Advertisement
SpA
IDENTIFICATION AND TECHNICAL SPECIFICATIONS
Model: BL10T
Weight of BL 10T
(with cutter): 24 Kg
Engine: 4 stroke
Manufacturer: TECUMSEH
Model: VANTAGE 35
Cubic capacity: 148 cc
Power: 2.4 Kw
RPM: 3150
Consumption Kg/h: 0.8
Fuel: Unleaded petrol
Dry air filter
•
All engines installed on this motorised hoe have a starting system with self-winding cord, as well as exhaust pipe
protection.
•
Engines installed on the BL 10 are lubricated with SAE 30 oil. Quantity of oil in engine: 0.6 lt.
•
The transmission unit is lubricated with SAE 80W/90 oil - quantity 1 hg.
GENERAL SPECIFICATIONS OF THE MOTORISED HOE:
1.
Vee-belt and worm screw transmission; one forward gear.
2.
Forward engage/disengage lever fitted on handle.
3.
Engine stop device fitted on handle.
4.
Handle can be dismantled to facilitate transport.
5.
Height adjustable spur.
6.
Standard supply cutter of 40 cm; cutter diameter 26 cm; Max cutter revs of 170
rpm for BL10, BL10H and BL10T; Max cutter revs of 260 rpm for BL10HX, with
22 cm diameter and maximum width of 30 cm.
7.
Front transfer wheel (Fig.N°7).
To identify the machine (serial number, engine, weight, and power), read the
data-plate located as shown in the photo. See Ref. "A" of Fig. N°3.
PACKING AND TRANSPORT
WIDTH: 60 cm
o
DEPTH: 40 cm
o
HEIGHT: 55cm
o
•
Remove the motorised hoe from its packing
•
Fit the spur Ref. "A" (Fig. N°4) with the snap-fit pin in the
packing as shown in figure N°5. The standard cutters - see
Fig. N°6 – are to be fitted on the tiller shaft by means of both
snap-fit pins that are in the packing.
•
When fitting the cutter knives, take care over the direction of
the cutting edge and the timing of the knives as shown in
figure 6.
•
Install the handlebar support tube Ref. "F" (Fig. N°4) , fitting
it in its seat on the rear of the motorised hoe, and secure it
with the screws and nuts Ref. "B" (Fig. N°4)
•
Next, fit the handles Ref. "C", locking them with the screws
and knobs Ref. "D".
•
To facilitate transport and reduce dimensions, the handles
can be dismantled, using the handlebar support Ref. "F"
(Fig. N°4) as transport handle (see Fig. N°8).
Model: BL10B
Weight of BL 10B
(with 40 cm cutter): 24 Kg
Engine: 4 stroke
Manufacturer: BRIGGS &
STRATTON Model: SPRINT
Cubic capacity: 148 cc
Power: 2.5 Kw
RPM: 3600
Cons umption Kg/h: 0.8
Fuel: Unleaded petrol
Dry air filter
Model: BL10 HS
Weight of BL 10HS
(with cutter): 25 Kg
Engine: 4 stroke
Manufacturer: HONDA
Model: GCV 135
Cubic capacity: 135 cc
Power: 3.4 Kw
RPM: 3600
Consumption Kg/h: 1.06
Fuel: Unleaded petrol
Dry air filter
BL 10
Model: BL10 HX
Weight of BL 10HX
(with cutter): 18 Kg
Engine: 4 stroke OHV
Manufacturer: HONDA
Model: GXV 50
Cubic capacity: 49 cc
Power: 1.6 Kw
RPM: 5000
Consumption Kg/h: 0.6
Fuel: Unleaded petrol
Dry air filter
Fig. n°3
Fig. n°4
3
Advertisement
