Sony Trinitron CPD-E220 Service Manual

Color computer display
Hide thumbs Also See for Trinitron CPD-E220:

Advertisement

SERVICE MANUAL

CRT
Viewable image size
Resolution
Maximum
Recommended
Standard image area
Deflection frequency*
AC input voltage/current 220 to 240 V, 50/60 Hz, 0.9 A
Power consumption
Dimensions
Mass
Plug and Play
CPD-E220/E215E/E220E
SPECIFICATIONS
0.24 mm aperture grille pitch (center)
17 inches measured diagonally
90-degree deflection
FD Trinitron
Approx. 327 × 243 mm (w/h)
× 9
3
5
(14
/
/
inches)
4
8
16.0" viewing image
Horizontal: 1600 dots (E220/E220E)
1280 dots (E215E)
Vertical: 1200 lines (E220/E220E)
1024 lines (E215E)
Horizontal: 1024 dots
Vertical: 768 lines
Approx. 312 × 234 mm (w/h)
× 9
3
1
(12
/
/
inches)
8
4
Horizontal: 30 to 85 kHz (E220/E220E)
30 to 70 kHz (E215E)
Vertical: 48 to 120 Hz
120 W
Approx. 404 × 413.5 × 419.5 mm (w/h/
d) (16 × 16
× 16
3
5
/
/
inches)
8
8
Approx. 20 kg (44 lb 1 oz)
DDC1/DDC2B/DDC2Bi
TRINITRON
S. Hemisphere Model
N. Hemisphere Model
* Recommended horizontal and vertical timing condition
• Horizontal sync width should be more than 1.0 µsec.
• Horizontal blanking width should be more than 3.0 µsec.
• Vertical blanking width should be more than 500 µsec.
Design and specifications are subject to change without notice.
COLOR COMPUTER DISPLAY
®
[CPD-E220]
Equator Model
Chassis No. SCC-L35B-A
[CPD-E215E]
AEP Model
Chassis No. SCC-L35D-A
[CPD-E220E]
AEP Model
Chassis No. SCC-L35C-A
H1
CHASSIS

Advertisement

Table of Contents
loading

Summary of Contents for Sony Trinitron CPD-E220

  • Page 1: Service Manual

    CPD-E220/E215E/E220E SERVICE MANUAL [CPD-E220] Equator Model S. Hemisphere Model N. Hemisphere Model Chassis No. SCC-L35B-A [CPD-E215E] AEP Model Chassis No. SCC-L35D-A [CPD-E220E] AEP Model Chassis No. SCC-L35C-A CHASSIS SPECIFICATIONS 0.24 mm aperture grille pitch (center) * Recommended horizontal and vertical timing condition •...
  • Page 2 VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR Parts on Set SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS AP- PEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE- MENTS PUBLISHED BY SONY. CIRCUIT ADJUST- MENTS THAT ARE CRITICAL FOR SAFE OPERATION 0.15 µF...
  • Page 3: Power Saving Function

    1 (power) indicator and inform your authorized Sony dealer of the monitor’s condition. Be sure to note the model Press the 1 (power) button twice to turn the monitor name and serial number of your monitor. Also note the make and off and then on.
  • Page 4: Timing Specification

    CPD-E220/E215E/E220E TIMING SPECIFICATION PRIMARY MODE MODE AT PRODUCTION MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6 MODE 7 MODE 8 RESOLUTION 640 X 480 800 X 600 832 X 624 1024 X 768 1024 X 768 720 X 400 640 X 480 1280 X 1024...
  • Page 5: Table Of Contents

    CPD-E220/E215E/E220E TABLE OF CONTENTS Section Title Page 1. GENERAL ..............1-1 2. DISASSEMBLY 2-1. Cabinet Removal ..........2-1 2-2. A and D Boards Removal ........2-1 2-3. Service Position ............ 2-2 2-4. Picture Tube Removal .......... 2-2 2-5. H Board Removal ..........2-3 2-6.
  • Page 6 MENU RESET AC IN MENU RESET...
  • Page 7 AC IN MENU MENU MENU AC IN AC IN...
  • Page 8 MENU MENU MENU MENU MENU MENU MENU MENU 9 3 0 0 K 5 0 0 0 K...
  • Page 11 MENU...
  • Page 12 MENU RESET MENU...
  • Page 13: Disassembly

    CPD-E220/E215E/E220E SECTION 2 DISASSEMBLY 2-1. CABINET REMOVAL Push in the tip of a screwdriver about 10mm to unlock the claw. Cabinet Cabinet Two claws Bezel assembly Bezel assembly Cabinet Two screws (+BVTP 4 x 16) 2-2. A AND D BOARDS REMOVAL A board CN309 CN307...
  • Page 14: Service Position

    CPD-E220/E215E/E220E 2-3. SERVICE POSITION A board 2-4. PICTURE TUBE REMOVAL A board CN307 Tention spring Two screws Degauss coil (+BVTP 4 x 16) Neck assembly Deflection yoke CN602 Chassis assembly Four screws (Hexagon) CN903 Connector (2P) Anode cap (See page 2-3.) Two screws (+BVTT 4 x 8) Two degauss...
  • Page 15: H Board Removal

