Hilti TE 6-A36 Operating Instructions Manual page 12

f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5.1.5 Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together
may cause burns or a fire.
d) Under abusive conditions, liquid may be ejec-
ted from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
5.1.6 Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
5.2 Additional safety precautions
5.2.1 Personal safety
a) Wear ear protectors. Exposure to noise can cause
hearing loss.
b) Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
c) Hold power tool by insulated gripping surfaces
when performing an operation where the fastener
may contact hidden wiring or its own cord.
Fasteners contacting a "live" wire may make ex-
posed metal parts of the power tool "live" and
could give the operator an electric shock.
d) Always hold the power tool securely with both
hands on the grips provided. Keep the grips dry,
clean and free from oil and grease.
e) Breathing protection must be worn if the power
tool is used without a dust removal system for
work that creates dust.
f) Improve the blood circulation in your fingers by
relaxing your hands and exercising your fingers
during breaks between working.
g) Avoid touching rotating parts. Switch the power
tool on only after bringing it into position at
the workpiece. Touching rotating parts, especially
rotating insert tools, may lead to injury.
h) Activate the safety lock (forward / reverse switch
in the middle position) before storing or trans-
porting the power tool.
i) When restarting after the electronic overload
protection system has switched the tool off, care
must be taken to ensure that the power tool
is held securely with both hands on the grips
provided.
j) Children must be instructed not to play with the
appliance.
k) The appliance is not intended for use by chil-
dren, by debilitated persons or those who have
received no instruction or training.
l) Dust from material such as paint containing lead,
some wood species, minerals and metal may be
harmful. Contact with or inhalation of the dust
may cause allergic reactions and/or respiratory
diseases to the operator or bystanders. Certain
kinds of dust are classified as carcinogenic such
as oak and beech dust especially in conjunction
with additives for wood conditioning (chromate,
wood preservative). Material containing asbestos
must only be treated by specialists. Where the
use of a dust extraction device is possible it
shall be used. To achieve a high level of dust
collection, use a suitable vacuum cleaner of the
type recommended by Hilti for wood dust and/or
mineral dust together with this tool. Ensure that
the workplace is well ventilated. The use of a
dust mask of filter class P2 is recommended.
Follow national requirements for the materials
you want to work with.
5.2.2 Power tool use and care
a) Secure the workpiece. Use clamps or a vice
to secure the workpiece. The workpiece is thus
en
7