Download  Print this page

Sony Trinitron CPD-E210 Service Manual

Trinitron color monitor.
Hide thumbs

Advertisement

http://cxema.ru

Advertisement

   Related Manuals for Sony Trinitron CPD-E210

   Summary of Contents for Sony Trinitron CPD-E210

  • Page 1 http://cxema.ru...
  • Page 2: Power Management

    CPD-E210 POWER MANAGEMENT The power saving mode complies with the VESA Display Power Management Signaling standard. Each state of power management shall be activated by the host computer terminating the appropriate sync signals. Blanking the video must precede termination of the sync signals. The elapsed time counter shall also be controlled by the host computer.
  • Page 3: Table Of Contents

    CPD-E210 TABLE OF CONTENTS Section Title Page Safety Check-Out Instructions ............... 4 1. GENERAL .................. 5 2. DISASSEMBLY 2-1. Cabinet Removal ............12 2-2. Service Position ............12 2-3. A, D & H Board Removal ..........12 2-4. Picture Tube Removal ..........13 3.
  • Page 4: Safety Check-out Instructions

    CRITIQUE POUR SECURITE FONCTIONNEMENT. NE LES REMPLACER QUE PAR DES COMPOSANTS SONY DONT LE NUMERO DE PIECE EST INDIQUE DANS LE PRESENT MANUEL OU DANS DES SUPPLEMENTS PUBLIES PAR SONY. LES REGLAGES DE CIRCUIT DONT L'IMPORTANCE EST CRITIQUE POUR LA SECURITE DU FONCTIONNEMENT SONT IDENTIFIES DANS LE PRESENT MANUEL.
  • Page 5 CPD-E210 — 5 — http://cxema.ru...
  • Page 6 CPD-E210 — 6 — http://cxema.ru...
  • Page 7 CPD-E210 — 7 — http://cxema.ru...
  • Page 8 CPD-E210 — 8 — http://cxema.ru...
  • Page 9 CPD-E210 — 9 — http://cxema.ru...
  • Page 10 CPD-E210 — 10 — http://cxema.ru...
  • Page 11 CPD-E210 — 11 — http://cxema.ru...
  • Page 12: Disassembly

    CPD-E210 SECTION 2 DISASSEMBLY 2-1. CABINET REMOVAL 2-2. SERVICE POSITION 1 When the D board is placed in service position, the Safety Earth Wire (green and yellow wire) is disconnected. 2 After service is completed and the 2-3. A, D & H BOARD REMOVAL...
  • Page 13: Picture Tube Removal

    CPD-E210 2-4. PICTURE TUBE REMOVAL ANODE CAP REMOVAL WARNING: High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. Short between anode and CRT coated earth ground strap.
  • Page 14: Safety Related Adjustments

    CPD-E210 SECTION 3 SAFETY RELATED ADJUSTMENTS When replacing parts shown in the table below, the 8) After adjusting the High Voltage within specification, following operational checks must be performed as a put the RV cover on RV501 as shown in Figure 1 and apply safety precaution against X-ray emissions from the unit.
  • Page 15: Adjustments

    CPD-E210 SECTION 4 ADJUSTMENTS Connect the communication cable of the connector located on the D board on the monitor. Run the service software and then follow the instructions. Allow a 30 minute warm-up period prior to making the following adjustments: 12.
  • Page 16 CPD-E210 2. Display crosshatch pattern with red and blue lines and 12. Adjust V.TILT with TLV VR. black field. TLV Movement 3. Adjust H.STAT and V.STAT with 4 pole magnet. Use 4 pole magnet, not "HSTAT" and "VSTAT". 4-Pole Magnet 13.
  • Page 17 CPD-E210 B. Vertical Convergence 4-7. DIGITAL CONVERGENCE ADJUSTMENT Convergence (Low) Mode 1. Adjust the H.STAT and V.STAT with "HSTAT" and "VSTAT". A. Horizontal Convergence Adjust each misconvergence point in sequence. 2. Repeat the procedure of A and B so that the convergence of the entire screen is within the specification.
  • Page 18 CPD-E200 NOTES: — 18 — http://cxema.ru...
  • Page 19 http://cxema.ru...
  • Page 20 http://cxema.ru...
  • Page 21 http://cxema.ru...
  • Page 22 http://cxema.ru...
  • Page 23: Semiconductors

