Table of Contents
Advertisement
Installation
Precautions
• When mounting the Monitor vertically, consult your dealer. (See also page 13).
• When installing the Monitor, be sure to use a dedicated Stand Unit, Wall Mounting Unit, or Monitor Hanger Unit, depending
on a particular case. Ask your dealer for installation.
• When installing the Monitor, refer also to the user manual for each option to use. Do not tilt the Monitor rightward, leftward,
or backward.
• Route the power cord and connection cables along wall or floor corners to avoid walking on them.
• For good heat dissipation, try to leave the following distances of space (minimum) around the Monitor.
• The ambient temperature of the installation place should be within the range of 0˚C to 40˚C.
• When installing the Monitor in a place, such as near the ceiling, the remote control may not work correctly because of possible
effects from the surroundings. If this happens, use the remote control as a wired remote control or move the Monitor where it
is free from these effects.
When installing the Monitor on a stand
Front View
Side View
200
150
150
MENU INPUT
POWER
50
Take measures against the Monitor from overturning:
To protect against abnormal events such as earthquakes and to prevent unexpected accidents, take appropriate measures
for preventing the Monitor from overturning; should it overturn, this could lead to personal injury.
For detailed information, refer to the manual supplied for the stand.
When mounting the Monitor on the wall
Front View
Side View
200
100
100
MENU INPUT
POWER
50
Unit: mm
100
Notes:
• Do not allow the same image (pattern) to be continuously displayed on the screen for a long time; otherwise, the area on the
screen corresponding to the image may vary in brightness, leaving an afterimage on the screen. To reduce the afterimage, you
can use the Refresh function (see page 28).
• The Monitor is manufactured using very high-precision technology, allowing for more than 99.99% active pixels, however, be
aware that only a slight number of pixels may be deficient or lit at all times.
• Do not install the Monitor in such a way that the Monitor and other AV equipment affect each other adversely. (For example,
if a disturbed image or noise due to electromagnetic interference occurs, or if the infrared remote control malfunctions, change
the installation place.)
50
Wall
Unit: mm
When hanging the Monitor from the ceiling
Side View
200
50
Unit: mm
9
Connections
Precautions
• Before making connections, turn off all the equipment.
• Plugs should be firmly inserted; poor connection could cause noise.
• To unplug a cord, be sure to grasp its plug and pull it out.
• Connect the power cord after having finished all other connections.
• Refer also to the user manual of each piece of equipment.
Available Signals
Video signals
The following signals can be input to this Monitor:
• VIDEO A and VIDEO B terminals accept — PAL, PAL60, NTSC, NTSC4.43, and SECAM signals.
• COMPONENT/RGB B terminals accept — 480i, 576i, 480p, 720p, and 1080i (1035i) signals. (You need to set "RGB/COMPO."
to "COMPO." on the menu (see page 23).
(For GM-P420PCE and GM-P421PCE, to input the above signals, you need to install the video input unit (IF-C422P1G), which is
separately purchased.)
Computer signals (Preset)
This Monitor has 13 preset video modes for the most popular industrial standard, and the signals of the following image
resolutions can be input to the RGB input terminals.
Screen resolution
Horizontal
No.
Signal name
Frequency (kHz)
Horizontal
Vertical
1
PC98
640
400
2
VGA400-70
640
400
3
VGA480-60
640
480
4
VGA480-72
640
480
5
VGA480-75
640
480
6
MAC13"
640
480
7
SVGA-56
800
600
8
SVGA-60
800
600
9
SVGA-72
800
600
10
XGA-60
1024
768
11
XGA-70
1024
768
12
RGB15K-60
—
—
13
RGB15K-50
—
—
Notes:
• When a signal other than listed above is input, a part of the screen may become void or an unnecessary picture may appear.
• Signals, though they are within the acceptable range of frequencies, may not be displayed normally, depending on the signal
type.
• Depending on the connected equipment, the Monitor may not be compatible with composite sync (Cs) or G on sync signals.
• When a preset mode signal is input, the vertical frequency displayed on the screen will have an "*" shown at its right top
position.
• When No. 7 to No. 11 signals are input, lines will become thin if their signal frequencies are higher than the screen resolution.
10
Vertical
Scan system
Frequency (Hz)
24.8
56.4
Non-interlace
31.5
70.1
Non-interlace
31.5
59.9
Non-interlace
37.9
72.8
Non-interlace
37.5
75.0
Non-interlace
35.0
66.7
Non-interlace
35.2
56.3
Non-interlace
37.9
60.3
Non-interlace
48.1
72.2
Non-interlace
48.4
60.0
Non-interlace
56.5
70.1
Non-interlace
15.7
59.9
Interlace
15.6
50.0
Interlace
Advertisement
Table of Contents
