Bosch GBH 36 V-LI Compact Professional Original Operating Instructions page 10

OBJ_BUCH-589-001.book Page 10 Monday, December 10, 2007 10:29 AM
10 | English
Battery Charge-control Indication
The three green LEDs of the battery charge-con-
trol indicator 14 indicate the charge condition of
the battery 11. For safety reasons, it is only pos-
sible to check the status of the charge condition
when the machine is at a standstill.
Push button 15 to indicate the charge condition
(also possible when the battery is removed). The
battery charge-control indicator automatically
goes out after approx. 5 seconds.
LED
Continuous lighting 3x green
Continuous lighting 2x green
Continuous lighting 1x green
Flashing light 1x green
When no LED lights up after pushing button 15,
then the battery is defective and must be replaced.
During the charging procedure, the three green
LEDs light up one after the other and briefly go
out. The battery is fully charged when the three
green LEDs light up continuously. The three LEDs
go out again approx. 5 minutes after the battery
has been fully charged.
The battery is equipped with an NTC temperature
control which allows charging only within a tem-
perature range of between 0 °C and 45 °C. A long
battery service life is achieved in this manner.
Auxiliary Handle
Operate your power tool only with the
auxiliary handle 16.
Rotating the Auxiliary Handle (see figure A)
The auxiliary handle 16 can be set to any position
for a secure and low-fatigue working positure.
Turn the wing bolt for adjustment of the auxiliary
handle 10 in counterclockwise direction and set
the auxiliary handle 16 to the required position.
Then tighten the wing bolt 10 again in clockwise
direction.
Adjusting the Drilling Depth (see figure B)
The required drilling depth X can be set with the
depth stop 1.
Press the button for the depth stop adjustment 9
and insert the depth stop into the auxiliary han-
dle 16.
1 619 929 798 | (10.12.07)
The knurled surface of the depth stop 1 must
face downward.
Insert the SDS-plus drilling tool to the stop into
the SDS-plus tool holder 2. Otherwise, the mov-
ability of the SDS-plus drilling tool can lead to
incorrect adjustment of the drilling depth.
Pull out the depth stop until the distance
between the tip of the drill bit and the tip of the
depth stop correspond with the desired drilling
depth X.
Capacity
Selecting Drill Chucks and Tools
≥2/3
For hammer drilling, SDS-plus tools are required
≥1/3
that are inserted in the SDS-plus drill chuck.
<1/3
For drilling without impact in wood, metal, ce-
Reserve ramic and plastic as well as for screwdriving,
tools without SDS-plus are used (e.g., drills with
cylindrical shank). For these tools, a keyless
chuck or a key type drill chuck are required.
Changing the Key Type Drill Chuck
To work with tools without SDS-plus (e.g., drills
with cylindrical shank), a suitable drill chuck
must be mounted (key type drill chuck or keyless
chuck, accessories).
Mounting the Key Type Drill Chuck
(see figure C)
Screw the SDS-plus adapter shank 19 into a key
type drill chuck 18. Secure the key type drill
chuck 18 with the securing screw 17. Please
observe that the securing screw has a left-hand
thread.
Inserting the Key Type Drill Chuck
(see figure D)
Clean the shank end of the adapter shank and
apply a light coat of grease.
Insert the key type drill chuck with the adapter
shank into the tool holder with a turning motion
until it automatically locks.
Check the locking effect by pulling the key type
drill chuck.
Removing the Key Type Drill Chuck
Push the locking sleeve 4 toward the rear and
pull out the key type drill chuck 18.
Bosch Power Tools