Panasonic CS-E9CKP Service Manual page 42

CS-E9CKP CU-E9CKP5 / CS-E12CKP CU-E12CKP5
Panasonic ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy
NAME OF EACH PART
I Remote Control
1
2
3
4
5
6
7
8
9
0
!
G Remote Control Signal.
• Make sure it is not obstructed.
• Maximum distance : 10 m.
• Signal received sound.
One short beep or one long beep.
G Notes for Remote Control.
• Do not throw or drop.
• Do not get it wet.
• Certain type of fluorescent lamps may affect
signal reception. Consult your dealer.
PREPARATION BEFORE OPERATION
I Indoor Unit
6
3
5
1
Connect the power supply cord to an independent
power supply
2
Open the front panel
3
Remove the air filters
AUTO HEAT
4
Fit the air purifying filters in place
5
Insert the air filters
6
Close the front panel
I Remote Control
– To set the current time
AIR SWING
1
ON
OFF
CHECK
1 Press 1.
2 Then press 2 to increase or decrease the time.
3 Press 1 again.
Set time at display will light up.
1 Signal Transmitter
2 Operation Display
3 Ionizer Mode Operation Button
4 Room Temperature Setting Button
(Illuminating button)
AUTOHEA AUT HEAT COOL COOL DR DRY FAN AN
AUT AUTO
5 Operation Mode Selection Button
AUTO AUT
ON
6 Quiet Mode Operation Button
AUTO AUT
OFF
FAN AN
TEMP
7 Vertical Airflow Direction Button
OFF/ON 8 ON-Timer Button
#
9 OFF-Timer Button
$
MODE QUIET POWERFUL
0 Reset Point
AIR SWING $
FAN SPEED
% (Press with fine-tipped object to clear the memory)
1 2 3
^
! Check Point
ON SET
&
To be used by the service technician only.
OFF
CANCEL
*
TIMER
@ OFF/ON Button
(
(Illuminating button)
CHECK RESET CLOCK
)
# Powerful Mode Operation Button
$ Fan Speed Selection Button
% Horizontal Airflow Direction Button
^ Timer Set Button
& Timer Cancellation Button
* Time-Setting Button
( Clock Button
) Remote Control Cover
HOW TO OPERATE
1
2
4
I To start the operation
• Press 1.
• POWER indicator (green) on the indoor unit will light up.
(LED blinks when the room temperature is low at the
start of heating or operation mode is selected during
Automatic Operation.)
COOL DRY FAN
The power monitor lamps light up to show the
AUTO
compressor operating condition.
• To stop, press once more.
AUTO
I Setting Mode
FAN
• Press 2 to select:-
FAN SPEED
2 3
SET
CANCEL
2
TIMER
1
RESET CLOCK
2
3
5
1
6
4
AUTO – Automatic Operation
HEAT – Heating Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
FAN – Fan Operation
www.ilmalämpöpumput.com
42
G How to Insert the Batteries
2
1
1
Slide down the remote control cover completely
2
Insert the batteries
– Be sure the direction is correct
– 12.00 at display - flashing
• Set the current time (CLOCK) immediately to
prevent battery exhaustion.
G About the batteries
• Can be used for approximately one year.
G Observe the following when replacing the
batteries
• Replace with new batteries of the same type.
• Do not use rechargeable batteries (Ni-Cd).
• Remove the batteries if the unit is not going to be
used for a long period.
I Setting Temperature
• Press 3 to increase or decrease the temperature.
• The temperature can be set between 16°C ~ 30°C.
(Not adjustable during Fan Operation.)
• Recommended temperature:
HEAT : 20°C ~ 24°C
COOL : 26°C ~ 28°C
DRY : Approx. room temperature
I Automatic Operation
• At the start of the Automatic operation, Heating,
Cooling or Soft Dry is automatically selected according
to the outdoor temperature, indoor temperature and
setting temperature.
• The operation mode changes every half hour, when
necessary.
(Ex) Setting Temperature at 25°C
36°C
S
C
32°C
O
O
F
O
31°C
T
H
L
E
I
D
A
N
R
T
G
Y
I
18°C
N
G
16°C
13°C 19°C 21°C 23°C 25°C
Outdoor Temperature