Related Manuals for Long Range Systems T9101
Summary of Contents for Long Range Systems T9101
- Page 1 T9101 & Cancel Panel Paging System Transmitter U S E R M A N U A L Installation, Warranty and Service Information Long Range Systems, Inc. 4550 Excel Parkway, Suite 200 ddison, TX 75001 800.437.4996 www.pager.net •...
-
Page 2: Table Of Contents
Overview of T9101 ........ - Page 3 T9100 Cancel Panel to T9101 ........
-
Page 4: The T9101
Staff Name board, and four mounting bracket kits. Optional Hardware The T9101 and T9100 Cancel Panel have the ability to print a server report to a POS Printer. Contact LRS if you wish to purchase a printer. Hardware Setup Procedure 1. - Page 5 2. Use the #10-32 x 3/8” screws to hold the clamps. Do not fully tighten screws. Clamp Captive Nuts Screws 3. Adjust the distance between clamps until fits to the mounting surface. 4. Tighten screws. Long Range Systems T9101 & Cancel Panel User Manual...
- Page 6 Because the thumbscrews and brackets can be mounted in many ways, they can be adapted to most locations. Thumbscrew Horizontal Mount Mounting Bracket Mounting Screws Vertical Mount Thumbscrew Mounting Bracket Mounting Screws Long Range Systems T9101 & Cancel Panel User Manual...
-
Page 7: Power Connection
1. Plug the power supply into a standard 110V outlet and the barrel connector end into the jack on the side of the transmitter. 2. Upon completion of the setup, make sure pagers are fully charged. Long Range Systems T9101 & Cancel Panel User Manual... -
Page 8: Overview Of T9101
Function Keys Keypad Function Keys The function keys are located along the bottom row of the T9101. - >30 used to page pagers whose number is 31 through 99. - M1 & M2 used to page and program Manager Pagers. -
Page 9: Rest Terminals
The Reset Terminals are located to the user’s left side on the transmitter. These are used to reset a pager for programming. Status LED This LED will light green to indicate that the T9101 is sending information to the pagers or T9100 Cancel Panel. System Specifications Notice: Operation is subject to the following: •... -
Page 10: Using The T9101
To page the managers, press the M1 for the #1 manager pager or M2 for the #2 manager pager. Cancel Page To clear/cancel a pager to the server: • Press CLR – pager #. Long Range Systems T9101 & Cancel Panel User Manual... -
Page 11: User Preferences
User Preferences The T9101 will come with factory settings for normal operating use. Some features can change per the user’s custom needs. Display Current Settings To view the current settings for the transmitter: • Press PROG – PROG – 16. -
Page 12: Display Clock
• If done, press 6 for Yes, if not, press 10 for No. To enable: • Press PROG – PROG – 22. • At [beeper] press 6. • If done, press 6 for Yes, if not, press 10 for No. Long Range Systems T9101 & Cancel Panel User Manual... -
Page 13: Preset Message
• Press 1 for Re-page. • At [time] use the number keys to enter as mm ss (minute, seconds), then press ENT. The screen will briefly show the updated re-page time. Long Range Systems T9101 & Cancel Panel User Manual... -
Page 14: Repeater Delay
The ID of the Restaurant system. Set if more than one LRS system is in an area to prevent interference. To set: • Press PROG – PROG – 14. • At [rest ID], enter a value from 0 to 9, and then press ENT. Long Range Systems T9101 & Cancel Panel User Manual... -
Page 15: Station Id
• If done, press 6 for Yes, if not, press 10 for No. Server Statistics The T9101 can track the daily statistics of the number of times a server was paged, the server’s average re- sponse, and the number of times a manager is paged. - Page 16 Server Stats needs to be turned ON before Stats can be viewed or printed. The transmit- ter must be set as UHF Master. The current POS Printer supported for the T9101 is the Star TSP650. The connection between the transmitter and printer is a “Straight-Through”. This is achieved with a standard DB9 to DB25 adaptor connected to the back of the printer, and on LRS Provided Serial cable to connect the printer to the transmitter.
