Subscribe to Our Youtube Channel
Related Manuals for Inverter Fusion PLASMA CUT 40
Summary of Contents for Inverter Fusion PLASMA CUT 40
- Page 1 Instruction Manual PLASMA CUTTER Instruction Manual PLASMA CUT 40 - 1 - USER MANUAL * PLASMA CUT 40...
-
Page 2: Table Of Contents
Torch Connection......................7 TORCH ASSEMBLY ......................7 Torch Assembly Procedure..................7 OPERATION ........................8 To Begin ........................8 Cutting ........................8 Stand-off Cutting ......................8 Piercing........................8 MAINTENANCE ....................... 9 TROUBLESHOOTING……………………………………………………………………….10-11 DIAGRAM.………………………………………………………………………………………...11 WARRANTY…………………………………………………………………………………..12-13 - 2 - USER MANUAL * PLASMA CUT 40... -
Page 3: Guarantee
Maintenance for one year since the date of purchase. INTRODUCTION This manual contains descriptions, operating instructions and basic maintenance procedures for the Plasma Cut 40 machine. A complete understanding of the characteristics and capabilities of this equipment will assure the steady operation for which it was designed. WARNING •... - Page 4 (0) volts before touching any parts. • On inverter power sources, failed parts can explode or cause other parts to explode when power is applied. Always wear a face shield and long sleeves when servicing inverters. - 4 - USER MANUAL * PLASMA CUT 40...
-
Page 5: Plasma
The pressure of this gas flow effectively controls the radius of the plasma beam. NOTE! This machine is designed to use only compressed air as the “gas”. - 5 - USER MANUAL * PLASMA CUT 40... -
Page 6: Voltage Regulation
CUT- 40 Single phase 230V RATE INPUT POWER (KVA) NO -LOAD VOLTAGE (V) RATE OUTPUT CUR (A) RATE OUTPUT VOLTAGE (V) DUTY CYCLE (%) CUT THICKNESS (MM) WEIGHT (KG) DIEMENSIONS (MM) 327*250*155 - 6 - USER MANUAL * PLASMA CUT 40... -
Page 7: Installation
Example: If the machine draws 22 pliers to assure reliable electrical connection. amps @ 220 volts it will draw 44 amps @ 110 volts to produce the same power output. - 7 - USER MANUAL * PLASMA CUT 40... -
Page 8: Operation
You can use this technique when cutting sheet metal to reduce the chance of splatter-back tip damage. - 8 - USER MANUAL * PLASMA CUT 40... -
Page 9: Maintenance
If the Shield Cup does not go on easily, check the threads. 2. Weekly Check for proper fan operation Blow or vacuum dust and dirt out of the entire machine and the air filter. - 9 - USER MANUAL * PLASMA CUT 40... -
Page 10: Troubleshooting
Cutting speed too fast Slow travel speed Torch tilted too much Adjust tilt. Metal too thick Several passes may be necessary Worn torch parts Inspect and repair or replace worn parts - 10 - USER MANUAL * PLASMA CUT 40... -
Page 11: Diagram
100 PSI If you have any problems in setting up or operating, please first consult this manual. If you are still having difficulties after reading this manual, please contact Inverter Fusion Ltd direct. Front View... -
Page 12: Warranty
Subject to the following terms and conditions, Inverter Fusion Limited warrants to the original retail purchaser that new Inverter Fusion Limited equipment sold in the UK is free of defects in material and workmanship at the time of its despatch from Inverter Fusion Limited for the warranty period advertised for the product at the time of sale. - Page 13 Alternatively the warranty may be registered via the company’s website www.inverterfusion.com Warranty Claims Procedure In the event of a claim, the claimant must first contact Inverter Fusion Limited for a warranty claim authorization number. Following this, the Warranty Claim form, as printed on the reverse side of...
Need help?
Do you have a question about the PLASMA CUT 40 and is the answer not in the manual?
Questions and answers