    CPD-E210 5-4. SEMICONDUCTORS 2SK3332 DTC143ESA 2SC4634LS-CB11 2SC3209LK-TP 2SJ449(1) 2SC2412K-T-146-QR DTC114EKA-T146 2SK2098-01MR-F119 2SA1037AK-T146-R 2SC3311A-QRSTA 2SK2843LBSSONY 2SC3941A-Q(TA) 2SA1309A-QRSTA IRFU110 DTA114EKA-T146 1SR139-400T31 D4SB60L D3S4M RGP10DG23 HZ55.6NB2TD HZS5.1NB2TD HZU5.6B2TRF HZS4.7NB2TD ERA34-10TP1 D1NS6 HZS12NB2TD HZT33-02TE D1NL40-TA HZS1ONB2TD EGP10DPKG23 UF4007G23 1SS119-25 RGP10JPKG23 ERB91-02 MTZJ-T-77-18 HSS82 RB441QT-77 —...
  • Page 24: Exploded Views

    REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK X-4037-432-1 BEZEL ASSY A-1294-771-A A MOUNTED PC BOARD 4-042-353-41 EMBLEM (NO. 7), SONY 4-061-573-01 SPRING, TENSION 1-419-092-11 COIL, DEGAUSSING 3-653-339-21 SPRING, COMPRESSION 4-071-152-02 BUTTON, POWER 4-371-521-01 BAND (L), DEGAUSS COIL...
  • Page 25: Packing Materials

    CPD-E210 The components identified with gray shading and a Les composantsidentifies per un trame et une marque critical symbol ( ) are critical for safety. Replace only sont critiques pout le securite. Ne les remplacer que par une piece portant le numero specifie.
  • Page 26: Electrical Parts List

    CPD-E210 SECTION 7 ELECTRICAL PARTS LIST • The components identified by in this Note: manual have been carefully factory-selected for each set in order to satisfy regulations The components identified by shading regarding X-ray radiation. Should and mark are critical for safety. Replace replacement be required, replace only with only with part number specified.
  • Page 27 CPD-E210 Note: Note: The components identified by shading and mark Les composants identifies per un trame et une marque are critical for safety. Replace only with part number sont critiques pour la securite. Ne les remplacer specified. que par une piece portant le numero specifie.
  • Page 28 CPD-E210 Note: Note: The components identified by shading and mark Les composants identifies per un trame et une marque are critical for safety. Replace only with part number sont critiques pour la securite. Ne les remplacer specified. que par une piece portant le numero specifie.
  • Page 29 CPD-E210 Note: Note: The components identified by shading and mark Les composants identifies per un trame et une marque are critical for safety. Replace only with part number sont critiques pour la securite. Ne les remplacer specified. que par une piece portant le numero specifie.
  • Page 30 CPD-E210 Note: Note: The components identified by shading and mark Les composants identifies per un trame et une marque are critical for safety. Replace only with part number sont critiques pour la securite. Ne les remplacer specified. que par une piece portant le numero specifie.
  • Page 31 CPD-E210 Note: Note: The components identified by shading and mark Les composants identifies per un trame et une marque are critical for safety. Replace only with part number sont critiques pour la securite. Ne les remplacer specified. que par une piece portant le numero specifie.
  • Page 32 CPD-E210 Note: Note: The components identified by shading and mark Les composants identifies per un trame et une marque are critical for safety. Replace only with part number sont critiques pour la securite. Ne les remplacer specified. que par une piece portant le numero specifie.
  • Page 33 CPD-E210 Note: Note: The components identified by shading and mark Les composants identifies per un trame et une marque are critical for safety. Replace only with part number sont critiques pour la securite. Ne les remplacer specified. que par une piece portant le numero specifie.
  • Page 34 CPD-E210 Note: Note: The components identified by shading and mark Les composants identifies per un trame et une marque are critical for safety. Replace only with part number sont critiques pour la securite. Ne les remplacer specified. que par une piece portant le numero specifie.
  • Page 35 CPD-E210 Note: Note: The components identified by in this manual have been The components identified by shading carefully factory-selected for each set in order to satisfy and mark are critical for safety. regulations regarding x-ray radiation. Should replacement Replace only with part number specified.
  • Page 36 CPD-E210 Note: Note: The components identified by shading and mark Les composants identifies per un trame et une marque are critical for safety. Replace only with part number sont critiques pour la securite. Ne les remplacer specified. que par une piece portant le numero specifie.
  • Page 37 CPD-E210 NOTES: — 47 — http://cxema.ru...
  • Page 38 CPD-E210 NOTES: — 48 — http://cxema.ru...
  • Page 39 CPD-E210 — 49 — http://cxema.ru...
  • Page 40 CPD-E210 Sony Corporation English Sony Technology Center 99IS74109-1 Product Quality Division Printed in U.S.A. Service Promotion Dept. 9-978-869-01 © 1999.8 — 49 — http://cxema.ru...

Comments to this Manuals

Symbols: 0
Latest comments: