Panasonic CS-E9CKP Service Manual page 43

Panasonic ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy
I Setting the Fan Speed
• Press 4 to select:-
There are five stages of fan speed in addition to
Auto Fan speed.
AUTO
FAN – Heating
When the temperature of the discharge
air increases, the fan speed increases.
Cooling G Dry
Changes the fan speed to generate a
cool breeze. The air starts to blow out
approximately 40 seconds after the start
of Cooling or Soft Dry.
I Setting the Vertical Airflow Direction.
• Press 5 to select:-
AUTO
• For COOL/DRY operation.
AUTO
Swing up/down automatically.
AUTO • For HEAT operation
When the discharge air temperature is
low such as at the start of the heating
operation, the air blows at horizontal
level. As the temperature rises, the hot
air blows in a downwards direction.
G Louver adjustment range
•
The adjustment range is different
for each operation i.e. Heating,
Cooling and Soft Dry. (Fig.at left)
•
The angle indicated on the remote
control is different from that on the
About 30°
indoor unit.
About 30° •
The louver angle automatically
changes to prevent condensation
during Cooling and Soft Dry.
• When operation stops, the louver
automatically closes.
About 60°
* Five stages of adjustments can be made in this range.
AUTOHEAT COOL DRY FAN
AUTO
AUTO
FAN
8
OFF/ON
MODE QUIET POWERFUL
7 6
AIR SWING
FAN SPEED
1 2 3
1 3
ON SET
5 4
OFF
CANCEL
2
TIMER
CHECK RESET CLOCK
SETTING THE TIMER
Ensure that the current time is correct before setting the
timer. The timer cannot be set if the time display is
flashing.
I ON-TIMER Operation
To start the air conditioner operation automatically.
• Press 1 to set the operation.
• Press 2 to increase or decrease the time.
• Then press 3.
• To cancel this operation, press 4.
I OFF-TIMER Operation
To stop the air conditioner operation automatically.
• Press 5 to set the operation.
• Press 2 to increase or decrease the time.
• Then press 3.
• To cancel this operation, press 4.
G Timer Mode Operation Details
• When the ON-Timer is set, operation will start
before the actual set time. This is to allow the room
temperature to reach the setting temperature by the
setting time. (Maximum of 35 minutes in advance).
• Once the timer is set, operation will start and stop
at the same time everyday.
• The current time is not displayed when the timers
are set.
• When both timers are used together, the TIMER
mode indicator on the indoor unit remains lit even
when the operation is stopped by the OFF-TIMER.
G Notes
• Do not adjust the vertical airflow direction louver downward
during Cooling and Soft Dry. Drops of water may condense
on the air outlet vent and drip down.
• Use the remote control to change the vertical airflow
direction louver. Using your hands to adjust the direction
may cause the louver to malfunction. If this happens, stop
operation immediately and restart.
I Setting the Horizontal Airflow Direction.
• Press 6 to select:-
Indoor
Horizontal Unit
Airflow
Direction
Remote
AUTO
Control
• For COOL/DRY operation.
AUTO
Louvers swing horizontally at a fixed
speed.
• For HEAT operation
AUTO
When air temperature is low, air is sent
in . When temperature goes up,
louver swing horizontally at a fixed
speed.
G Use this air conditioner under the following
conditions:
Unit in °C
Outdoor
Indoor
DBT: Dry Bulb Temp
WBT: Wet Bulb Temp
DBT WBT DBT WBT
Maximum Temperature-Cooling 32 23 43 26
(Maximum Temperature-Heating) (30) (-) (24) (18)
Minimum Temperature-Cooling 16 11 16 11
(Minimum Temperature-Heating) (2)
(-) (-5) (-6)
CONVENIENCE OPERATION
I Powerful Mode Operation
To obtain the set temperature quickly.
• Used in winter to warm yourself quickly upon
returning home (Heating + Powerful).
• Used in summer to cool yourself after a hot bath
(Cooling + Powerful).
• Press 6.
* Powerful mode indicator (orange) on the indoor
unit will light up.
• To cancel this operation, press once more.
G Note
• The setting temperature and the fan speed changes
automatically in order to heat, cool or dehumidify the
room quickly.
Operation Temperature Fan Speed
HEAT
3.5°C higher
Slightly
2°C lower (For
Automatic COOL
Stronger
first 20 minutes)
1°C lower (For
DRY
first 20 minutes)
www.ilmalämpöpumput.com
43
CS-E9CKP CU-E9CKP5 / CS-E12CKP CU-E12CKP5
G Notes
• If the unit is not going to be used for an extended
period of time, turn off the main power supply. If it is
left at the ON position, approximately 2.8 W of
electricity will be used even if the indoor unit has been
turned off with the remote control.
• If operation is stopped, then restart immediately, the
unit will resume operation only after 3 minutes.
G Operation Details
COOL – Cooling Operation
• To set the room temperature at your preference
cooling comfort.
AUTO – Automatic Operation
• Sense indoor temperature to select the optimum
mode.
• Temperature is not displayed on the remote control
during AUTO operation.
DRY – Soft Dry Operation
• Dehumidifies while maintaining the setting
temperature. The Soft Dry Operation is recommended
during the rainy season.
• If the room temperature exceeds the setting
temperature, operation switches to Cooling.
• The fan speed is rather slow during Soft Dry
Operation.
• The humidity may not decrease when the indoor
temperature is lower than the setting temperature on
the remote control.
HEAT – Heating Operation
• To warm up the room temperature upon your
preference setting temperature.
• Heat is obtained from outdoor air to warm up the
room. When the outdoor ambient air temperature
falls, the heating capacity of the unit might be
reduced. We recommend that you use an additional
heating device when the outdoor ambient air
temperature is low.
FAN – FAN Operation
• Circulates air throughout the room.
• Purifies and deodorizes the air if the air purifying filter
is used. Fan Operation is recommended during
seasons in which neither Heating nor Cooling is used.
I Quiet Mode Operation
To provide quiet operation.
• Press 7.
* Quiet mode indicator on the indoor unit will light
up.
• To cancel this operation, press once more.
G Operation Details
• Air flow sound will reduce during operation.
I Ionizer Mode Operation
Produce negative ion for fresh air.
• Press 8.
* Ion mode indicator on the indoor unit will light up.
• To cancel this operation, press once more.
G Operation Details
• Air conditioner ON:
Provide negative ion during operation.
• Air conditioner OFF:
Provide negative ion with FAN operation.
• If blinking, press 8 twice.
If still blinking, please call service.