When Check the AC power cord for possible damages. Keep voltage exceeds the specified limits, check each special the part or the lead away from any heat-emitting part. materials. Samsung Electronics...
Page 10
Critical safety parts should be bracketed with ( Use only regular parts for replacements (in particular, flame resistance and dielectric strength specifications). Irregular parts or materials may cause electric shock or fire. Samsung Electronics...
AC source and turn the switch on. Connect the insu- lating resistance meter (500v) to the AC plug blade. The insulating resistance between the blade of the AC plug and that of the conductive material should be more than 1 ㏁. Samsung Electronics...
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Samsung Electronics...
5. Make sure to turn the power off and unplug the power cord from the outlet before repositioning the product. Also check the antenna cable or the external connectors if they are fully unplugged. Damage to the cord may cause fire or electric shock. Samsung Electronics...
2-1 Product Features Block Specfication Major IC Remark POD NIM Tuner Digital/Analog (DTV Built In) S5H2010A01 (Eagle+) PDP Module Samsung SDI V4 Module 50" HD New Module Power Samsung electro mechanics SMPS 50" HD SMPS New SMPS NTSC 3.58, ATSC STP22 (Scaler)
Product Specification 2-2 Key Features Model HP-R5052 48.43 (W) x 32.52 (H) x 3.72 (D) inches (Without Stand) Dimensions Display 48.43 (W) x 34.47 (H) x 13.18 (D) inches (With Stand) 46.8Kg / 103.17 lbs (Without Stand) Weight Display 53.5Kg / 117.95 lbs (With Stand)
Page 17
- You can input the DVI signal using the DVI ↔ HDMI conversion cable. - When connecting HDMI input using the DVI ↔ HDMI conversion cable, connect the sound signal to the DVI Audio IN port using a separate connection cable. Samsung Electronics...
Page 18
35.156 60.317 37.879 IBM PC / AT 800 X 600 70.000 43.75 Compatible 72.188 48.077 75.000 46.875 60.004 48.363 70.069 56.476 1024 X 768 72.000 57.672 75.029 60.023 1280 X 720 59.855 44.772 1360 X 768 60.015 47.712 Samsung Electronics...
ASSY PDP P-ADDRESS E BUFF BOARD BN96-02028A ASSY PDP P-ADDRESS F BUFF BOARD BN96-02029A ASSY PDP P-ADDRESS G BUFF BOARD BN96-02030A ※ When replacing the SMPS or PDP panel, you have to check the voltage printed on the panel sticker and adjust it. Samsung Electronics...
Full Menu Display / Move to Parent Menu Item Selection by Moving the Cursor Direction keys ▲ / ▼ Data Increase/Decrease for the Selected Item Direction keys ◀ / ▶ Source Cycles through the active input source that are connected to the unit Samsung Electronics...
Nim Version T310 MSP Version New_WB_CbCr 3. White Balance Initial Values of Input Modes ITEM Range TV/AV/S-video Component HDMI Sub Bright(SVP) 0~1204 R-Offset 0~1204 G-Offset 0~1204 B-offset 0~1204 Sub Contrast(DNIe) 0~255 R-Gain 0~255 G-Gain 0~255 B-Gain 0~255 Sub Contrast(SVP) Samsung Electronics...
Page 24
07.Analog Y Gain 0~255 08.Analog PB Gain 0~255 09.Analog PR Gain 0~255 10.Black Level Setting 0~255 11.Brightness 0~255 12.UserColor(MAX) 0~127 06.WB Control 01.MP R-Offset2 0~1023 02.MP G-Offset2 0~1023 03.MP B-Offset2 0~1023 04.PP R-Offset2 0~1023 05.PP B-Offset2 0~1023 06.PP B-Offset2 0~1023 Samsung Electronics...
Do not adjust 15000K/-5 Component IN (720p, 60Hz) 10000K/-5 PC Analog IN None Do not adjust 15000K/-5 HDMI IN (720p, 60Hz) 10000K/-5 <Table 2> For PC Mode, perform only calibration and do not perform additional W/B adjustments. Samsung Electronics 3-11...
