensuring optimal installation and operation. See Figure 2 on
Page 2 for LED Indicator explanations.
See Figures 3 through 6 beginning on Page 3 for mounting instructions.
from ComNet. This quick start guide is designed to
®
INS_NW8_NW8E_QS_REV– 05/20/13 PAGE 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the NetWave NW8 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Comnet NetWave NW8

  • Page 1 QUICK START GUIDE INDUSTRIAL OUTDOOR 802.11A/B/G/N DUAL RADIO WIRELESS ETHERNET Thank you for purchasing NetWave from ComNet. This quick start guide is designed to ® This manual serves the following walk you through installation. ComNet Model Numbers: This guide applies to the following models:...
  • Page 2 FIGURE 2 – STATUS LED INDICATIONS VISUAL CUE INDICATION SOLID GREEN Power is supplied to the NW8/NW8E POWER No power is supplied to the NW8/NW8E FLASH GREEN Ethernet connection is established SOLID YELLOW Ethernet connection is established and there is activity present ETHERNET / RSSI2 RSSI Level is >...
  • Page 3 IEC plug into the socket of the PIM. PoE power input: Passive PoE (range 48 to 57 VDC) The NW8[E] can also be powered by a suitable IEEE 802.3af/at PSE device such as a PoE switch or the included CNGE1IPS injector.
  • Page 4 Determine the correct cable type and length needed to connect the NetWave device to your antenna (antenna and cables not included). The NetWave NW8 and NW8E have N Female connectors to attach the external antenna cables to. Step 2. Press down firmly on the N Male connector of the antenna cable and tighten.
  • Page 5: Installation Requirements

    • Wireless mode – Set to AP or Client • Country code – Only required if setting up the NW8E (ETSI) model NOTE: It is the user’s responsibility to ensure that the correct country is chosen. ComNet accepts no liability for incorrectly set up equipment.
  • Page 6 QUICK START USER GUIDE NW8/NW8E TYPICAL REDUNDANT RING TOPOLOGY APPLICATION PoE+ CNGE1IPS or any PSE device Ethernet PoE Camera PoE+ NWADA1 External Directional Antenna NWADA1 External Directional Antenna ComNet Gigabit STP Blocked Managed Switch Port 1Gbps providing 30W PoE Ethernet...
  • Page 7: Default Configurations

    QUICK START USER GUIDE NW8/NW8E TYPICAL DROP-AND-REPEAT TOPOLOGY APPLICATION 24VAC IP Camera CNGE1IPS Ethernet Ethernet PoE+ CNGE1IPS or any PSE device PoE+ NWADA1 External Directional Antenna Ethernet 1Gbps Ethernet PoE+ PoE Camera NWAVBSA1 Building or Other Obstacle ComNet Gigabit External Antenna...
  • Page 8: Agency Compliance

    QUICK START USER GUIDE NW8/NW8E AGENCY COMPLIANCE Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: •...
  • Page 9 T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | INFO-EUROPE@COMNET.NET © 2015 Communications Networks Corporation. All Rights Reserved. “ComNet,” the “ComNet Logo,” “NetWave,” and the “NetWave Logo” are registered trademarks of Communication Networks, LLC. INS_NW8_NW8E_QS_REV– 05/20/13 PAGE 9...

This manual is also suitable for:

Netwave nw8e