Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
The LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption. (14) The LCD module is designed so that the CFL in it is supplied by Limited Current ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 5
Taking out the monitor by grasping the LCD panel. That may cause “Mura” Place the monitor on a clean and soft foam pad. Placing the monitor on foreign objects. That could scratch the surface of the panel or cause “Mura” ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
One ViewSonic Printed Quick Setup Guide A3 sized with Graphical instruction type; localized per SKU. i.) One ViewSonic User’s Guide in a 3.5” CD. Since N2635w-M is intended to be a NA product for ViewSonic, table below further illustrate Region / SKU Product Name...
Page 7
V260B1-L01. The following table defines this panel specification. Any changes in panel must be pre-approved by ViewSonic in written. Parameter Specification a-Si TFT Active Matrix Wide Color, Transmissive Mode, Normally LCD Type Black LCD Interface 1-Channel LVDS Resolution (Native) 1366 x 768 WXGA Display Area 26”...
Page 8
<2% <2% (Po=0.1 to 1 W, f=1KHz) Signal to Noise: 30 dB (40Hz to 15KHz) 40 dB (400Hz to 20 kHz) Electrical The following table defines the electrical specification of this product. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 9
The product firmware of VS11769-1M shall have a firmware version of V:P01 or later version. Any changes/revisions afterward shall also be pre-approved by ViewSonic in written. For VS11769-1M, its firmware shall have a built-in frequency table for NTSC/ATSC off-air TV/CATV, Closed-Caption, and with MTS implementation.
Page 10
IR; Made by Bontech Electronics Co., Ltd. Off axis ± 15° ≥ 5M Range On axis: ≥ 7M 100,000 cycle operations at a rate of 20~30 cycle / minute without load Life Testing (Buttons) (with battery) ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 11
Molded Plastic Parts Specification, VSCMPPSPEC001V1.2. Screen Printed Parts, Bird Logo Recess Artwork shall be provided and confirmed by ViewSonic. Rear Label A label identifying the product name, model/serial number and FCC ID/Logo shall be placed into the rear label recess located on the rear panel of the chassis.
VOL+ and MENU buttons again to unlock it. 2. Press VOL- and VOL+ buttons at the same time to lock OSD menu, and press VOL- and VOL+ buttons again to unlock it. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Headphone Jack Connect this port to your headphone. HDMI Input Terminal Connect this port to the HDMI output of A/V device. Power (AC input) Using power cord provided, connect to a power source. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Remote Control ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 15
TV/CATV Swap between TV/CATV PICTURE Select picture modes RETURN Return to previous channel CH▲ and CH▼ Adjust Channel UP/DOWN FAV.CH Select from preset Favorite Channels MENU On Screen Display (OSD) menu ON/OFF ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Color: To adjust color. (right: brilliant color, left: pale color.) • Tint: To adjust tint level. (right: greenish tone, left: reddish tone.) • Sharpness: To adjust picture sharpness. (right: sharper, left: softer.) ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 17
Phase: To adjust delay time of phase in order to reduce the noise of picture. Clock: To adjust delay time of clock in order to reduce the noise of picture. Audio Menu — To set the audio quality and status In TV source: ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 18
It is only active in TV source. • Tuner Mode: To select Cable or Air as the TV source. Select “Cable” if you want to watch Cable TV channels, and select Air to watch Air TV channels. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 19
Setup Menu — To set up OSD window In TV, AV, S-Video, YPbPr, HDMI source: Note: When in AV, S-Video, YPbPr or HDMI source,the TV option on the left does not appear. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 20
Timer: To set power-on and power-off time. Sleep Timer: To set the off timer from 10~120 minutes. Auto Sleep: To set the off timer for longer intervals -- 1 hour, 2 hours, or 5 hours. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 21
Background Color: To select background color. Background Opacity: To select background opacity. Window Color: To select window color. Window Opacity: To select window opacity. • Memory Recall: To restore the factory default settings. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 22
Enter password and the screen below will show. (The default password is 0000.) • Channel Block: To block channels. Use ▲▼ to select the channel you want to block, and then press ENTER to block or unblock it. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 23