Page 32
G Cutoff B Cutoff R Gain G Gain Component B gain HDMI R Cutoff G Cutoff B Cutoff R Gain G Gain B gain R Cutoff G Cutoff B Cutoff R Gain G Gain B gain <Table 3> 3-12 Samsung Electronics...
Page 33
* Pattern NO 24 : B&W Lattice Pattern NO 16 : Toshiba ABL Pattern 2. Optical measuring device : CA210 (FL) Please use the MSPG-925 LTH generator for model HP-R5052 3-4-3 Method of Adjustment 1. Adjust the basic level of Component,PC and CVBS input signals.
Page 34
- Adjust Sub-Contrast(DNIe) to set the 'Y' value. - Adjust red gain ('x') and blue gain ('y') to the color coordinates. * Do not adjust the green gain and sub-contrast (Y) data. High light Measurement point Picture 2-4 Toshiba ABL Pattern 3-14 Samsung Electronics...
Page 35
And When you measure High Light, use 70 IRE portion. But if color noise is less in 60 IRE than in 70 IRE, 60 IRE is allowed as a measure point. Picture 2-5 3. Perform adjustments 2-b through 2-d from previous page using the 10 step gray scale pattern. Samsung Electronics 3-15...
(4) Set the bit/second to 115200. (5) Set the data bit to 8 (6) No parity bit. (7) Set stop bit to 1. (8) No flow control. (9) Save in memory. (10) At this point, the new hyper terminal is ready. 3-16 Samsung Electronics...
Page 37
- The version of the program is displayed at the bottom of the Menu screen Main Program Version Boot-code Version 2. Procedures for checking in the Factory Menu When entering Factory Mode, the version of the software is displayed at the bottom of the menu as described on page 3-2. Samsung Electronics 3-17...
1. SMPS Panel voltages must be adjusted after changing SMPS-PCB or PDP module. Range Board Adjustment 190~220V SMPS-MAIN 60~80V Vset 180~210V 80~120V SMPS-DC/DC Vscan -160~210V Voltage SMPS-POD SMPS-MAIN SMPS-DC/DC Label 2. A point of adjusting SMPS-MAIN voltage. TP : Vs (TOP) Va (BOT) Va Adjustment Point Vs Adjustment Point 3-18 Samsung Electronics...
Page 39
Alignment & Adjustment 3. A point of adjusting SMPS-DC/DC. * Use base chassis of PDP panel as GND point. Samsung Electronics 3-19...
- Check to see if the cables are connected according to the connection diagram. 2. Check the power input to the Main Board. 3. Check the voltage in and out between the SMPS ↔ Main Board, between the SMPS ↔ X, Y Drive Board, and between the Logic Boards. Samsung Electronics...
Is the Fuse (F101) of the Main SMPS Replace the Main SMPS Power Input Part blown? Check Main SMPS CN804-2 Pin 3: STB 5V = 5V Replace the Main SMPS Pin 5 PS-ON = 0V Replace the Main Board Samsung Electronics...
Page 46
SMPS, CN of the X Drive Board, and CN of the Y Drive Board, a spark may be generated by the electric charge of the high capacity capacitor. Therefore, wait some time after separating the power cord from the unit. Samsung Electronics...
Page 47
SMPS, CN of the X Drive Board, and CN of the Y Drive Board, a spark may be generated by the electric charge of the high capacity capacitor. Therefore, wait some time after separ ating the power cord from the unit. Samsung Electronics...
Page 48
Board and the speaker replace the cable, if necessary. properly connected? Is the output voltage of SMPS Replace the main SMPS normal? (CN803 #6) Is the speaker output terminal Replace the Main Board of the Main Board normal? Replace the Speaker Samsung Electronics...
Page 49
- Check the tuner output signal (CVBS). - Check the power input of the Main board. Troubleshooting Procedures Is the antenna connection setting Configure properly properly configured? Check CN1001 pin 2 for +33V Replace the Main SMPS Replace the Main Board Samsung Electronics...
