Operating Procedure; Setting The Speakers - JVC RX-D411S Instructions Manual

Operating procedure

1, 7
On the front panel ONLY:
Before you start, remember...
There is a time limit in doing the following steps. If the setting
is canceled before you finish, start from step
Ex.: When setting the DIGITAL IN 1 terminal
1
Press SETTING.
MULTI JOG now works for the setting operation.
2
Turn MULTI JOG until the item you want
to set appears on the display.
• As you turn MULTI JOG, the setting items change as
follows:
SUBWOOFER Ô FRONT SPK Ô CENTER SPK Ô
SURROUND SPK Ô S BACK SPK Ô S BACK OUT Ô
DIST UNIT Ô FRONT L DIST Ô FRONT R DIST Ô
CENTER DIST Ô SURR L DIST Ô SURR R DIST Ô
S BACK DIST Ô S BACK L DIST Ô S BACK R DIST Ô
EX/ES/PLIIx Ô DUAL MONO Ô SUBWOOFER OUT
Ô CROSSOVER Ô LFE ATT Ô MIDNIGHT MODE Ô
DIGITAL IN 1 Ô DIGITAL IN 2 Ô DIGITAL IN 3 Ô
AUDIO DELAY Ô HDMI SELECT Ô CMPNT SELECT
Ô VIDEO OUTPUT Ô AUTO MODE Ô (Back to the
beginning)
3
Press SET.
The current setting of the selected item appears.
4
Turn MULTI JOG to select the appropriate
setting.
DVR/DVD Ô VIDEO Ô VCR Ô TV
5
Press SET.
Your setting is stored.
6
Repeat steps 2 to
necessary.
7
Press SETTING.
The source indication resumes on the display.
30
3, 5 2, 4
1
again.
5 to set other items if

Setting the speakers

To obtain the best possible surround effect from the Surround
and DSP modes, register the setting about the speaker after all
connections are completed.
• If you have performed Precise Surround Setup on pages 16
to 18, the following settings are not required.
• You cannot adjust these items directly from the remote
control.
7 Setting subwoofer information—
SUBWOOFER
Select if you have connected a subwoofer or not.
SUBWFR YES Select when you have connected a
subwoofer.
The subwoofer indicator (
the display. You can adjust the subwoofer
output level (see page 36).
SUBWFR NO Select when you have not connected a
subwoofer. Selecting this changes the front
speaker size to "LRG" (see below).
Initial setting: NO
7 Setting the speaker size—FRONT SPK (front
speakers), CENTER SPK (center speaker),
SURROUND SPK (surround speakers), S BACK
SPK (surround back speakers)
Register the sizes of all the connected speakers.
LRG (large) Select when the cone speaker size is larger
than 12 cm.
SML (small) Select when the cone speaker size is smaller
than 12 cm.
NO Select when you have not connected
the speaker. (Not selectable for the front
speakers.)
Initial setting: LRG (for the front speakers)
SML (for the other speakers)
NOTES
• If you have selected "SML (small)" for the front speaker size, you
cannot select "LRG (large)" for other speakers.
• When "SUBWOOFER" is set to "NO," the front speaker size is fixed to
"LRG (large)" (and you cannot select "SML (small)").
• When "SURROUND SPK" is set to "SML (small)," you cannot select
"LRG (large)" for the surround back speaker.
• When "SURROUND SPK" is set to "NO," the surround back speaker is
fixed to "NO."
7 Setting the surround back speaker(s)—
S BACK OUT
Register the number of the surround back speaker(s).
SB OUT 1SPK Select when you use a single surround back
speaker.
SB OUT 2SPK Select when you use 2 surround back
speakers.
Initial setting: 2SPK
NOTES
• When "S BACK SPK" is set to "NO," you cannot select "S BACK OUT."
• When "S BACK OUT" is set to "1SPK," connect the surround back
speaker to the left surround back speaker terminal (see page 8). No
sound comes from the surround back speaker if you connect it to
the right surround back speaker terminal.
) lights up on