Table of Contents
Advertisement
7 Rear panel
1
2
The illustration of the monitor is of TM-19L2D.
Note for connections
• Before making any connections, turn off all the
equipment.
• Use a cord whose plugs correctly match the
terminals on this monitor and the equipment.
• Plugs should be firmly inserted; poor connections
could cause noise.
• When unplugging a cord, be sure to grasp its plug
and pull it out.
• DO NOT connect the power cord until all connections
are completed.
• Refer also to the user manual of each piece of
equipment.
7 Available signals
Frequency
Signal type
Horizontal
Vertical (Hz)
(kHz)
NTSC (3.58)
15.734
(60/)59.94
BW/60
15.734
(60/)59.94
PAL
15.625
50
BW/50
15.625
50
480/60i
15.75/15.734
60/59.94
576/50i
15.625
50
√: Acceptable
–: Not acceptable
Input terminal
Status display*
VIDEO 1
VIDEO 2 IN
IN / Y/C
NTSC
√
√
NTSC (Y/C)
BW60
√
√
PAL
√
√
PAL (Y/C)
BW50
√
√
480/60i
–
–
576/50i
–
–
1 AC IN terminal
AC power input connector.
• Connect the provided AC power cord to an
3
AC outlet.
2 Security slot
4
Install a security wire to this slot.
3 SDI IN 1/IN 2/SWITCHED OUT terminals
Input (IN) and output (SWITCHED OUT)
terminals for the SDI signals.
• The SDI signals of the current input (SDI IN
1 or SDI IN 2) are re-clocked, then emitted
from the SWITCHED OUT terminal. (When
VIDEO 1 or VIDEO 2 is selected, the last-
selected SDI signal is emitted.)
• The signals are emitted from the
SWITCHED OUT terminal only when the
5
monitor is on or in the Power Save mode.
• Use the AUDIO INPUT SDI 1 (for SDI IN 1)/
6
SDI 2 (for SDI IN 2) terminal (7) for audio
connection.
7
4 REMOTE terminal (MAKE/TRIGGER)
Terminal for controlling the monitor by an
external control.
☞ "External Control" on page 11
* About the Status Display
When "STATUS DISPLAY" (☞ page 10) is set to "AUTO," the status is displayed for about 3 seconds in
the following cases:
– When you press the INPUT SELECT button of the current input
– When you change the input
SDI 1/SDI 2
– When the signal condition of the current input changes
– When you turn on the monitor
–
• "NO SYNC" is displayed when no video signal comes in.
• "Out of range" is displayed for a noncompliant video signal input.
–
–
–
√
√
5 VIDEO 2 IN/OUT terminals
Input (IN) and output (OUT) terminals for the
composite signals.
• Use the AUDIO INPUT VIDEO 2 terminal
(7) for audio connection.
6 VIDEO 1 IN/OUT, Y/C terminals
Input (IN) and output (OUT) terminals for the
composite signals and input terminal for S-
video signals (Y/C).
• When both the IN and Y/C terminals are
used, signals to the Y/C terminal have
priority.
• Use the AUDIO INPUT VIDEO 1 terminal
(7) for audio connection.
7 AUDIO INPUT VIDEO 1/VIDEO 2/SDI 1/SDI 2
terminals
Input terminals for the analog audio signals.
• Use the video terminal with the same name
for video connection.
Specification of the Y/C terminal
Connect it to the S-video output
terminal.
Pin No.
Input signal
1
GND (Y)
2
GND (C)
3
Y
4
C
ENGLISH
7
Advertisement
Table of Contents