Use ENTER button to block or unblock the ratings, and use MENU to exit. U.S. Movie Ratings: To adjust movie blocking level in the US. You can select between G, PG, PG-13, R, NC-17, or X. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 24
13 ans + Not appropriate for children of less than 13 years Use ENTER button to block or unblock the ratings, and use MENU to exit. Block Unrated: To block unrated movie or TV programs. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 25
• Clear All: To clear all the locks set before, press ENTER, and then select “OK” to confirm. Notes:Initial password:0000 If you forget your initial password,you can press"3660"to resume. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
MT5371 supports alpha blending for Video and two OSD planes. It also supports 10bit gamma correction and advanced dithering processing for LCD display with 6/8/10 bit output. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 27
MT5371 is also including a fully HDMI-compliant receiver that fits directly into home theater products such as LCD TVs, plasma TVs and HDTVs. The receiver is capable of supporting ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 28
IC YDA138. Two DAC outputs from MT8291 reach 2Vrms in a 12V supply environment including a headphone, two left/right line outputs with volume gain/attenuation from -127 dB to +12 dB and digital ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 29
The IC YDA138 is a class-D amplifier that can be output power of 10Watts per channel on a 6-ohm load speaker when using a 12V power supply operation. MT5112 ATSC+NTSC Combo Tuner MT5371 CVBS YDA138 AV/SV Audio(RCAR/L) MT8291 Speaker (Audio Amp.) (Audio Codec) YPbPr Audio(RCAR/L) PC/DVI Audio(mini jack) HeadPhone ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
ENTER, The color warm will auto adjust. The act of EHITE BALANCEL is completed when EHITE BALANCEL disappeared. 4.After adjusting, switch to FULL WHITE and check the value of each color. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 31
After final QC step, we must to erase all saved changes again and restore the factory defaults. You should do “All Mode Reset” again. Turn off the LCD TV by pressing “Power” button. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 34
B.CHANNEL36: Check whether the color of the color bar is normal. C.CHANNEL69: Turn RF attenuator and check the critical point of the change of the image’s S/N is under LEVEL<45~85> dBu, regards as normally. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 35
13.328ms 16.667ms 16.666ms V TOTAL 15.880ms 12.795ms 16.000ms 15.880ms V DISPLAY 0.600ms 0.466ms 0.444ms 0.600ms V B-Porch 0.124ms 0.050ms 0.111ms 0.124ms Vs Width 0.000ms 0.000ms 0.000ms 0.000ms V Border H/V Sync Interlace ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 36
H B-Porch 1.310us 1.037us H Width 0.000us 0.000us H Border 16.662ms 16.661ms V TOTAL 16.097ms 16.005ms V DISPLAY 0.377ms 0.594ms V B-Porch 0.126ms 0.047ms Vs Width 0.00ms 0.00ms V Border H/V Sync Interlace ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 37
DDC Card RS-232 cable Barcode Reader VGA Cable N2635WM LCD TV DDC Card RS-232 Cable VGA Cable Barcode Reader 2.2 Setup Procedure 2.2.1 Connect VGA Card and DDC Card with RS-232 cable. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 38
2.2.4 Connect Power Cord to N2635WM LCD TV. 2.2.5 Press ‘MENU’and ‘ENTER’ at the same time, then go into the BURN IN MODE. 2.3 DDC Key In Procedure 2.3.1 run DDC exe 2.3.2 Choose model number the ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 39
2.3.3 Press “ENTER” key. 2.3.4 Press “F4” key ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 40
2.3.5 Input bar code 2.3.56Press “ENTER” key, then the successful picture is as follows. “DDC DOWNLOED OK! 2.3.6 Exit program. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 41
3.1 Equipment Needed N2635WM LCD TV RS-232 cable Barcode Reader HDMI Cable N2635WM LCD TV RS-232 Cable HDMI Cable Barcode Reader 3.2 Setup Procedure 3.2.1 Connect HDMI Card and DDC Card with RS-232 cable. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 42
3.2.3 Connect DDC Card and N2635WM LCD TV with HDMI Cable. 3.2.4 Connect Power Cord to N2635WM LCD TV. 3.3 DDC Key In Procedure 3.3.1 Run DDC.exe 3.3.2 Choose model number then ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 43
3.3.3 Press “ENTER” key. 3.3.4 Press “F4” key. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 44
3.3.5 Input bar code 3.3.6 Press “ENTER” key, then the successful picture is as follows. “DDC DOWNLOED 3.3.7 Exit program ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 45
USB Device detected and follow Windows comments to finish the Driver install. 4.4 Execute the Mtktool to start download the file. The Mtktool program will be upgraded if necessary. "MtkTool Auto BaudRate.exe" 4.5 The Mtktool Operat 4.5.1 Select Platform : MT537X ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 46
4.5.2 Select COM port. Depends on the COM port assigned in System Device Manager (Refer below right). 4.5.3 Select Baud Rate. 115200x 8 (Suggestion) ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 47
