Dbs Receiver Multi-Brand Remote Control; Cable Box Multi-Brand Remote Control - JVC HR-J440U Instructions Manual

36
EN
CABLE/DBS
MBR SET
1
¶
STOP
DBS Receiver Multi-Brand
Remote Control
The VCR's remote control can control functions on the brands
of DBS (Direct Broadcast Satellite) receivers listed below.
TURN ON THE DBS RECEIVER
1
Turn the power on using the DBS receiver's remote
control.
ENTER DBS RECEIVER BRAND
2
While holding down CABLE/DBS on the VCR's remote
control, press MBR SET and use the NUMBER keys to
enter the DBS receiver brand number from the chart
below and then press STOP.
Follow the example shown at bottom right.
Once you have set the remote control to operate the
DBS receiver, you don't have to repeat this step until
you replace the remote control's batteries.
OPERATE DBS RECEIVER
3
First, while hoding down CABLE/DBS, press POWER to
see if the DBS receiver's power goes off as it should. If
it does, try other functions.
To operate your DBS Receiver, while holding down
CABLE/DBS, press the corresponding button:
POWER, CH 5 ∞, NUMBER keys (or ENTER).
Depending on the DBS receiver you may have to
press ENTER after having pressed the NUMBER keys.
NOTES:
Depending on the type of DBS receiver, there may be cases
where some or all functions cannot be operated using the
remote control.
Though ECHOSTAR has a number of different remote codes,
this remote control is applicable only to one of those codes
preset at the factory.
DBS BRAND NAME
RCA (DSS)
SONY (DSS)
PRIMESTAR
ECHOSTAR
POWER
1 2 3
NUMBER
4 5 6
7 8 9
0
CH
3 ¡
7 8
4 ¢
BRAND CODE
80
81
90
91
SPECIAL FEATURES (cont.)
Cable Box Multi-Brand
Remote Control
The VCR's remote control can control functions on the brands
of cable boxes listed below. Some cable box brands have more
than one code. If your cable box does not function with a
specified code, try other codes.
TURN ON THE CABLE BOX
1
Turn the power on using the cable box's remote control.
ENTER CABLE BOX BRAND
2
While holding down CABLE/DBS on the VCR's remote
control, press MBR SET and use the NUMBER keys to
enter the cable box brand number from the chart below
and then press STOP.
Follow the example shown below.
Once you have set the remote control to operate the
cable box, you don't have to repeat this step until you
replace the remote control's batteries.
OPERATE CABLE BOX
3
First, while holding down CABLE/DBS, press POWER
to see if the cable box's power goes off as it should. If it
does, try other functions.
To operate your cable box, while holding down
CABLE/DBS, press the corresponding button:
POWER, CH5 ∞ , NUMBER keys (or ENTER).
For some brands of cable box, you must press ENTER
after having pressed the NUMBER keys.
NOTE:
Depending on the type of cable box, there may be cases where
some or all functions cannot be operated using the remote control.
CABLE BOX BRAND NAME
CURTIS
GEMINI
GENERAL INSTRUMENTS
HAMLIN
JERROLD
OAK
PANASONIC
PIONEER
RCA
REGAL
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
TELEVIEW
TOCOM
VIDEOWAY
ZENITH
(Ex.) To set remote control to cable box brand RCA 24:
2
MBR SET
CABLE/DBS
Hold
Press in succession
down
BRAND CODE
09, 10
08
01, 02, 03, 04, 05, 06, 07, 08
15, 16, 17, 18
01, 02, 03, 04, 05, 06, 07, 08
19, 20, 21
24, 25, 26
13, 14
24, 25, 26
15, 16, 17, 18
08, 13
09, 10
19, 20, 21
08, 13
24, 25, 26
08, 13
22, 23
11, 12
11, 12
4 7
STOP
Release