Juniper T320 Installation Instructions Manual
Internet router and internet routing node control board
Hide thumbs
Also See for T320:
- Hardware manual (306 pages) ,
- Manual (214 pages) ,
- Quick start manual (32 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Manual
T320 Internet Router and T640 Internet
Routing Node Control Board (T-CB)
Installation Instructions
12 November 2004
Part No: 530-012185-01
Revision 2
Contents
This document describes how to remove and replace a Control Board (T-CB) in a
T320 Internet router and a T640 Internet routing node.
T-CB Description . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 2
T-CB Components.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 3
Tools and Parts Required .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 4
Replacing a T-CB .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 4
Removing a T-CB .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 4
Installing a T-CB .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 5
List of Technical Publications . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 6
Requesting Support.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 8
Revision History . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 9
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Juniper T320
Summary of Contents for Juniper T320
-
Page 1: Table Of Contents
Revision 2 This document describes how to remove and replace a Control Board (T-CB) in a T320 Internet router and a T640 Internet routing node. Contents T-CB Description ..............2 T-CB Components.. -
Page 2: T-Cb Description
T320 Internet Router and T640 Internet Routing Node Control Board (T-CB) Installation Instructions T-CB Description Each T-CB works with an adjacent Routing Engine to provide control and monitoring functions for the routing platform (see Figure 1). These functions include determining Routing Engine mastership; controlling power and reset for the other routing platform components;... -
Page 3: T-Cb Components
T-CB Components Each T-CB consists of the following components: 100-MB Ethernet switch. This switch is used for intermodule communication. PCI bus to the Routing Engines. Processor subsystem (SPMB). Three LEDs, located on the T-CB faceplate. These indicate the status of the T-CB. -
Page 4: Tools And Parts Required
T320 Internet Router and T640 Internet Routing Node Control Board (T-CB) Installation Instructions Tools and Parts Required To replace a T-CB, you need the following tools: Phillips (+) screwdriver, number 2 ESD wrist strap with cable Electrostatic bag or antistatic mat... -
Page 5: Installing A T-Cb
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to an approved site ESD grounding point. For more information about ESD, see the T320 Internet Router Hardware Guide or the T640 Internet Routing Node Hardware Guide. -
Page 6: List Of Technical Publications
T320 Internet Router and T640 Internet Routing Node Control Board (T-CB) Installation Instructions If power is applied to the T-CB and its corresponding Routing Engine is functioning normally, the T-CB comes online automatically. To verify that the T-CB is functioning normally, check the LEDs on its faceplate. The green should light steadily a few minutes after the T-CB is installed. - Page 7 JUNOScript API Documentation JUNOScript API Guide Describes how to use the JUNOScript application programming interface (API) to monitor and configure Juniper Networks routers. JUNOScript API Configuration Reference Provides reference pages for the configuration tags in the JUNOScript API.
-
Page 8: Requesting Support
T320 Internet Router and T640 Internet Routing Node Control Board (T-CB) Installation Instructions Book Description JUNOScope Documentation JUNOScope Software User Guide Describes the JUNOScope software graphical user interface (GUI), how to install and administer the software, and how to use the software to manage router configuration files and monitor router operations. -
Page 9: Revision History
Manager, NMC-RX, SDX, Stateful Signature, T320, T640, T-series, and TX Matrix. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners. All specifications are subject to change without notice. Juniper Networks assumes no responsibility for any inaccuracies in this document.
Need help?
Do you have a question about the T320 and is the answer not in the manual?
Questions and answers