No Power, Abnormal screen for each input source, PIP screen trouble,Sound trouble ASSY FUNCTION BN96-02048A Function Key Board The side function key does not work properly ASSY POWER BN96-02050B Power Button Board The remote control does not work properly, the LED does not work properly. Samsung Electronics...
Vs Input Part Vscan Output Rectification Transformer Block (-175~-220) Auxiliary Control Power Feedback Switching Block Block Vset Output Rectification Transformer Block Auxiliary Control Power Feedback Switching Block Block Ve Output Rectification Transformer Block Auxiliary Control Power Feedback Switching Block Block Samsung Electronics...
Page 54
Block Diagram 7-2-3 Module Driver Board Block Diagram 1. Y Main Board Power Input Part Logic Signal Input Part Logic Signal Buffer 2. X Main Board Power Input Part Logic Signal Input Part Logic Signal Buffer Samsung Electronics...
Page 55
CLK A, B 30MHz ADC 1bit CLK A, B BLK, POL, STB BLK, POL, STB 60pin Connector 60pin Connector 7-2-5 Main Board Block Diagram Display Panel 50", 1366 x 768 SVP-EX62 DNIe Lite Audio AMP TAS5122 Optical Out Coaxial Out Samsung Electronics...
Page 57
Pin No Signal Pin No Signal Pin No Signal Pin No Signal Pin No Signal 5.3V 5.3V 1 ■ 1 ■ 1 ■ 1 ■ 1 ■ 5.3V 5.3V Vset 5.3V PS-ON Vscan 5.3V VS-ON STB 5V 5.3V Samsung Electronics...
Page 58
⑥ CN2001(MAIN B'D) CN1004(MAIN B'D) CN1003 (MAIN B'D) 5.3V ↔ SPEAKER ↔ FUNCTION ↔ POWR BUTTON Pin No Signal Pin No Signal Pin No Signal SPK_R+ KEY1 1 ■ 1 ■ 1 ■ SPK_R- KEY2 LED_RED SPK_L+ SPK_L- Samsung Electronics...
Schematic Diagram 10. Schematic Diagram 10-1 POWER & TUNER This Document can not be used without Samsung’s authorization. Power Signal Samsung Electronics 10-1...
Schematic Diagram 10-3 MICOM & IO-EX & AV IN/OUT This Document can not be used without Samsung’s authorization. Power Signal XREF XREF XREF XREF ( I - & Samsung Electronics 10-3...
Schematic Diagram 10-8 POD * This page is not reguired for PODless model. This Document can not be used without Samsung’s authorization. Power Signal 10-8 Samsung Electronics...
Schematic Diagram 10-11 Power & IR A'ssy Board This Document can not be used without Samsung’s authorization. Power Signal 10-11 Samsung Electronics...
Also used to select or adjust items on the Aim the remote control towards this spot on on-screen menu. the TV. 4 CH( ) buttons 8 Speakers Press CH or CH to change channels. Also used to move up or down in the on-screen menu. Samsung Electronics 11-1...
Page 74
Anynet Connect the supplied power cord. Please refer to the Anynet Owner’s Instruction. This jack is for connecting to 2 SERVICE ONLY other Samsung Anynet-enabled devices. Connector for service only. 10 COMPONENT IN 1, 2 3 HDMI/DVI IN Video (Y/P...
Page 75
Press to switch to your favorite channels. 12 CH LIST button Displays the channel list. 13 MODE button Selects a target device to be controlled by the Samsung remote control (i.e., TV, STB, VCR, CABLE, or DVD). 14 PRE-CH button T unes to the previous channel.
Page 76
Press to choose stereo, mono or Separate Audio Program (SAP broadcast). 26 SET button Used during set up of this Samsung remote control, so that it will work compatibly with other devices (VCR, Cable Box and DVD). 27 PIP button Activates picture in picture.
If the ambient brightness is low, it automatically turns the TV brightness down and reduces the power consumption. Super Saving: This mode controls the screen brightness so that the power consumption is always reduced regardless of the ambient brightness. Samsung Electronics 11-5...
