Chapter 1 Introduction The SRP-2110 digital receiver is fully compliant with the inter- national Digital Video Broadcasting (DVB) standard, and thus is able to receive digital broadcasts of that standard. For its operation you need an antenna, which must be installed ap- propriately.
2 Introduction • Can store up to 10,000 television and radio services. • You can edit the services list. • Can create lists of your favourite services. • Can view information about the current television or ra- dio programme. • Has an electronic programme guide that provides an overview of scheduled programmes.
1.2 Controlling the digital receiver 3 using the digital receiver, you should keep it plugged into a wall socket to be in standby mode so that it can run timer events at any time. 1.2.1 Front panel The front panel of the digital receiver has buttons to control the digital receiver, specific lights and a display to indicate its status.
Page 10
4 Introduction There is a USB port on the front panel for firmware update and data transfer.
1.2 Controlling the digital receiver 5 1.2.2 Remote control button switches the digital receiver between standby mode and active mode. mutes the sound. Press again to switch it back on. £ ¢ ¡ switches the remote control to television mode to operate your television.
Page 12
6 Introduction next service. £ ¢ ¡ displays the services list. See §5.2.1 for more details. It is also used to select a menu item. Navigation buttons are used to navigate in menus or to change values for menu options. £...
1.2 Controlling the digital receiver 7 £ ¢ ¡ switches the output of the TV SCART socket over be- tween the digital receiver and the device connected to the VCR SCART socket. See §4.2.4 for more details. £ ¢ ¡ displays the satellites list with their services list.
Page 14
8 Introduction You can operate the digital receiver with the wire- less keyboard as well as the remote control. To be able to use the keyboard, you should plug the keyobard receiver into a USB port on the digital receiver. To see the keyboard map, press the F10 key on the keyboard on the live television screen.
1.3 Common Interface 9 1.3 Common Interface There are pay TV services available; these are accessible with the use of a Conditional Access Module (CAM) and a subscription card. A Common Interface (CI) is the slot into which you can insert a CAM. The front of the digital receiver has two common interface slots.
Page 16
10 Introduction that is able to descramble two pay services simultaneously. §5.6 for the picture-in-picture feature.
Chapter 2 Setup 2.1 Unpacking Before going any further, check that you have received the fol- lowing items with the digital receiver. • Remote control • Wireless keyboard with USB receiver • Four batteries for the remote control and wireless key- board (AAA 1.5 V) •...
Page 18
12 Setup socket. For the power consumption of the digital re- ceiver, refer to Table 2.1. • The wall socket should be near the equipment. Do not run an extension lead to the unit. • The mains plug shall remain readily operable so that it can be removed easily to disconnect the power.
firmly fixed. 3. Turn upside down the digital receiver. 4. Do it with the bottom cover in the same way. 2.3 Rear panel connections The SRP-2110 has a wide range of connections on the back.
Page 20
14 Setup Check what connections your television set has in comparison with the digital receiver. LNB 1 IN Satellite broadcasting signal input socket for the first tuner (Current: Max.500mA with overload pro- tection) LNB 1 OUT Satellite broadcasting signal output socket through the first tuner LNB 2 IN Satellite broadcasting signal input socket...
2.4 Connecting up your digital receiver 15 USB port for firmware update and data trans- ON/OFF Power switch (You have to turn on this switch first to use this digital receiver.) Table 2.3: Connectors specifications HDMI High definition video output Left &...
16 Setup 2.4.1 Connecting to the antenna Whatever sort of connection you have be- tween the digital receiver and the television, you need to connect the digital receiver to the antenna so that it can receive digital televi- sion broadcasts. Connect the antenna ca- ble to the LNB 1 IN connector on the back panel of the digital receiver.
2.4 Connecting up your digital receiver 17 and send them to the digital receiver. However, the satellite antenna only sends the frequencies that it can catch with the LNB frequency and polarisation specified by the digital re- ceiver. So if you have linked from the LNB 1 OUT connector to the LNB 2 IN connector, you would have some limitations in using some features such as dual recording.
Page 24
18 Setup To use the SCART output For best results with a standard television set, you should use a SCART cable. Plug one end of the cable into the TV socket on the digital receiver, and plug the other end into a free SCART socket on your television.
