Related Manuals for NeoPro Imperial
Summary of Contents for NeoPro Imperial
- Page 1 Integrator’s Guide Imperial ™ 12x8 HD Component Video Matrix Switch with Pass-Through Outputs...
-
Page 2: Table Of Contents
Controlling from an IR remote control ........8 Last Command Feedback................10 Setup Menu....................... 10 Care and Maintenance..................12 Specifications ....................13 Performance ................13 Power ..................13 Physical ..................13 2 Year Warranty ....................15 Imperial Matrix Switch User’s Guide (DOC42-00010-A_NeoPro-Imperial.doc) -
Page 3: Introduction
The Imperial is a 12x8 high definition component video matrix switch, with pass-through outputs for stacking multiple units. The Imperial can be stacked up to 12 units to build a 12x96 matrix system. Both products are very similar in function, so this single user manual will guide you through both products. -
Page 4: Installation
Remove this film before using your matrix switch. Inputs The Imperial has 12sets of YPbPr component video inputs. Connecting source devices to the matrix switch can be done in any order. All inputs have the same performance, so organize them as you see fit. -
Page 5: Outputs
The maximum length of cable to each zone will vary on the quality of the cable used, but if high quality cable is used, the Imperial can support displays 300 feet away. RS-232 Serial The serial port on the rear panel is labeled “RS-232”. It is wired as a “DCE”... -
Page 6: Rear Panel Ir
The chassis is a 2 rack units high only when the bottom feet are removed. Removal requires a Philips screwdriver. Be careful when turning over the unit as to not scratch the top paint Imperial Matrix Switch User’s Guide (DOC42-00010-A_NeoPro-Imperial.doc) - Page 7 Imperial Matrix Switch User’s Guide (DOC42-00010-A_NeoPro-Imperial.doc)
-
Page 8: Operation
Operation Overview The Imperial is designed to be controlled from a third party control system, either via RS232 or IR. The buttons on the front panel allow the control of power and status feedback, however matrix control must be performed from external sources. - Page 9 Select, # Sends input # to all outputs Figure 1 - IR Remote numeric button locations Imperial Matrix Switch User’s Guide (DOC42-00010-A_NeoPro-Imperial.doc)
-
Page 10: Last Command Feedback
Use the “Select” button to change any of the optional settings. The menus are as follows: Setup:Panel LEDs This option will turn off all the front panel LED lights. The matrix’s behavior is otherwise unchanged. The default in ON Imperial Matrix Switch User’s Guide (DOC42-00010-A_NeoPro-Imperial.doc) - Page 11 Any of the above selections will be applied instantly. There is no need to save the changes. At any time the user may press exit to return to the home screen, or wait 10 seconds and the home screen will return on it’s own. Imperial Matrix Switch User’s Guide (DOC42-00010-A_NeoPro-Imperial.doc)
-
Page 12: Care And Maintenance
Care and Maintenance The Imperial matrix switch does not require any regular maintenance besides keeping it clean. Never use harsh cleaners or solvents on the front panel. There are several dusting products for electronics, and standard glass cleaner may be used. -
Page 13: Specifications
Input voltage 90-240V AC 50-60Hz autosensing Input power Physical Dimensions 17”W x 3.5”H x 10.75”D Dim. with feet (removable) 17”W x 3.75”H x 10.75”D Unit Weight 8.8 lbs (typical) Shipping weight 13 lbs (typical) Imperial Matrix Switch User’s Guide (DOC42-00010-A_NeoPro-Imperial.doc) - Page 14 Imperial Matrix Switch User’s Guide (DOC42-00010-A_NeoPro-Imperial.doc)
-
Page 15: Year Warranty
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state and country to country. Imperial Matrix Switch User’s Guide (DOC42-00010-A_NeoPro-Imperial.doc) - Page 16 © 2007 NeoPro www.neoprointegrator.com Imperial Matrix Switch User’s Guide (DOC42-00010-A_NeoPro-Imperial.doc)