In these operating instructions, the designation “the Always keep these operating instructions power tool” always refers to the TE 6-A36 cordless together with the power tool. rotary hammer. Ensure that the operating instructions are...
2. Description 2.1 Use of the product as directed The TE 6-A36 is a hand-held, cordless rotary hammer for hammer drilling in concrete and masonry, drilling in steel and wood and driving or removing screws. Use only the batteries and chargers recommended by Hilti.
Page 8
Do not use the battery as a power source for other unspecified appliances. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance.
2.10 Li‑ion battery charge status LEDs light constantly LEDs blink Charge status C C ≧ 75 % LED 1,2,3,4 50 % ≦ C < 75 % LED 1,2,3 25 % ≦ C < 50 % LED 1,2 10 % ≦ C < 25 % LED 1 LED 1 C <...
Power tool TE 6‑A36 Speed under no load in hammer drilling mode 1,040/min Single impact energy 2.0 J NOTE The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
Page 11
reference. The term “power tool” in the warnings mask, non-skid safety shoes, hard hat, or hearing refers to your mains-operated (corded) power tool or protection used for appropriate conditions will battery-operated (cordless) power tool. reduce personal injuries. c) Prevent unintentional starting. Ensure the switch 5.1.1 Work area safety is in the off‐position before connecting to power source and/or battery pack, picking up or carrying...
Page 12
To achieve a high level of dust collection, use a suitable vacuum cleaner of the 5.2.1 Personal safety type recommended by Hilti for wood dust and/or a) Wear ear protectors. Exposure to noise can cause mineral dust together with this tool. Ensure that hearing loss.
held more securely than by hand and both hands 5.2.4 Electrical safety remain free to operate the power tool. b) Check that the insert tools used are compatible with the chuck system and that they are secured in the chuck correctly. Before beginning work, check the working area 5.2.3 Cordless tool use and care (e.g.
Hilti batteries intended for use with this 6.2 Charging the battery power tool, i.e. B 36/3.0 Li‑ion, B 36/2.4 Li‑ion, B 36/2.6 Li‑ion, B 36/3.3 Li‑ion or B 36/3.9 Li‑ion. 1. Push the battery into the power tool from the rear until it is heard to engage with a double click.
Page 15
3. Check that the sealing lip of the dust shield is 1. Set the forward / reverse switch to the middle clean and in good condition. Clean the dust shield position or remove the battery from the power if necessary or replace it if the sealing lip is found tool.
3. Bring the side handle into the desired position For reverse rotation, push the forward / reverse switch and check that it is fitted correctly and secured. on the side of the power tool toward the grip in the 4. Fit the battery. direction of the arrow.
(e.g. with Hilti grease. It is essential that the dust shield at a window) as this has an adverse effect on battery is replaced if the sealing lip is found to be damaged.
Page 18
The battery runs down more Battery condition is not optimal. Have battery condition diagnosed quickly than usual. by Hilti Service or replace with a new battery. The battery doesn’t engage The retaining lugs on the battery are Clean the retaining lugs and check dirty.
Dispose of the batteries in accordance with national regulations or return them to Hilti. Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling.
12. EC declaration of conformity Hilti Corporation Designation: Cordless rotary hammer Type: TE 6-A36 Year of design: 2009 We declare, on our sole responsibility, that this product complies with the following directives Jan Doongaji Dietmar Sartor and standards: until 28.12.2009 98/37/EC, as of...