Page 25
2.4 Connecting up your digital receiver 19 To use the Composite video output You need to obtain a Composite video cable (RCA cable) to use the Composite video out- put. Plug one end of the cable into the VIDEO (yellow) socket on the digital receiver, and plug the other end into the matching socket on your television.
20 Setup 2.4.3 Connecting to your video recorder The digital receiver can also output video through an auxiliary SCART connector to another device such as a video recorder. You need to obtain a SCART cable to link the auxiliary SCART connector. Plug one end of the cable into the VCR socket on the digi- tal receiver, and plug the other end into the matching socket on your video recorder or...
Page 27
2.5 Switching on for the first time 21 CAUTION If the digital receiver no longer reacts properly to the remote control commands, the batteries may be flat. Be sure to re- place only with 1.5 V AAA size batteries, and observe the following precautions.
22 Service Search Chapter 3 Service Search After connecting up the digital receiver, you will need to per- form a service search. NOTE If there is no service stored, you will be not able to access all menus. A is another name for a . 3.1 Searching for broadcasting services This digital receiver can be operated with both fixed antenna and motorized antenna.
3.1 Searching for broadcasting services 23 3.1.1 Configuring LNB settings There are two large frequency bands for satellite broadcasts. One is C band which ranges approximately from 4 to 6 GHz. The other is K band which ranges approximately from 12 to 18 GHz.
Page 30
24 Service Search 1; otherwise, set it to Tuner 2. If you have connected the LNB 1 OUT and LNB 2 IN with a loop-through cable, then set the Connection Type option to Loop Through; otherwise, set it to Separated. NOTE Both the LNB 1 IN and LNB 2 IN sockets should be connected to your antennas either directly or via the loop-through ca-...
3.1 Searching for broadcasting services 25 Set the DiSEqC 1.0 option and the DiSEqC 1.1 option accord- ing to your antenna configuration. For example, to select the antenna con- nected to the A5 input in the left figure, set the DiSEqC 1.1 option to 2 of 4 and the DiS- EqC 1.0 option to 1 of 4.
26 Service Search following steps: 1. Choose your desired satellite at the Satellite Name op- tion. 2. Select the tuner that is connected to the motorized an- tenna at the Tuner Select option. 3. Set the DiSEqC Command Mode option to User. 4.
Page 33
3.1 Searching for broadcasting services 27 To use the USALS protocol, se- lect the Installation > USALS Setting menu. You should see a screen like the left figure. At first you have to set the Motor- ized DiSEqC 1.3 option to En- able.
28 Service Search 3.1.4 Searching for services To perform a service search, se- lect the Installation > Searching menu. You should see a screen like the left figure. There are in general four service search methods: • searching every service of a satellite, •...
Page 35
3.1 Searching for broadcasting services 29 To avoid such missing, you had better set the Search Mode item to Blind. With the Blind mode, the digital receiver tries to search every service, scrutinizing every transponder with every possible combination of transponder elements. It thus may require many minutes or even many hours.
Page 36
30 Service Search NOTE You may get transponder information from a satellite maga- http://www.satbeams.com http: zine or website such as //www.lyngsat.com. Searching single service of a transponder To search single service of a transponder, take the following steps: 1. Choose your desired satellite at the Satellite Name op- tion.
3.2 Copying services 31 2. Set the Search Mode option to SMATV, and then press £ ¢ ¡ button to diaply additional options. 3. Choose your desired transponder at the Frequency op- tion or enter it with the numeric buttons. 4.
32 Service Search 3.3 Editing the transponder list If you failed to receive services of a transponder because it consists of wrong data, you can solve it by correcting the data. Select the Installation > SAT/TP Edit menu. To change the data of a trans- ponder, take the following steps: 1.
3.4 Resetting to factory settings 33 3.4 Resetting to factory settings The digital receiver maintains the following data: • Satellite list • Services list • Favourite list • Timer list • Preference settings You can reset all data of the digital receiver. Select the Instal- lation >...
Page 40
You can edit the channel data on your computer by using a channel editor software, Vega, which is available from Top- http://www.i-topfield.com/eng/download/ field’s website, utility_list.asp. With Vega you can do the following:...
3.6 Clearing the services list 35 • Adding, deleting or modifying transponder entries • Deleting or modifying service entries • Adding, deleting or modifying favourite groups As to how to use Vega, refer to its user guide, which is accom- panied by the software.
