Function Setting - Mitsubishi Electric PUHZ-RP35VHA Service Manual

11

FUNCTION SETTING

11-1. UNIT FUNCTION SETTING BY THE REMOTE CONTROLLER
Each function can be set according to necessity using the remote controller. The setting of function for each unit can only be
done by the remote controller. Select function available from the table 1.
<Table 1> Function selections
(1) Functions available when setting the unit number to 00 (Select 00 referring to 4 setting the indoor unit number.)
W1 The functions below are available only when the wired remote controller is used.The functions are not available for floor
standing models.
Function
Power failure OFF
automatic recovery ON
Indoor temperature Operating indoor units
detecting (The average is considered as indoor temperature.)
Indoor unit with remote controller
Remote controller's internal sensor
Not supported
LOSSNAY
connectivity Supported (indoor unit not equipped with outdoor air intake)
Supported (indoor unit equipped with outdoor air intake)
Power supply 240V
220V,230V
voltage
Auto operating Auto energy-saving operation ON
mode Auto energy-saving operation OFF
Frost prevention 2: (Normal)
3:
temperature
When the compressor operates, the humidifier also operates.
Humidifier control
When the fan operates, the humidifier also operates.
Change of Standard
For high humidity
defrosting control
(2) Functions available when setting the unit number to 01-03 or AL (07 in case of wireless remote controller)
• When setting functions for an indoor unit in an independent system, set the unit number to 01 referring to 4 setting the
indoor unit number.
• When setting functions for a simultaneous- Twin Triple indoor unit system, set the unit number to 01 to 03 for each indoor
unit in case of selecting different functions for each unit referring to 4 setting the indoor unit number.
• When setting the same functions for an entire simultaneous Twin Triple-indoor unit system, set refrigerant address to AL
(07 in case of wireless remote controller) referring to 4 setting the indoor unit number.
Function
Filter sign 100Hr
2500Hr
No filter sign indicator
Air flow Quiet
( Fan speed )
Standard
High ceiling
No.of air outlets 4 directions
3 directions
2 directions
Not supported
Optional high efficiency
filter Supported
No vanes ( Vane No.3 setting : PLA-AA only )
Vane setting
Vane No.1 setting
Vane No.2 setting
Energy saving air Disabled
flow ( Heating mode )
Enabled
Optional humidifier Not supported
( PLA-AA only )
Supported
No.1 setting ( TH5: 24-28: )
Vane differential setting
No.2 setting ( Standard , TH5:28-32: )
in heating mode
( cold wind prevention ) No.3 setting ( TH5: 32-38: )
Swing Not available
Available
Set temperature in heating Available
mode ( 4 deg up )
Not available
Fan speed when the Extra low
Stop
heating thermostat is OFF
Set fan speed
Disabled ( Standard )
Quiet operation mode
of PLA-AA ( Fan speed ) Enabled ( Quiet operation mode )
Set fan speed
Fan speed when the
cooling thermostat is OFF Stop
Detection of abnormality of Available
the pipe temperature ( P8 )
Not available
Settings
Mode
Settings
No.
07
}
Standard
PLA-AA
High ceiling1
08
High ceiling2
09
10
11
12
13
14
23
24
25
26
27
28
85
Mode No. Setting No.
(when sent from the factory)
1
01
2
1
02
2
3
1
03 2
3
1
04
2
1
05
2
1
15
2
1
16
2
1
17
2
Initial setting ( Factory setting )
Setting 4-Way Ceiling
No.
cassette concealed
PEAD-EA
PLA-AA
PEAD-GA
1
2
3
1 -
2 -
3 -
1 -
2 -
3 -
1
-
2
-
1 -
2 -
3 -
1
-
2
-
1
-
2
-
1 -
2 -
3 -
1
-
2
-
1
2
1
2
3
1
-
2
-
1
2
1
2
Initial setting
Remarks
The setting is
applied to all
the units in the
same
refrigerant
system.
- : Not available
Wall
Ceiling suspended
mounted
PKA-GAL
PCA-GA PCA-HA
PKA-FAL
- -
- -
- -
- - -
- - -
- - -
- -
- -
- -
- -
- -
- -
- -
- - -
- - -
-
-
-
-
-
- - -
- - -
Floor
standing
PSA-GA
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-