Table of Contents
Advertisement
Recording Features
Record one programme while watching another
— Select channel to watch
Once recording is in progress, all you need to do is to set the
channel controls on the TV for the station you wish to view.
The programme selected with the TV's channel controls appears
on the TV screen while the one selected with the PR +/– buttons
is recorded on the tape.
Elapsed recording time indication
You can check the exact time of a recording.
A
Set counter display
Press – –:– – until a counter reading appears on the display panel.
By pressing the – –:– – button, you can change the display to
show the counter reading, channel position*, clock time or tape
remaining time.
* Channel position is not displayed during playback.
B
Reset counter
Press 0000 before starting recording or playback.
The counter is reset to "0:00:00" and shows the exact elapsed
time as the tape runs.
Instant Timer Recording (ITR)
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-min. increments), and shuts the recorder off after
recording is finished.
A
Start recording
Press 7 on the recorder.
B
Engage ITR mode
Press 7 again. "o" blinks and 0:30 appears on the front display
panel.
C
Set recording duration
If you want to record for more than 30 minutes, press 7 to extend
the time. Each press extends recording time by 30 minutes.
NOTE:
You can only perform ITR using the 7 button on the recorder's
front panel.
Tape Remaining Time
— Display remaining time
Press – –:– – until the time remaining on the tape appears.
The display panel shows the tape remaining time with "– –:– –"
displayed.
By pressing the – –:– – button, you can change the display to
show the counter reading, channel position*, clock time or tape
remaining time.
* Channel position is not displayed during playback.
NOTE:
Depending on the type of tape used, there may be times when the
tape remaining time reading may not appear right away, or is not
correct. "– –:– –" may sometimes appear, or the display may blink
on occasion.
Super VHS ET (S-VHS ET)
— Recording on VHS cassettes with S-VHS quality
You can record in SP mode on VHS cassettes with S-VHS picture
quality. You can play back a tape recorded using the S-VHS ET
function on most of S-VHS recorders and of VHS recorders
equipped with SQPB (S-VHS QUASI PLAYBACK) function. (Notice
some recorders are not compatible with the S-VHS ET function.)
You can activate the S-VHS ET function only before you start
recording on a VHS cassette.
Before recording, make sure that "B.E.S.T." is set to "ON"
(
15).
Engage the S-VHS ET mode.
Press S-VHS ET on the recorder. You can check the current setting
("S-VHS ET : ON" or "S-VHS ET : OFF"). If "S-VHS ET : OFF"
appears on the TV screen, press S-VHS ET again in about 5
seconds to set it to "ON".
The S-VHS indicator lights up on the front display panel.
NOTES:
You cannot activate the S-VHS ET function...
... while recording is in progress.
... while timer-recording or Instant Timer Recording (
progress.
... while B.E.S.T. (
The S-VHS ET function does not work...
... with S-VHS cassettes.
... with recordings in LP/EP mode.
To keep the highest quality recording and playback pictures
over a long period of time, S-VHS recording on S-VHS cassettes
is recommended .
Use of high grade tapes is recommended for S-VHS ET
recordings. On some tapes, picture quality will not improve
even if the S-VHS ET function is used. Check the recording
quality before you start important recordings.
While playing back a tape recorded using the S-VHS ET function
on some recorders, noise may appear. (If playback picture
becomes blurred or interrupted, use a cleaning cassette.)
In the high-speed search, still, slow-motion or frame-by-frame
playback modes (
performed frequently on a tape recorded using the S-VHS ET
function, the tape may be damaged and the picture may be
deteriorated.
— 9 —
15) is in progress.
6), noise may appear. If these modes are
9) is in
Advertisement
Table of Contents