4.5.4 Enable the USB Bridge. 4.5.5 Browsing the File to download. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 48
2. You can slow down the baud rate if some Flash memory can not works properly in high-speed download. 3. Please call the Media Tek contact window if any problem found like unsupported Flash Type or fail to download. ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
1.4 Place the LCD TV into the carton. At last, close the carton and seal it with tape. (Figure 4) 1.Power Cord 2. User’s Guide 3.Remote contrl 4.Guarant Card 5.Battery Figure 3 Figure 4 ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 51
2.1 Unscrew 6 screws in the Rear Cover. 2.2 Prize the rectangle hole on Rear Cover (Fig.1) with a screwdriver(Fig.2) to make the Rear Cover detach from the LCD TV. Fig.1 Fig.2 ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 52
Rear Cover ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 53
Disassembly of Main Board,Power Board,Front Cover and Panel Unit. 3.1. Unscrew 2 screws to remove Bracket fix. Bracket fix 3.2. Unscrew 2 screws to move Bracket Fix . Bracket Fix ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 54
3.3. Unscrew screws 4 to move Power Board and to move Switch PCB . Power Board Switch PCB 3.4. Unscrew screws 10 to move Front Cover . Front Cover ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 55
3.5. Unscrew screws 10 to move Shield Plate . Shield Plate 3.6. Unscrew 3 screws to remove dust cover. Dust Cover ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 56
3.7. Unscrew 11 screws to remove METAL FITTG-I/O-Down and METAL FITTG-I/O-Side. METAL FITTG-I/O-Down METAL FITTG-I/O-Side 3.8. Unscrew 4 screws and disconnect the wires to remove Main Board. Main Board ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 57
3.9. Unscrew 4 screws and disconnect the wires to remove Power Board. Power Board 3.10. Unscrew screws 4 to move Panel Bracket . Panel Bracket ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 58
3.11 Unscrew screws 4 to move Bracket Fix and to move Panel Unit . Bracket Fix Panel Unit ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Replace Power Check P101 5V,12V power module is module Check 3.3V is on Replace I103 C115? Check IR Board Replace IR Board Check X102 is OK? Replace X102 Replace I116 & I118 ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 60
6.2. NO VOICE AV,S-VIDEO,YPbPr Check Wire Check I114 Pin24 Connection on has output signal? power module is Replace I124 Replace I114 Check I116 I2S signal output to Replace I116 I124? Check Speaker Wire ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Page 61
6.3. NO DISPLAY YPbPr S-VIDEO NTSC TV Check Video wave Check Replace Check Replace I114 Replace form is on I114 Pin25? L138,R223,R222,C393, L142,R238,R239,C405 L138,R223,R222,C393, L142,R238,R239,C405 R224,C394 is OK? R224,C394 is OK? Replace Check C178,R140, C178,R140,C177 C177 is OK? Check I116 has output signal at Replace I116 Pin9,10,13,14,17,18,2...
Page 62
Replace I116 21,22,25,26 of P113? Check the LVDS Replace LVDS wire from P113 to Wire panel is OK? Check inverter wire Replace Inverter from power module Wire to panel is OK? Replace Panel ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
R0603 D103 R135 B340 R136 R0603 182/ 1% R0603 1.25 x (1+182/110) = 3.319V 0.8 x (1+1K/1K) = 1.6V C173 0.1uF POWER SUPPLY +3V3 FOR MT5112 POWER SUPPLY +1V8 FOR MT5112 C0603 ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Page 89
BOM LIST ( N2635w-1 ) ViewSonic Model Number: VS11769-1M Rev: 1a Serial No. Prefix: QNE Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty E-00008342 2346110496P CS 0603/X7R/50V 0.1u K T CAP CHIP C103 2346110496P CS 0603/X7R/50V 0.1u K T...
Page 90
Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty 2341110296P CS 0603/COG/50V 1000p J T CAP CHIP TEMPERATURE 125'C C393 2346110396P CS 0603/X7R/50V 0.01u K T CAP CHIP C394 E-C-0404-4424 2341115096P CS 0603/COG/50V 15p J T CAP CHIP TEMPERATURE 125'C...
Page 95
Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty 2336322713P EC 220u/ 16V 8*7 P=5.0 T CAP MINI ELE 105'C C480 2336047713P EC 470u/ 16V 8*12 P=5.0 T HI-LIFE LOW ESR E.CAP(4000hr) C494 2336322713P EC 220u/ 16V 8*7 P=5.0 T...
Page 96
Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty 2346110496P CS 0603/X7R/50V 0.1u K T CAP CHIP C257 E-00008342 2346110496P CS 0603/X7R/50V 0.1u K T CAP CHIP C258 E-00008342 2346110496P CS 0603/X7R/50V 0.1u K T CAP CHIP C259 E-00008342...
Page 97
Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty 2346110496P CS 0603/X7R/50V 0.1u K T CAP CHIP C461 E-00008342 2346110496P CS 0603/X7R/50V 0.1u K T CAP CHIP C462 E-00008342 2346110496P CS 0603/X7R/50V 0.1u K T CAP CHIP C464 E-00008342...
Page 102
Company: Add: Tel: Fax: E-mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com) ViewSonic Corporation N2635w-1M Confidential - Do Not Copy...