    CPD-E220/E215E/E220E 2-5. H BOARD REMOVAL Screw (+BVTP 4 x 16) H bracket Claw Picture tube H board Menu button Bezel assembly Cussion • REMOVAL OF ANODE-CAP NOTE: Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon painted on the CRT, after removing the anode.
  • Page 16: Harness Location

    CPD-E220/E215E/E220E 2-6. HARNESS LOCATION Degauss coil H board Picture tube D board CN903 CN505 CN902 CN602 AC inlet CN301 CN304 CN310 CN307 A board...
  • Page 17: Safety Related Adjustment

    CPD-E220/E215E/E220E SECTION 3 SAFETY RELATED ADJUSTMENT When replacing parts shown in the table below, the After adjusting the High Voltage within specification, put the VR cover on VR501 as shown below and apply following operational checks must be performed as a safety precaution against X-ray emissions from the unit.
  • Page 18: Adjustments

    CPD-E220/E215E/E220E SECTION 4 ADJUSTMENTS Connect the communication cable of the connector located on the D board on the monitor. Run the service software and then follow the instructions. 1-690-391-21 A-1500-819-A 3-702-691-01 Interface Unit Connector Attachment IBM AT Computer To BUS CONNECTOR as a Jig D-sub mini Din...
  • Page 19 CPD-E220/E215E/E220E TLV movement 4. Display crosshatch pattern with red and blue lines and black field. 5. Adjust H.STAT and V.STAT with 4 pole magnet. Use 4 pole magnet, not “HSTAT” and “VSTAT”. 4 Pole Magnet 15. If necessary, repeat steps 3-14 to make the optimum condition for the entire screen.
  • Page 20: Diagrams

    SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAMS SIGNAL-IN HD15 PIG-TAIL (VIDEO, RGB OUT) IC001 PRE AMP,OSD MIX IC002 RGB OUT CN301 R.G.B R IN R OUT R VIN2 R VOUT2 GREEN G IN BLUE G OUT G VIN3 G VOUT3 B IN B OUT B VIN1 B VOUT1...
  • Page 21 IC 501 DEFLECTION IC901 CPU CONTROL IC903 RESET T502 Reset CN501 H DRIVE H DRIVE H OUT H DY(+) HDRV Q520,521 Q503 L505 H.DY Q502 H DY(+) H DY(-) BUFF H DRIVE CLBL Q526 IC401 Q523,527 H DY(-) V OUT V DY(-) H SYNC BUFF VOUT1...
  • Page 22: Frame Schematic Diagram

    5-2. FRAME SCHEMATIC DIAGRAM 5-3. CIRCUIT BOARDS LOCATION CN301 VIDEO, RGND RGB OUT GGND VIDEO CABLE GREEN BGND BLUE PICTURE TUBE G1 G2 VIDEO CABLE P701 CN903 MENU MENU ORG LED ORANGE/LED GRN LED GREEN/LED USER CONTROL CN602 µ-COM,DEFLECTION CONTROL, CN501 DEFLECTION,HV,POWER H DY+...
  • Page 23: Schematic Diagrams And Printed Wiring Boards

    5-4. SCHEMATIC DIAGRAMS AND PRINTED (1) Schematic Diagram of H Board • Divided circuit diagram WIRING BOARDS One sheet of D board circuit diagram is divided into four Note: sheets, each having the code D-a to D-d . For example, the •...
  • Page 24: Schematic Diagram Of A Board

    (2) Schematic Diagram of A Board +12V +12VF J001 CRT_SOKET D102 D101 L001 (VIDEO,RGB OUT) 1N4148 1N4148 IC002 CN310 100µH +6.3V BH3863F RGB OUT V901 D202 D201 FB003 IC001 1SS119 1SS119 PICTURE M52743BSP C005 C006 PRE AMP,OSD MIX C013 TUBE D302 D301 R004...
  • Page 25 VIDEO, RGB OUT • A BOARD SEMICONDUCTOR LOCATION — A BOARD (Conductor Side) — — A BOARD (Component Side) — Conductor Component Side Side IC001 IC002 IC003 IC004 TRANSISTOR Conductor Component Side Side Q001 Q002 Q003 Q004 Q005 Q008 Q101 Q201 Q301 DIODE...
  • Page 26 a , b b , c c , d d ) Board (3) Schematic Diagrams of D (a ( µ-COM, DEFLECTION CONTROL) +16V IC901 ST72774 R402 C406 R939 1.82k 0.0033 D402 R403 1N4002 PC0/ 100V 3.3 1/2W PA0/OCMP HSYNCDIV R942 IC903 R940 C404...
  • Page 27 (DEFLECTION) D522 R589 PG104R +12V R586 Q532 Q531 110k R516 2SA733 R523 KSP92 R590 D532 16.4 R537 Z10-160B 4.3k C577 JW(10) 250V 16.4 -27.6 R5111 R408 3.3k R512 1/2W 15.8 R509 R566 3.6k 1/8W Q529 D523 2SC945P 1SS119 V DY+ ABL CONT R5107 Q528...
  • Page 28 (HV) +12V R593 +81V FB502 C564 C598 10.8µH D533 1SS119 R519 T501 IC502 100 2W C537 UC3843A C539 3900p PWM CONT R581 C558 100V 0.033 PICTURE TUBE 100V R5001 D521 COMP VAEF 100 2W R569 BYV27-200 C554 470p 1/2W R554 D516 R584 D515...
  • Page 29 +6.3V Q607 2SA966 D618 C645 L608 S601 +6.3V SW D601 EGP10D POWER D4SB60L-F AC RECT T603 LF601 L606 FB604 D619 T601 CN601 5.2µH 1SS119 C640 F601 2.8µH AC-SOCKET FB612 C632 R601 C602 250V 300µH 250V D622 560k 0.47 D627 D623 FB624 R651 R652...
  • Page 30: D (A, B, C, D) Board