Page 78
○ ○ ○ HDMI(D) ○ ○ ○ ○ Note : This TV has only one tuner and does not allow you to watch one TV channel in the main screen and another channel in the PIP screen. 11-6 Samsung Electronics...
11-3-1 Installation Notes 1. Contact a technician for installing the wall bracket. 2. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to perform the wall installation. 3. This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Page 80
4 screws on the wall corresponding hole. bracket to adjust the length. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws . Length between the two locking holes 11-8 Samsung Electronics...
Page 81
). Then place the product ( ) so that it is firmly fixed to the bracket. Make sure to reinsert and tighten the safety pin ( ) to securely hold the product to the bracket. Wall Bracket Wall Samsung Electronics 11-9...
Page 82
Be careful not to get your fingers caught during installation. • Make sure the wall attachment panel brackets are tightened. Otherwise, the TV panel may fall down. • Please secure the mounting bracket on the wall surface after setting its angle at 0°. 11-10 Samsung Electronics...
Page 83
TV before moving it, as the stand may fall and could cause serious injury. Two or more people should carry the TV. Never lay the TV on the floor because of possible damage to the screen. Always store the TV upright. Samsung Electronics 11-11...
: Please lay the PDP unit face down on a soft surface when removing the stand. 12-1-2 Separation of ASSY COVER-STAND CABLE Part Name Description Description Photo Cover ① Remove 6 screws on the SPEAKER-COVER Speaker : BH,+,B,M4,L12,ZPC(BLK) ② Remove the SPEAKER-COVER. Samsung Electronics 12-1...
Page 86
① Remove 24 screws. : BH,+,-,S,M4,L8,ZPC(BLK) ② Remove 4 screws. : M8,L16,ZPC(BLK) ③ Remove the Back Cover. 12-1-5 Separation of ASSY FAN Part Name Description Description Photo ① Remove 3 screws. : PH,+,WWP,M3,L8,NI PLT ② Remove the Fan Assy. 12-2 Samsung Electronics...
Page 87
① Remove 3 screws. : BH,+,-,S,M4,L8,ZPC(BLK) ② Remove 3 screws. : BH,+,B,M4,L8,ZPC(BLK) ③ Remove the sub cover. 12-1-8 Separation of ASSY SPEAKER Part Name Description Description Photo Speaker ① Remove 1 screw. : BH,+,-,S,M4,L8,ZPC(BLK) ② Remove the Speaker Assy. Samsung Electronics 12-3...
Page 88
12-1-10 Separation of ASSY LOGIC BOARD Part Name Description Description Photo Flat Cable ① Take care when separating the Logic Board not to damage the Flat-Cable Connector Cover. Logic Board ① Remove 4 screws. : PH,+,WWP,M3,L8,NI PLT ② Remove the Logic Board. 12-4 Samsung Electronics...
Page 89
① While pressing the connector, apply slight force toward the direction of the cable to release the connector. ① Remove the Flat cable. ① Remove 6 screws. : PH,+,WWP,M3,L8,NI PLT ② Detach all reamining connectors from the X-Drive Board. ③ Remove the X-Drive Board. Samsung Electronics 12-5...
Page 90
Connectors ① Separate the Scan Boards from the Y-Main Board by detaching the 2 connectors and remove the Scan Boards. Y Drive ① Remove 8 screws. : PH,+,WWP,M3,L8,NI PLT ② Detach all connectors from the Y-Main Board and remove the Y-Main Board. 12-6 Samsung Electronics...
Page 91
: PH,+,WWP,M3,L8,NI PLT ② Remove TCP covers. Buffer ① Remove 12 screws. (TOP) : PH,+,WWP,M3,L8,NI PLT ② Remove the E-Board, F-Board and G-Board. Buffer ① Remove 12 screws. (BOT) : PH,+,WWP,M3,L8,NI PLT ② Remove the E-Board, F-Board and G-Board. Samsung Electronics 12-7...
4. If the VS_ON signal from the Logic Board changes from Low to High, the Main SMPS supplies VS power to the X and Y Drive Board through the DC-DC SMPS, and the screen displays a picture on it. Samsung Electronics 13-1...
