How To Use - Maclaren techno xlr User Manual

EN
Instructions
IMPORTANT: • READ THESE INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THEM FOR FUTURE REFERENCE.
• YOUR CHILDREN'S SAFETY MAY BE AFFECTED IF YOU DO NOT FOLLOW THESE INSTRUCTIONS.
1 TO OPEN THE bUGGY
A Release storage clip.
B Open out the buggy.
C Using foot, push the footplate down fully to engage the primary lock.
CAUTION: Ensure that all locking devices are engaged before use.
2 TO OPERATE bRAKES
A TO ENGAGE BRAKES: With foot, pull the brake levers fully back.
B TO RELEASE BRAKES: Push the brake levers fully forward.
CAUTION: Parking device shall be engaged during the loading and unloading of children.
CAUTION: Ensure parking device is engaged before leaving the buggy unattended.
3 TO OPERATE FRONT WHEEL SWIVEL LOcKS
A TO LOCK SWIVELS: Lift BOTH swivel locking levers.
B TO UNLOCK SWIVELS: Push down BOTH swivel locking levers.
4 SEAT bELT/SHOULDER HARNESS OPERATION
WARNING:
INJURY FROM FALLING OR SLIDING OUT.
ALWAYS USE THE cROTcH STRAP IN
cOMbINATION WITH THE WAIST bELT AND
SHOULDER STRAPS.
TO FIT HARNESS:
A Pull shoulder straps over the childs shoulder then attach to the waist clips by
sliding strap loops onto the hooks.
B I nsert both waist clips into the clasp, shoulder straps are secured once the clips are
fastened.
C Adjust strap lengths by sliding buckles. Belt and harness should be snug.
TO RELEASE HARNESS:
D Press the button on both the front and back of the clasp simultaneously to release.
5 TO FIT HEAD HUGGERS
Unclip shoulder straps from seat belt clasp and feed straps through holes
in head hugger fabric (height can be adjusted by selecting upper or lower holes).
Reclip shoulder straps to seat belt clasp.
TO FIT HARNESS PADS
A Lay open pad under shoulder harness strap.
B Fold pad over and secure Velcro® strips.
6 TO ATTAcH THE SEAT LINER
A Unclip all shoulder and waist straps.
B Feed crotch strap, waist straps and shoulder harness straps through
holes in liner.
C Fasten the Velcro® to the back of the seat
Reverse this procedure to remove the seat liner for washing
Follow the washing instructions on the care label attached to the seat liner.
Dry thoroughly before refitting to the buggy.
The buggy will fold with the seat liner in place.
7 TO OPERATE THE ADJUSTAbLE LEGREST
A Raise leg rest.
B Push in the lever on the leg rest to lock.
C To release, simply pull the lever back on base of adjustable leg and allow
the leg rest to return.
8 TO ADJUST SEAT REcLINE
A
TO RECLINE THE SEAT: Position your hand on the seat recline lever. Gently lift the
recline lever with your fingers whilst taking the weight of the seat back with your
hand. Still maintaining support and holding the lever, gently recline the seat back in
to the desired position. Release seat recline lever when seat back is in desired
position, ensuring both sides lock at the same time.
AVOID SERIOUS
B TO RAISE SEAT BACK: From rear of buggy push seat back to original upright or
desired intermediate position.
9 TO ADJUST HANDLE LENGTHS
A Press triggers.
B Slide handles until triggers locate in one of 3 positions. Release triggers to lock.
10 TO ATTAcH THE HOOD
CAUTION: Overloading may cause a hazardous unstable condition to exist.
Maximum total capacity of hood pockets - 1.1 lb (0.5 kg).
A With buggy open clip the hood to the handle tubes just above the retaining blocks.
B Wrap Velcro® strips around handle tubes.
C Place rear apron behind seat back
D Extend hood and press down on side hinges to lock open.
TO TILT HOOD:
E Fully unzip back panel.
F Tilt hood forward.
G The hood is removed by firmly pressing down the clip release tabs.
11 TO FIT THE RAIN APRON
A Return hood to non-tilted position before fitting rain apron.
B Ensure visor is folded away beneath the hood.
C Place the apron over the hood front.
D Attach two eyelets (one each side) to the hood clips.
E Attach the two eyelets (one each side) to the front legs.
12 TO FIT THE SHOPPING bAG
CAUTION: Overloading may cause a hazardous unstable condition to exist.
Maximum load 4.4 lb (2 kg) evenly distributed.
The buggy may be folded with the bag still attached but all contents must be removed.
Failure to do this could damage buggy and contents of shopping bag.
A Place bag on the 'X' frame under seat with lowest edge of bag at front.
B Attach front straps to front legs just below seat.
C Attach rear straps to rear legs just above horizontal tie bar.
13 TO FOLD THE bUGGY
Ensure visor is folded away beneath the hood.
Ensure the seat back is in its fullest upright position and the hood (if fitted) is folded
back. Remove contents of shopping bag.
It is recommended that the harness is fastened before folding the buggy.
A Using foot, lift up on footplate to release primary lock.
B Push down on secondary lock lever.
C Grip handles and push forward.
D Compress folded buggy and engage the storage clip.
14 REMOVING AND REFITTING THE SEAT cOVER
Remove hood, shoulder pads and seat retention straps from buggy if fitted.
A Twist shoulder strap end buckles and feed through holes.
The waist harness back strap is fixed to the chassis behind the seat.
B
To remove, twist the buckles on each end of the harness back strap and
unthread from the 'D' rings attached to the chassis.
IMPORTANT – It is important that the strap be rethreaded through the 'D'
rings after the seat has been refitted. Failure to do so will endanger your child.
C Feed crotch strap buckle through holes.
D Unclip seat cover retaining straps.
E Unfasten seat fabric from handle tubes and seat base.
F Slide fabric from seat back and base.
G When refitting seat fabric, insert seat back support tubes into fabric flap.
H W hen refitting shoulder straps choose the fabric holes appropriate to the child's
size. Twist the buckles and feed through seat cover, seat back and then through
holes in plastic seat back arms.
J When refitting seat fabric to seat base pass crotch strap buckle through the
hole in the seat fabric and then hole in seat base.
3