36 Preference Settings Chapter 4 Preference Settings 4.1 Language settings You can select the language in which the menu will be dis- played. In addition to that, you can select the language of audio track and of subtitle track. Select the Settings >...
4.1 Language settings 37 4.1.2 Subtitle language Set the 1st Subtitle Language option and the 2nd Subtitle Lan- guage option to your desired languages. When you watch a programme, if the programme has a subtitle track of the lan- guage that is specified for the 1st Subtitle Language, it will be displayed.
38 Preference Settings 4.2 Video and audio settings You have to configure the video and audio settings appropriately for your television set and other devices. Select the Settings > A/V Output menu. You should see a screen like the left figure. 4.2.1 High definition television The digital receiver supports various video resolutions from 576 to 1080.
4.2 Video and audio settings 39 button. Whenever you press it, the video resolution is changed in turn. NOTE You can enjoy only standard definition video with the fol- lowing video outputs: • Composite video output (VIDEO) • SCART output (TV) 4.2.2 Television aspect ratio If you have a wide-screen television, set the TV Aspect Ratio option to 16:9.
40 Preference Settings You cannot fully enjoy wide-screen programmes with your normal-screen television as the above figures show. The left figure shows a normal picture displayed in the normal screen. To watch wide-screen programmes in the shape like the cen- tre figure, set the Display Format option to Letter Box.
4.3 Local time setting 41 device since the digital receiver is just a bypass for the video recorder. 4.2.5 Audio mode Basically, there are two audio sources as you can find two audio sockets on the back panel of the digital receiver. You can enjoy only one source or both of them in either stereo or mono.
Page 48
42 Preference Settings Settings > Time Select the menu. You should see a screen like the left figure. You can set the clock manually or use the time signal, Greenwich Mean Time (GMT), carried as part of the digital television broadcast. To use Greenwich Mean Time, take the following steps: 1.
Page 49
4.3 Local time setting 43 NOTE Daylight saving time adds one hour to the time when the op- tion is set to On. When setting the time offset from Green- wich Mean Time, make sure that time offset does not include daylight saving time.
44 Preference Settings 4.4 Parental control In general, television programmes are classified according to the level of violence, nudity and language of their content. When you are watching a programme, you can check its pro- gramme classification on the information box. For the infor- mation box, see §5.2.3.
4.5 To use MediaHighway programme guide 45 Time item is set to Locked, you have to enter the PIN when accessing the Time menu. If you enter a wrong number, you cannot use the menu. To release a locked item, set it to Un- locked.
46 Preference Settings 4.6 Options for recording To set the options for recording, select the Settings > Recording menu. You should see a screen like the left figure. To enable the time-shift function, you should set the Time Shift- ing option to anything other than Disable. The available range for this option is 30 minutes to 5 hours.
4.7 Options for playback 47 4.7 Options for playback To set the options for playback, select the Settings > Playback menu. You should see a screen like the left figure. If you want to play back a recorded file from beginning, set Starting Position option to Beginning.
48 Preference Settings 4.8 Options for on-screen display To set the options for the on- screen display (OSD), select the Settings > OSD menu. should see a screen like the left figure. To adjust the transparency level of the OSD, set the OSD Trans- parency option as you desire.
4.9 Options for the front display 49 only to its end. 4.9 Options for the front display To set the options for the front display, select the Settings > Front Display menu. You should see a screen like the left figure. The front display shows the currently viewed service’s number and name.
50 Preference Settings 4.11 Options for Photo Album You can change a time interval and effect of slideshow in the photo album. For the photo album feature, see §8.4. To change the time interval of slideshow, select the Settings > Miscellaneous menu, and then set the Slideshow Time Interval option as you desire.
Chapter 5 Every Day Use 5.1 Volume control £ £ ¢ ¡ ¢ ¡ Use the buttons to alter the volume VOLUME VOLUME to a comfortable level. You may need to adjust the volume on your television set too. To temporarily switch off the sound, press the button.
Page 58
52 Every Day Use On the services list, you can see the service information as fol- lows: • Service number and name • Transmitting satellite • Receiving tuner: T1 stands for the first tuner; T2 stands for the second tuner. •...