Page 96
OP001 adjusts the screen brightness according to the sur- rounding brightness when the Power Saving Mode of the User menu is set to Auto. 13-2-4 Function Key Board Function Key. Located on the side of the unit. 13-4 Samsung Electronics...
Page 97
Pin No Signal 5.3V 5.3V 1 ■ 1 ■ 1 ■ FAN-D 1 ■ VT(33V) 5.3V FAN-ON RTN_AMP STB5V RTN_AMP 18V_AMP 5.3V PS-ON 18V_AMP PS-ON VS-ON STB 5V 5.3V ※ CN811, CN806, CN807 and CN808 are not used. Samsung Electronics 13-5...
Page 98
(components, PCB traces,connectors,etc.) under the input conditions specified in Section 3 above. Current Protection as defined below. Output Over Current Limit Unit VS(210V) 20A, Constant Current.(TBD) VA(70V) 10A, Constant Current.(TBD) Output except Vs,Va No damage (Auto Recovery or Shut down.) 13-6 Samsung Electronics...
Page 99
Circuit Description 13-2-6 POD SMPS J0802(POD SMPS) J0802(POD SMPS) ↔ ↔ CN8002(MAIN B'D) CN811(MAIN SMPS) Pin No Signal Pin No Signal 1 ■ +33V 5.3V +12V +12V +6.5V 1. Block Diagram Samsung Electronics 13-7...
Page 100
The circuit that converts the energy transmitted to T801 via the oscillation of the MAIN SWITCHING U802 into DC voltage. The +6.5V and +12V voltages are controlled by the Voltage Regulator and the +30V output voltage is controlled by the Turn Ratio of T801. 13-8 Samsung Electronics...
Page 101
Pin No Signal CN2501(E-Buffer), Pin No Signal 1 ■ 1 ■ CN2701(G-Buffer) 5.3V 1 ■ Pin No Signal 1 ■ Vset 5.3V Vscan 5.3V 5.3V (6) D5.3V, Vg, Ve Test Point (7) Va, Vset, Vscan Test Point Samsung Electronics 13-9...
Page 102
Feedback Switching Block Block DC DC SMPS receives Vs input (195~215V) from the Main SMPS and the necessary Vscan, Vset and Ve voltages are output to operate the PDP Module as shown in the block diagram above. 13-10 Samsung Electronics...
Page 104
ADC 4bit 74MHz DRIVE CONTROL SIGNAL RESET ASIC MICOM nRESET ADC 3bit R,G,B : 16bit R,G,B : 16bit CLK A, B 30MHz ADC 1bit CLK A, B BLK, POL, STB BLK, POL, STB 60pin Connector 60pin Connector 13-12 Samsung Electronics...
Page 105
Outputs data and control signals to the Top right TCP IC. Upper F Buffer board Outputs data and control signals to the top center TCP IC. Upper G Buffer board Outputs data and control signals to the top left TCP IC. Samsung Electronics 13-13...
Page 106
If the measured waveform is different from the following waveforms, the board must be replaced. To check the waveforms, refer to the following waveform patterns. Figure 2. Normal V-SYNC Output Waveform Figure 3. Normal Address Data Output Waveform 13-14 Samsung Electronics...
Page 107
In addition, a weak discharge is introduced, because the applied voltage is low. Samsung Electronics 13-15...
Page 108
Vsc_h : -70V - Scan high bias (Created by the DC-DC power block of the Y Drive board) g) Vdd : 5V - Logic signal buffer IC and IPM h) Vcc : 15V - Gate drive IC ¹× IPM - Logic Signal : Supplied by the Logic board. Gate signal of each switch 13-16 Samsung Electronics...
Page 109
3) Y Buffer Board (Upper, Lower) This board supplies the Scan waveform to the Y port and consists of Upper and Lower boards. For an HD grade unit, 6 scan driver ICs (TEXAS INSTRUMENT SN755867APZP: 64 outputs) are mounted on the board. Samsung Electronics 13-17...