-
Page 17: Range Test
00:44 Range Test This can be used to determine the effective range of the T9101 in your environment. To start the range test: • Press PROG – PROG – 8. • Select [range] by pressing 10. The Range Test will begin automatically. -
Page 18: Pager Programming
Pager Programming Star and Alpha Pagers can be reprogrammed from the T9101 transmitter. If the pagers need to have their identification code reprogrammed, contact LRS before proceeding. The following is the basic procedure to use: For Server Pagers: 1. Be sure to set the T9101 for the System ID in use. -
Page 19: T9100 Cancel Panel
The row of keys located below the display. These keys will cancel a call to the pager number shown on the display immediately above the respective key. The Cancel Keys also are used during menu selection. Long Range Systems T9101 & Cancel Panel User Manual... -
Page 20: Using The T9100 Cancel Panel
To Cancel a page, press the Cancel Key immediately under the number of the pager. If using a Cancel Panel with T9101, the pager number may be canceled from the Cancel Panel or by press- ing CLR then the pager number on the T9101. -
Page 21: User Preferences
User Preferences The T9100 Cancel Panel operates as a “Slave” to the T9101. Many settings are transmitted to the Cancel Panel via the T9101. To edit preferences, refer to the User Preferences of the T9101. Note: To enter selections greater than 10, the user will need to enter as two numbers. -
Page 22: Ssociating The T9100 Cancel Panel To T9101
3. The transmitter times should synchronize. If a Canel Panel does not synchornize and associate. 1. On T9101, press PROG – PROG – 29 to start Associate mode. NOTE: The T9101 will stay in Asso- ciate for 2 minutes. 2. On Cancel Panel, press PROG – PROG – 2 – 9 – ENT to start Associate mode. When the Cancel Panel associates, it will display : •... -
Page 23: Service Questions And Nswers
SERVICE QUESTIONS AND ANSWERS Should your paging system ever fail or should you need additional paging supplies, call Long Range Systems at (800) 437-4996. Normal Business Hours Monday – Friday 8:30 am to 5:00 pm Central Time. Weekend or Night Emergencies: •... -
Page 24: Lrs P Gers V Il Ble For The T9101
LRS PAGERS AVAILABLE FOR THE T9101 (These pagers are sold separately) SP5 Rechargeable lpha LRS lpha E467 Star Rechargeable Pager USING THE SP5 Select Button www.pager.net Charging Any rechargeable pager will require use of an LRS charger. The SP5 uses the Charger 5 (CH-R5) 1. - Page 25 7. To exit, wait 8 seconds and the pager will go back to the vibe/contrast menu VIBE CONTRAST 8. To exit this menu wait 8 additional seconds Long Range Systems T9101 & Cancel Panel User Manual...
-
Page 26: Settings
4. Press the Select Button to continue scrolling forward through the message or messages Time Pager will display the current time. This feature is automatically updated by the T9101 transmitter. If the time does not appear, a flashing star will appear on the right side of LCD to show pager is operational. -
Page 27: Using The Lrs Lph E467
1. Using the Up (or Down) scroll button scroll until display shows “Power OFF?” 2. Press Read/Select button to set power on/off 3. At “Power OFF?” screen, use Up (or Down) Scroll button to select YES 4. Press Read/Select button to set Long Range Systems T9101 & Cancel Panel User Manual... -
Page 28: Read Message
1. Using the Up (or Down) scroll button scroll until display shows “Set Key Tone” 2. Press Read/Select to set key tone on/off 3. Use the Up (or Down) scroll button to select On or Off 4. Press Read/Select to set Long Range Systems T9101 & Cancel Panel User Manual... -
Page 29: Select Alert
• Select Loud or Soft and press Read/Select to set • Select Duration (seconds) and press Read/Select to set Vibe Off - Use the Up (or Down) scroll button to select • Press Read/Select to set Long Range Systems T9101 & Cancel Panel User Manual... -
Page 30: Using The St R P Ger
• Star pagers are intended to vibrate the number of times determined by the Vibe mode selected. On the T9101 this is done by choosing the V1, V2 or V3 button. This can be a way to send ad- ditional information or to identify 1 of 3 stations. -
Page 31: Cleaning & Charging Instructions For Lrs Paging Equipment
Only 12 VDC power supplies should be used with LRS chargers and transmitters. DC power supplies will cause damage to equipment that is not covered under the standard warranty. Should you have any questions, please contact the LRS Customer Service Department at 800.437.4996. Long Range Systems T9101 & Cancel Panel User Manual... -
Page 32: Warranty
Copyright © 2013, Long Range Systems, Inc. ll Rights Reserved This manual contains proprietary information of Long Range Systems, Inc. (LRS) and is intended for use only by its em- ployees or customers. None of the material contained herein may be copied, reproduced, republished, downloaded, dis- played, posted, or transmitted in any form or by any means, including but not limited to, electronic, mechanical, photocopying, recording, or otherwise without the prior written permission of LRS.