Page 59
5.2 Watching television 53 you can browse as a group the services that have a same initial. £ Press the ¢ ¡ button at the ser- vices list screen, then you should see a screen like the left figure. In the box on the left side, select a desired initial group by putting the highlight bar on its entry, then all the services hav- ing the selected initial will be displayed in the box on the right £...
54 Every Day Use • To delete the highlighted service, select the Delete op- tion, then you get asked for confirmation. With the choice of Yes, the service will be deleted. If you want to restore it as before, you have to perform service search again.
5.2 Watching television 55 As to how to edit the favourite lists, refer to §6.2. To select a favourite service, put the hightlight bar on a desired £ ¢ ¡ service and press the button, the it will be displayed. To select another group, press the button.
56 Every Day Use In addition, you might see the following symbols: • Subtitle symbol ( ) if subtitle tracks are provided on the current programme. • Teletext symbol ( ) if teletext pages are provided on the current service. •...
5.3 Viewing electronic programme guide 57 tracks, the subtitle symbol ( ) will be marked on the infor- mation box. Pressing the button displays available subtitle tracks. Once you select a subtitle track, it will be displayed. 5.2.6 Viewing teletext On some services, such information as weather reports, news or stock quotations is provided by means of teletext.
58 Every Day Use £ You can travel over previous days with the ¢ ¡ button, and can £ ¢ ¡ travel over next days with the button. To see the programme guide for radio broadcasts, press the button. To switch it back, press the button again.
Page 65
5.5 Using time-shift 59 When you do this, you are no longer watching the live pro- gramme, instead you are watch- ing a delayed presentation. This is called time-shifted television. You can skip commercials until you catch up to the live broad- cast.
60 Every Day Use • To end time-shift, press the button. The live pro- gramme will be displayed. NOTE You can adjust some options for time-shift. Refer to §4.6. 5.6 Viewing in the picture-in-picture screen mode You can watch two services at the same time with one of them presented in a sub-picture.
Page 67
5.6 Viewing in the picture-in-picture screen mode 61 can watch a live programme in the sub-picture. How- ever, you cannot swap the pictures in that case. 6. If both pictures are pay services, only the main-picture will be presented.
62 Organising Services Chapter 6 Organising Services 6.1 Editing the services list You would have got the services list after service search. You can rename, move, lock or delete service entries on the services list. Select the installation > Edit Ser- vices >...
Page 69
6.1 Editing the services list 63 service entries will be listed on the right column. To switch back to the television services list, press it again. To change the name of a service, select the Rename and select a desired service; then the on-screen keyboard appears. See §6.3 as to how to use the on-screen keyboard.
64 Organising Services Fav–NoFav from favourite services to unfavourite services Provider by broadcaster Transponder by transponder 6.2 Editing the favourite lists You can make your own favourite service lists. In fact, you can define multiple favourite service lists, each being a ‘group’ of chosen services.
Page 71
6.2 Editing the favourite lists 65 You can add a favourite service to a group by taking the fol- lowing steps: 1. Put the highlight bar on a desired group entry in the £ ¢ ¡ group list and press the button to select it.
66 Organising Services 6.3 How to use on-screen keyboard You can move the highlight key horizontally with the buttons and vertically with the buttons. Pressing the £ ¢ ¡ button on a key enters its let- ter in the input line. To type a space, select the Space key or alternatively press the button.
Chapter 7 Recording and Playback You can record TV programmes into an external hard drive as well as the built-in hard drive. NOTE To use an external hard drive, you must connect the external hard drive to the USB port or the eSATA port of the digital receiver.
68 Recording and Playback watching another one only if two among the services are pro- vided through the same transponder. The digital receiver has two tuners so that you can enjoy the following: • While playing a recording back, you can watch a service in the sub-picture using the picture-in-picture feature.
7.1 Recording a programme 69 programmes. Topfield is not responsible for damages in- flicted on files that are stored on the hard drive. 7.1.1 Instant recording To instantly record a programme you are watching at present, press the button. Pressing the button will not pause the current recording like it does with a video recorder.
70 Recording and Playback To stop recording, press the button; then a box like the left figure appears, which shows the programmes currently be- ing recorded. Select record- ing by using navigation buttons £ ¢ ¡ then press button to stop the recording.