    • D BOARD SEMICONDUCTOR LOCATION µ-COM, DEFLECTION CONTROL, NOTE: D501 The circuit indicated as left contains high voltage of over DEFLECTION, HV, POWER SUPPLY D502 600 Vp-p. Care must be paid to prevent an electric shock in D503 IC401 inspection or repairing. D504 IC501 D505...
  • Page 31: Semiconductors

    5-5. SEMICONDUCTORS BH3863F M52743BSP RN1203 2SC4632LS-CB7 MAA3371X BH3863F-E2 LETTER SIDE TOP VIEW 36 pin DIP ST72774 TOP VIEW 24 pin SOP CATHODE ANODE LA78040 TOP VIEW MTZJ-15A BYV26C 42 pin DIP MTZJ-5.1A MCR100 UF05G MTZJ-5.1B MCR100-8RL TDA4841 RD15ES-B1 CATHODE RD5.1ESB2 1SS119-25 1SS119-25TD TOP VIEW...
  • Page 32: Exploded Views

    CPD-E220/E215E/E220E SECTION 6 EXPLODED VIEWS NOTE: • Items with no part number and no • Items marked " * " are not stocked since ¡ The components identified by mark description are not stocked because they they are seldom required for routine are critical for safety.
  • Page 33: Picture Tube

    4-072-387-01 BUTTON, POWER 1QA70T7C2A 4-060-603-01 SPRING, TENSION 3-653-339-01 SPRING, COMPRESSION 4-072-413-01 BAND, DG COIL DEGAUSS COIL 4-042-353-11 EMBLEM (NO.7), SONY * A-1304-219-A H BOARD, COMPLETE S07C2U0342 4-365-808-01 SCREW (5), TAPPING 4-384-096-01 SCREW (4X16), TAPPING, +P X-4037-104-1 STAND ASSY 0 8-738-558-05 PICTURE TUBE (17TKB)
  • Page 34: Packing Materials

    CPD-E220/E215E/E220E 6-3. PACKING MATERIALS 101 102 ¡ The components identified by mark are critical for safety. Replace only with part number specified. Les composants identifiés par une ¡ marque sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
  • Page 35: Electrical Parts List

    CPD-E220/E215E/E220E CPD-E220/E215E/E220E ¡ The components identified by mark Les composants identifiés par une SECTION 7 ¡ are critical for safety. marque sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce ELECTRICAL PARTS LIST portant le numéro spécifié.
  • Page 36 CPD-E220/E215E/E220E ¡ The components identified by mark Les composants identifiés par une ¡ marque sont critiques pour la sécurité. are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF.NO.
  • Page 37 CPD-E220/E215E/E220E ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la sécurité. (a)(d) Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifié. REF.NO.
  • Page 38 CPD-E220/E215E/E220E ¡ The components identified by mark Les composants identifiés par une ¡ marque sont critiques pour la sécurité. are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF.NO.
  • Page 39 CPD-E220/E215E/E220E ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifié. REF.NO.
  • Page 40 CPD-E220/E215E/E220E ¡ The components identified by mark Les composants identifiés par une ¡ marque sont critiques pour la sécurité. are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF.NO.
  • Page 41 CPD-E220/E215E/E220E ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifié. REF.NO.
  • Page 42 CPD-E220/E215E/E220E ¡ The components identified by mark Les composants identifiés par une ¡ marque sont critiques pour la sécurité. are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF.NO.
  • Page 43 CPD-E220/E215E/E220E ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifié. REF.NO.
  • Page 44 CPD-E220/E215E/E220E Sony Corporation English Computer Display Division Company 2000JL05189-1 Computer Display Div. 9-978-685-01 Printed in Japan  2000.10 – 58 –...

This manual is also suitable for:

Trinitron cpd-e215eTrinitron cpd-e220e

Table of Contents