Table of Contents
Advertisement
6
RECORDING (contd.)
6-6 Recording with an external activation signal
Recording can be started and stopped externally when an activation signal is input to the rear panel [EXT REC IN] terminal.
1.
CAMERA IN
1
1
2
MONITOR OUT
Signal input/output
terminals
EXT REC
COM
IN
External control device
Control signal of this unit (ground signal)
Start of recording
[EXT MODE] screen
2.
[ E X T MOD E ]
1 . R E C M ODE
2 . H DD F U L L
O U T
[ A L A RM S ENS OR MOD E ]
1 . R E C M OD E
2 . R E C D UR AT ON
I
3 . P R E S E N S OR
R E C
4 . P R E S E N S OR
R E C
D URA T I ON
Select the automatic recording operation.
6-7 Automatic restart of recording after power failure
If a power failure occurs, recording re-starts automatically as soon as the power supply is restored.
To activate this function, set menu switch <POWER ON REC> to "ON". When power is restored after a power outage, recording
starts again in the same mode in use when power was lost.
[ DV R M ODE ]
1 . R E C Q UA L I T Y
2 . R E C S P E ED
R E C T I M E
3 . A UD I O R EC
4 . P OWER O N RE C
5 . S E ARCH B U T T O N
6 .
S K I P
D U
R A
T I O N
7 .
R E P EA T
REC
8 .
T I M E D T
A E R E C
9 .
O PER AT E LO CK MO D E
1 0
. EXT
S W T C HER
I
30
ON
AUDIO
RS-232C
IN
1
CAM SW
ALARM
ALARM
CLOCK
EXT
OUT
IN1
SPARE
RESET
RESET IN
REC IN
2
CLOCK
HDD
COM
SPARE SPARE
COM
RESET OUT
FULL OUT
SIGNAL GND
AUDIO
OUT
HV:5V
LV:OV
Stop
J
OG
T
R I G
OF F
OF F
1 8 0
S EC
OF F
1 0 S EC
J O G
NO RM
3 0
2 7 H
O N
O N
T I
M E
1 HO U R
O F F
O N
Set to "ON".
A L L
O N
Connection
POWER
I
O
OFF
1. Connect an external control device.
AC IN 120 V
50 Hz / 60 Hz
Connect the external control device to the rear panel
[EXT REC IN] and [COM] terminals.
Operation
2. Turn the power ON.
Check the connections and set the [POWER] switch on
the rear panel to ON.
3. Set the menu switches.
Set the required menu switches. For details, refer to
"Setting" on page 18.
[DVR MODE]
[REC QUALITY] : Set the recording picture quality.
[REC SPEED] : Set the recording speed.
[AUDIO REC] : Sets whether or not audio signals
[EXT MODE]
[REC MODE] : Set the recording mode to use when
• When "TRIG" is selected, recording starts when a
signal is input.
To stop recording, press the [STOP] button.
• When "MANUAL" is selected, recording is per-
formed as long as a signal is input.
Reference: "5-3 Menu switch details" on page 19.
4. Engage the Stop mode.
When an activation signal is input to the [EXT REC IN]
terminal, recording starts automatically.
Memo:
● This function is disabled in the Timer Recording
Standby mode.
Caution:
● Because this device automatically performs a system
check when power is restored after a power failure,
there will be a delay before recording re-starts.
are recorded when menu switch
<REC SPEED> is set to a position
other than 1/5 or 1/10.
an activation signal is input.
Advertisement
Table of Contents