Page 77
7.1 Recording a programme 71 To add a timer recording, se- lect the Recording > Reserva- tion menu, then the timer list will be displayed. To add a new timer £ event, press the ¢ ¡ button, and a box like the left figure appears. Take the following steps: 1.
Page 78
72 Recording and Playback If your favourite programme is broadcast at weekends and you wish to record every episode of the programme, set the Mode option to Every Weekend. 6. Set the Date option to a desired date, on which the digital receiver will turn on.
7.1 Recording a programme 73 7.1.3 Scheduling recordings using the programme guide If the electronic programme guide is properly provided, you can make timer events on it. The instructions on how to make timer recordings using the electronic programme guide are as follows: £...
74 Recording and Playback 7.1.5 Recording a pay service programme You can record a pay service programme without the subscrip- tion card. However, you need the subscription card to play it back because it has not been descrambled. So it is recom- mended to record pay service programmes with a proper sub- scription card so that they can be descrambled and recorded.
7.2 File archive 75 Recording Select > Recorded Program menu or alternatively press the but- ton to display the recorded programme list. The file in- formation is comprised of the following elements: file num- ber, file name, recording time, running time, file size and so on. You can play, move, delete, rename and lock a recording file.
76 Recording and Playback 3. Set the Lock option to Locked. £ ¢ ¡ 4. Press the button. EXIT 5. The lock symbol ( ) is displayed on it. If you select a locked recording to play it back, you will be asked for your personal identification number.
7.3 Playing back a recording 77 1. Select the Recording > Recorded Program menu or alternatively press the button to display the list of recorded programmes. 2. Put the highlight bar on a desired recording and press £ ¢ ¡ button, then an option box pops up.
78 Recording and Playback • To jump to the end, press the button. • To hide the progress bar, press the button again. 7.3.2 To play in slow motion To watch in slow motion during a playback, press the but- ton.
7.3 Playing back a recording 79 £ ¢ ¡ 2. To add a bookmark, press the button at a desired scene, then you will see a small pointer appear above the progress bar like in the picture above. £ ¢ ¡ 3.
80 Recording and Playback 4. The selected recordings are played in the sequence that they are numbered. 5. To jump to the beginning of the next recording in the queue, press the button to display the progress bar, then press the button.
7.4 Editing a recording 81 7.4 Editing a recording You can cut out or save a part such as commercial from a recording by performing the following steps: 1. Press the button to display the progress bar during a playback. 2.
82 Recording and Playback 7.6 Formatting the hard disk If a new hard drive is installed, it must be formatted because you can neither record nor use time-shift with an unformatted hard disk. You can delete permanently all contents stored in a hard drive by formatting it.
Chapter 8 Entertainment This digital receiver provides several special features for enter- tainment. NOTE To fully enjoy all of the features described in this chapter, you had better configure the network settings properly. As to how to configure the network settings, refer to §9.2. 8.1 Wireless audio If you have a pair of wireless headphones or earphones, you...
84 Entertainment 1. Set the Wireless Audio option to Enable. 2. Turn on your wireless headphones, and put it in pairing mode. 3. Select the Device Scan menu to detect all available wire- less headphones. Once detection is completed, all de- tected wireless headphones get listed.
8.3 Playing back MP3 files 85 2. Press the button and then press the button to select a desired file list except the External list. £ 3. Put the highlight bar on a desired file and press the ¢ ¡ button, then you get asked to select between the built-in and external hard drive.
86 Entertainment 1. Select the Entertainment > MP3 Player or press the button and then the button to display the MP3 file list. 2. Put the highlight bar on a desired file; if you want to play £ ¢ ¡ several files, select them with the button.
8.5 Playing back a video file 87 8.5 Playing back a video file You can play back media files such as photos, videos and music with this digital receiver. Media file formats that you can play back with the digital receiver are as follows: •...
88 Entertainment 8.6 Playing back YouTube contents YouTube is a video sharing website where users can upload, view and share video files. With the SRP-2110, you can access YouTube and play back various contents. When you select the Entertain- ment > YouTube, you should see a screen like the left figure.
8.7 Sharing image files by Yahoo Flickr 89 8.7 Sharing image files by Yahoo Flickr Flickr is an image hosting website and on-line community plat- form. You can search an image file from the network server and view the file using the Flickr. To use this function, select the Entertainment >...