Page 110
By floating the Odd line that caused the Sustain Discharge in the IDS section to the Vscan-h level, and introducing the Sustain Discharge only for Even lines, it compensates for the optical output difference between the Even and Odd lines. 6) CMS Pulse (ComMon Sustain Pulse) Actual optical is output during the common Sustain Discharge section. 13-18 Samsung Electronics...
Page 111
FET2 short circuits, GND is output via the output terminal. 2) When a signal is applied to G1, FET1 short cir cuits and when no signal is applied to G2, FET2 is opened, and 180V is output via the output terminal. Samsung Electronics 13-19...
Page 114
LOW - CN5507 50~41pin - OUTH / 40~17pin - OUTL OUTL OUTH - In addition, the resistance between the points must be higher than a few kΩ . OUTL OUTL OUTH OUTH <Y buffer LOW> <Y buffer U P> 13-22 Samsung Electronics...
Page 115
2) Y Main - Connect the Y Main and Y Buffer, and confirm that the output from TP(CN5410, CN5411) of the Y Buffer UP is the same as #Attachment 1 when the power is supplied. CN5410 CN5411 Samsung Electronics 13-23...
Page 116
Y Main Board <Voltage Adjustment Specifications> Vset Vsc_l Vsc_h 200V 205V -175V -56V 105V ※ The Vsc_h and Vnf voltages are controlled by the DC-DC power part of the Y Main board. DC-DC Vsc_h TP Y Main Board 13-24 Samsung Electronics...
Page 117
Circuit Description 3) X - Check that the output of X-Out of the X board follows the waveform of #Attachment 2 when the power is supplied. XOUT Samsung Electronics 13-25...
Page 118
Circuit Description ※ Attachment 1 ■ Y Output Waveform The Scan Waveform Must Be Observed Y Output Waveform (200us/div, 100V/div) 1us/div, 100V/div (Sustain Waveform) 13-26 Samsung Electronics...
R_ASL_GAIN value by 5 per second according to the changed Lux 9 ~ 22 value. 23 ~ 35 - If more than 3 communication errors or saturation (count1>count0) is Else 128 (default) detected, the default value is set (R_ASL_GAIN=128). 13-28 Samsung Electronics...
Page 121
APC Table can be shifted by adjusting the R_P_Lower_Gain value only. Therefore, the sustain pulse is controllable for the white pattern, even though it was formerly not controllable. Number of Sustain Pulses ※ Caution: The Super Power Saving Mode screen is darker than that of Standard Mode. Samsung Electronics 13-29...
The mirror returns to a blank state so that no stains or after-images are left. The SAMSUNG SKY500N model has both an ANYNET port and a SERVICE jack port. Because the shape of the ANYNET port on the DLP TV is the same as that of the SERVICE jack port of the SKY500N, it fails to turn the TV off after a connection has been reported.
Page 124
Ex: For LCD 15:9 devices, "Wide" is displayed on the OSD instead of "16:9". 4. The picture size can be changed even in the blue screen. However, the picture size should be controlled by the product specifications if the change is impossible due to hardware restrictions. 14-2 Samsung Electronics...
While the aspect ratio of a normal TV is 4:3, that of a wide a single channel only. screen is 16:9. Through a mono interface, it is hard to experience stereophonic sound and the sound is played using only one speaker. Samsung Electronics 14-3...
Page 126
Anynet is an AV network system that enables an easy-to-use camcorder, DTV receiver, DVD, etc. as a video source. AV interface for users by controlling all connected AV devices through the Anynet menu when the AV devices of Samsung Satellite Broadcasting Electronics are connected.
Page 127
Therefore, if someone says that a 5000:1 contrast displays a color by 5000 levels, he is confusing Contrast with Gradation. Brightness Brightness is the brightness per unit screen area, the unit for brightness is candela (cd). For example, 1000cd/m2 means the brightness that is measured when 1000 candles are lit within 1 square meters area. Samsung Electronics 14-5...
Page 128
The Color reproductivity of a TV is a certain % of NTSC. This means the TV displays that particular % of the color coordinate area of the NTSC signal broadcast by the broadcasting station. In general, a CRT TV provides the highest functional color reproductivity. 14-6 Samsung Electronics...