Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Table of Contents
Related Manuals for Telkom ADSL 5102G
Summary of Contents for Telkom ADSL 5102G
- Page 1 Telkom ADSL 5102G Router Quick Start Guide...
-
Page 3: Package Content
Telkom ADSL 5102G router 2 X ADSL Micro-filters ü Do not use the Telkom ADSL 5102G in high humidity or high temperature rooms and/or surroundings. I.e. Kitchens. ü Do not open or try to repair the Telkom ADSL 5102G yourself. ü... -
Page 4: The Front Leds
Quick Start Guide The Front LEDs Figure 1 Meaning PWR : Lit when power is ON. SYS : Lit when the router is ready. Lit green when wireless connection is established. WLAN: Flashes when sending/receiving data LAN Port Lit when connected to an Ethernet device. 1-4: Green for 100Mbps;... -
Page 5: The Rear Ports
Telkom ADSL 5102G The Rear Ports Figure 2 Port Meaning Power Switch Power ON/OFF switch Connect the supplied power adapter to this socket. The moment the device is powered on, press it to reset the device or restore to factory default settings. - Page 6 Telkom ADSL 5102G. ü The installation procedure differs for different operating systems. If you are installing the Telkom ADSL 5102G using a Windows XP or Windows 2000 operating system please proceed with the next step below. If you are using a...
- Page 7 ü If nothing happens when you insert the CD, refer to the troubleshooting section at the end of this guide. 1. Please insert the Telkom ADSL 5102G CD now. 2. The installer will now test whether you have the .Net framework installed. If not, you will be prompted to install it.
- Page 8 4. When you have successfully completed the previous step, the wizard will be installed on your hard drive. To run the wizard click on Start> All programs> Telkom ADSL 5102G> Telkom ADSL 5102G Install Wizard. See figure below, and perform the action now.
- Page 9 Telkom ADSL 5102G 5. The easy install wizard will open on your screen. (See figures below) Please note the supplementary information block to the right edge of the form. This block will provide you with relevant information pertaining to the current step and/or specific buttons or actions.
-
Page 10: Hardware Installation
LED’s (front panel lights) are steadily lit. 2. Connect the ADSL line a) Connect one of the included telephone cables between the Telkom wall-socket and one of the sockets on top of the integrated power and surge unit (C). b) Connect the other included telephone cable between the remaining unused socket on top of the integrated power and surge unit and the router’s “LINE”... - Page 11 (F). c) Confirm that the corresponding LAN LED is lit. d) You can connect up to 4 network devices directly to the Telkom ADSL 5102G as shown in the overview sketch (F). 4. Connect the ADSL micro filters a) If you also intend to use traditional telephones (for voice calls) on the ADSL line, you need to connect the included ADSL micro filters.
- Page 12 Quick Start Guide d) Important Note: Make sure that you do not connect any micro filters between the Telkom wall socket used for the router and the router itself. Refer to the overview sketch, from indicator (C) to indicator (D).
-
Page 13: Configuring Pc In Windows 98/Me
Telkom ADSL 5102G Configuring PC in Windows 98/ME 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP/IP -> NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC. - Page 14 Quick Start Guide Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button.
- Page 15 Telkom ADSL 5102G CD. In this section you will: 1) Verify that your computer meets the minimum requirements for Telkom ADSL 2) Test your guest account connection to the www.telkom.co.za website 3) Install (and run) the utility which will setup your own ISP account details on the router 4) Read the router’s manual.
- Page 16 -activate your software firewall after you have completed this step. 5) Click the “Setup your own ISP account” button. The Telkom ADSL 5102G utility will now open. Enter your supplied ISP(Internet Service Provider) username and password in the location indicated by the two arrows in Figure 5.
- Page 17 8) The last button on the menu, “Read 5102G User Manual (.PDF)”, will open the User manual from the CD. It is recommended that you read this manual should you want to make use of some of the advanced features on the Telkom ADSL...
-
Page 18: Getting Started Using A Wireless Connection
ISP (Internet Service Provider) for details. Getting Started using a wireless connection: 1. To ensure wireless security “out-of-the-box”, Telkom distributes each 5102G with a unique WPA pre-shared key already setup on your router. This pre-shared key is printed on a sticker on the back panel of the router. -
Page 19: Troubleshooting
“autorun.exe”. This will start the application from which you may proceed with the installation. Problem Description 3: When I click OK on the Telkom ADSL 5102G utility window (figure 5), it does not seem to respond. (Applicable only to Windows 98, 98SE, ME and NT4) Solution: Please make sure that you have disabled all firewall software on your computer that may block traffic to the router. -
Page 20: Product Support And Contact Information
Quick Start Guide Problem Description 4: When the wizard tries to open the Telkom website or when I try to open any other website, a Dial-up Connection screen pops up asking me to connect to the internet. It doesn’t matter what choice I make I can not connect or see the website.