90 Entertainment £ To save an image file to the photo album, press the but- ¢ ¡ Option ton. For the photo album see §8.4. 8.8 SHOUTcast Internet radio SHOUTcast™ Radio is one of the largest directories of profes- sionally and community programmed online radio stations in the world.
8.9 Google weather forecast 91 For more details, visit the SHOUTcast web site, http://www.shoutcast.com. You can check their http://www.shoutcast. terms of service at the com/disclaimer. 8.9 Google weather forecast You can view the weather of your city or other cities. To view the weather, select the Entertainment >...
92 Entertainment 8.10.1 Single mode To play the game in single mode, select the Entertainment > Game > Battle Tank (Single), then take the following steps: 1. Select game mode. 2. Select a character. 3. Buy items as you desire. 4.
Page 99
8.10 Network game 93 Selecting a character After selecting game mode, you should see a screen like the left figure. Select a character referring to Ta- ble 8.1. £ ¢ ¡ If you select the , a character will be chosen randomly. When you play the game for the first time, you can select only two characters.
Page 100
94 Entertainment Buying items After selecting a character, you should see a screen like the left figure. Buy a item referring to Table 8.1. When you finish selecting items, select the READY on the screen as follows: £ ¢ ¡ •...
Page 101
8.10 Network game 95 Playing the Battle Tank When you start the game, you should see a sceen like the fol- lowing figure. Play the game referring to Table 8.2. The character’s weapons. The angle of the character. You can see the direction and speed of wind. You can see the information of the character as follows: ENERGY displays the character’s energy.
4. Selecting a character, map and items for playing. 5. Start playing. NOTE Refer to the Battle Tank user guide as to how to play Battle Tank in network mode. You can download it from the Top- field website, http://www.i-topfield.com.
Chapter 9 Accessing via Network NOTE The following section describes complex functions that should only be used by owners with advanced computer knowledge. This digital receiver provides features of web service and FTP service, by which through the network you can make sched- uled recordings, or transfer recording files to your computer.
98 Accessing via Network NOTE The web server and FTP server of the digital receiver do not work in standby mode. So it must be powered up at all times if you wish to use the web service at any time. 9.1 Configuring the router In this section, the setup program of WRT54G, which is a router manufactured by Linksys, will be referred to as an example of...
9.1 Configuring the router 99 9.1.2 To access over the Internet When you are away from home, you can access the digital re- ceiver inside your home if your router is configured to route access to the digital receiver by means of port forwarding. Via this feature, your router will lead you to the digital receiver when you access your router with its IP address.
100 Accessing via Network which should be supported by your router. 2. Configure your router with the account so that it can communicate with the web site. Whenever a new dynamic IP address is assigned to the router, it will inform the DDNS service provider of the new IP ad- dress.
9.3 Accessing the web server 101 cumbersome thing, you had better assign a static IP address rather than dynamic one. To assign a static IP address, set the Connection Type option to Static, then the IP Address, Subnet Mask, Gateway, Primary DNS and Secondary DNS options become enabled.
Page 108
102 Accessing via Network You cannot only download but also upload recording files or MP3 files in the File Management page. However, if you wish to download or upload a file of which size is 2 gigabyte or more, it is recommended using the FTP server rather than the web server.
9.4 Accessing the FTP server 103 NOTE The maximum number of user connections is one. This means that you cannot access the web server while someone else is occupying it. 9.4 Accessing the FTP server To Access to the FTP server, set the Installation > Network Set- ting >...
Page 110
104 Accessing via Network You can log into the FTP server with the user name and pass- word specified in the Installation > Network Setting > User Info menu. NOTE The maximum number of user connections is one. This means that you cannot access the FTP server while someone...
Page 111
9.4 Accessing the FTP server 105 else is occupying it.
Interface) libraries that available http: from Topfield’s website, //www.i-topfield.com/eng/ download/utility_list.asp. One is Linux version, and the other is Cygwin version. Cygwin is a Unix-like environment and command-line inter- face for Microsoft Windows. Your TAPs will be run with the following conditions: •...
