Programming The Playing Order Of The Tracks - Program Play - JVC MX-J333VU Instructions Manual

To locate a particular point in a track
During play, press and hold 1 x or ¡ x.
• 1: Fast reverses the disc.
• ¡: Fast forwards the disc.
When using the remote control, press and hold
1 / 4 9 or ¢ / ¡ *.
To go to another track
Press 4 ; or ¢ ; repeatedly before or during
playback.
• 4: Goes back to the beginning of the current
or previous tracks.
• ¢: Skips to the beginning of the next or
succeeding tracks.
When using the remote control, press 1 / 4 9
or ¢ / ¡ * during or before playing.
If you press and hold 4
4 4 4 4 4 or ¢ ¢ ¢ ¢ / ¡ ¢
9
You can change the tracks continuously.
To go to another track directly using the number buttons
Pressing the number button(s) ^ before or during play allows you
to start playing the track number you want.
Ex.: For track number 5, press 5.
For track number 15, press +10,
then 5.
For track number 20, press +10,
then 10.
For track number 32, press +10,
+10, +10 then 2.
Programming the Playing Order of the Tracks —
Program Play
You can arrange the order in which the tracks play before you start
playing. You can program up to 32 tracks.
• To use Repeat play (see page 11) for Program play, press REPEAT
n after starting Program play.
1
Place discs.
• If the current playing source is not the CD player, press CD
6 y, ), then 7
2
Press PROGRAM v button.
A.BASS EX S.MODE
A
• If a program has been stored in memory, the program is called
up.
EN6-16;MX-J333V/PM6
TUNING
PRESET
PREV NEXT
4 4 ¢ ¢ 1 1
4 / ¢ 4 ¢ ¢ (or 1 1 1 /
;
¡ ¡ ¡ ¡
* before playing)
z, _ before going to the next step.
PROGRAM
1 2 3
PRGM
10
3
Press one of the disc number buttons
(CD 1, CD 2 and CD 3) r, 1 to
select the disc number you want to
play.
Track number
A.BASS EX S.MODE
PRGM
A
Program step number
Disc number
4
Select a track from the CD selected in the above
step.
On the unit: On the unit:
Press 4 ; or ¢ ; to select the track number, then press
SET k.
PRESET
PREV NEXT
On the remote control: On the remote control:
Press the number buttons ^.
• For how to use the number buttons,
see "To go to another track directly
using the number buttons" described
to the left.
A.BASS EX S.MODE
PRGM
A
5
Program other tracks you want.
• To program tracks from the same disc, repeat step 4.
• To program tracks from a different disc, repeat steps 3 and 4.
6
Press CD 6 y, ).
The tracks are played in the order you have programmed.
To stop during play, press 7
To exit from Program play mode, press PROGRAM v again
before or after play so that the unit enters Continuous play mode.
(The program you have made is stored in memory until you erase
the program or turn off the unit.)
If you select TAPE or AUX or FM/AM after you set programming or
Program play and also program recording, you see sometimes the
current CD's track number and total time on display.
In this case, press program button until disappear PRGM on display
at CD function.
10
6/30/99, 2:26 PM
3
CD
2
CD
1
CD
1 2 3
SET
1 2 3
z, _.
Continued