Table of Contents
Advertisement
7 Available signals
The following signals are available for this monitor.
Video signals
Signal format
shown in the
No.
Signal name
status display
(☞ page 7)
1
NTSC
NTSC
2
PAL
PAL
3
B/W50
B/W50
4
B/W60
B/W60
5
480/60i
480/60i
6
576/50i
576/50i
7
480/60p
480/60p
8
576/50p
576/50p
9
640*480/60p
640*480/60p
10
720/60p
720/60p
11
720/50p
720/50p
12
720/30p
720/30p
13
720/25p
720/25p
14
720/24p
720/24p
15
1080/60i
1080/60i
16
1035/60i
1035/60i
17
1080/50i
1080/50i
18
1080/60p
1080/60p
19
1080/50p
1080/50p
20
1080/30p
1080/30p
21
1080/25p
1080/25p
22
1080/24p
1080/24p
23
1080/30psF
1080/60i
24
1080/24psF
1080/24psf
*
1
Analog component signals are compatible with Y on sync signals.
2
*
Compatible with EMBEDDED AUDIO signals
*
3
The signal is recognized as 1080/60i.
Input terminal
COMPO.
E. AUDIO HD/
VIDEO
(Analog
SD SDI
component)*
1
(IN 1, IN 2)*
2
√
—
—
√
—
—
√
—
—
√
—
—
—
√
√
—
√
√
—
√
—
—
√
—
—
—
—
—
√
√
—
√
√
—
√
√
—
√
√
—
√
√
—
√
√
—
√*
3
√
√
√
—
—
—
—
—
—
—
—
√
√
—
√
√
—
√
√
—
√*
3
√*
3
—
√
√
Computer signals (preset)
DVI-D (HDCP) terminals
√: Acceptable
No.
Signal name
—: Not acceptable
1
VGA60
2
WVGA60
DVI-D (HDCP)
3
SVGA60
(Digital component/
digital RGB)
4
XGA60
—
5
WXGA (1280)
—
6
WXGA+60
—
7
SXGA60*
4
—
8
WSXGA+60*
√
4
9
UXGA60*
√
10
WUXGA60*
√
11
720/60p
√
4
12
1080/60p*
√
13
720/50p
√
14
1080/50p*
4
√
*
4
When No. 7–10, 12 and 14 signals come in, thin lines will become obscured because their signal resolution is higher
—
than the screen resolution.
—
• Non-preset signals may not be displayed normally even if their frequency is within the acceptable range (☞
—
"Horizontal/vertical frequency (computer signal)" on page 21).
√
• When a preset signal comes in, the signal format is shown on the status display. For other signals, the
resolution is shown.
√*
3
√
√
Specification of the DVI-D (HDCP) terminal
√
Connect it to the DVI-D output terminal on a personal computer.
√
Pin No.
√
1
√
2
—
3
—
4
5
6
7
8
Attaching the power cord holder
The provided power cord holder prevents accidental
disconnection of the AC power cord from the AC IN terminal.
• The power cord holder consists of two parts, a case and a
cover.
1
AC IN
terminal
Case
Resolution
Horizontal
Vertical
Horizontal (kHz)
640
480
852
480
800
600
1024
768
1280
768
1440
900
1280
1024
4
1680
1050
1600
1200
4
1920
1200
1280
720
1920
1080
1280
720
1920
1080
Input signal
Pin No.
Input signal
T.M.D.S Data 2–
9
T.M.D.S Data 1–
T.M.D.S Data 2+
10
T.M.D.S Data 1+
T.M.D.S Data 2 shield
11
T.M.D.S Data 1 shield
NC
12
NC
NC
13
NC
DDC Clock
14
+5 V Power
DDC Data
15
GND
NC
16
Hot Plug Detect
2
3
Cover
Frequency
Scan system
Vertical (Hz)
31.5
59.9
Non-interlace
31.5
59.9
Non-interlace
37.9
60.3
Non-interlace
48.4
60.0
Non-interlace
47.8
60.0
Non-interlace
55.9
60.0
Non-interlace
64.0
60.0
Non-interlace
65.2
60.0
Non-interlace
75.0
60.0
Non-interlace
74.0
60.0
Non-interlace
45.0
60.0
Non-interlace
67.5
60.0
Non-interlace
37.5
50.0
Non-interlace
56.25
50.0
Non-interlace
Pin No.
Input signal
17
T.M.D.S Data 0–
18
T.M.D.S Data 0+
19
T.M.D.S Data 0 shield
20
NC
21
NC
22
T.M.D.S Clock shield
23
T.M.D.S Clock+
24
T.M.D.S Clock–
CAUTION
• Use only the provided screws.
• Make sure the plug will not be pulled out
after the cover is attached to the case.
To detach the cover
9
Advertisement
Table of Contents