Page 113
• TAPs must be situated in the Program Files folder; if they are placed in any other folder, they will be ignored. As to how to transfer your TAPs to the digital receiver, refer to §8.2 or Chapter 9. To run a TAP in the digital receiver, take the following steps: 1.
Page 114
108 Topfield Application Program toStart folder. If you want to abort the execution of it, press £ ¢ ¡ button at start-up.
firmware and the firmware update tool, which runs on http: most versions of Windows, from the Topfield website, //www.i-topfield.com. 11.1 From a memory stick If you have a USB memory stick, you can update the firmware from it by taking the following steps: 1.
110 Firmware Update 5. Place the highlight bar on the right firmware file and £ ¢ ¡ press the button, and a countdown will be displayed on the front display of the digital receiver. 6. When the message of ‘END’ appears, restart the digital receiver.
Frequency 12603 MHz appointed by the manufac- Symbol Rate 22000 KS/s turer, Topfield, for firmware Polarisation Horizontal update. This transponder information can be changed. You can get the information from the website, http://www.i-topfield.com. Selecting the Start command starts firmware update.
112 Universal Remote Control Appendix A Universal Remote Control The universal remote control allows you to operate the most important functions such as power on/off and volume control on your television, audio-video receiver, or DVD player. For the use of buttons, refer to Table A.1. To be able to control the device, you must adapt the remote control to the device first.
Page 119
1. Turn on the device you want to operate. 2. Point the remote control at the remote sensor on the de- vice. £ ¢ ¡ 3. Hold down the and device button simultaneously for two seconds until the light flashes on. For example, if you want to operate your television with the remote £...
Page 120
114 Universal Remote Control Table A.1: Operating buttons Power on/off Power on/off Power on/off £ ¢ ¡ Volume up Volume up Volume up VOLUME + £ ¢ ¡ Volume down Volume down Volume down VOLUME Mute Mute £ ¢ ¡ Channel up CHANNEL + £...
A.2 Code list for DVD players 129 A.2 Code list for DVD players 3 DLAB KENWOOD 007, 034, 043, 050, 069 AIWA KISS ALBA AMSTRAD A-TREND LAWSON LECSON LENCO BLUE SKY LG (GOLDSTAR) 005, 055, 064, 070 BUSH 078, 079, 082, 085 LIFETEC LOGIX CINE ULTRA...
Page 139
INDEX 133 Index 1st Audio Language, avi, 1st Subtitle Language, 2nd Audio Language, Battle Tank, 2nd Subtitle Language, Battle Tank (Network), 4:3, Battle Tank (Single), 16:9, Blind, 22 kHz, bmp, Brightness in Operation Mode, A/V Output, Access Control, Brightness in Standby Mode, Active, Button, Add to Fav,...
Page 140
134 INDEX eSATA, 14, Common Interface, Component, Every Day, Every Weekday, Conditional Access Module, Connection Type, 24, 100, Every Weekend, Cover, Export System Data, Cut, Cygwin, F10, Factory Setting, Date, Fav–NoFav, 54, Daylight Saving Time, FEC, 29, 30, Default, 54, File Management, Default PIP Size, File Name,...
Page 141
INDEX 135 Home Transponder, Main Display Scrolling, Manual, Import System Data, Media Player, Info Box Display Time, MediaHighway, Info Box Position, MediaHighway EPG, information box, Menu Language, Instant Recording Duration, Microsoft Windows, IP Address, Mini A, IP Setting, Miscellaneous, 49, mkv, Mode, 42, 71, jpg, 86,...
Page 142
136 INDEX Record, normal-screen television, Recorded Program, 70, 75, 77, ON/OFF, recorded programme list, Once, Recording, One Time, Recording Drive, on-screen display, Recover System Data, OPTICAL, Rename, 53, 63, OSD, Reservation, OSD Transparency, Reset Service List, OTA Firmware Upgrade, Other, Overlap, S/PDIF, 19, S/PDIF COAXIAL,...
Page 143
INDEX 137 Slideshow Time Interval, Tuner, Tuner 1, SMATV, 28, Sort, Tuner 1 to Tuner 2, Sorting, 54, Tuner 2, Sound Mode, Tuner 2 to Tuner 1, Standby Mode, 3, Tuner Select, 23, 26, 27, 45, Start, TV, 14, Start firmware upgrade, TV Aspect Ratio, Start Search, Type,...