Related Manuals for Long Range Systems LRS Connect TX-7471
Summary of Contents for Long Range Systems LRS Connect TX-7471
- Page 1 LRS Connect Transmitter TX-7471 U S ER MA NUA L Long Range Systems, LLC 1155 Kas Drive, Suite 150 Richardson, TX 75081 800.577.8101 lrsus.com...
-
Page 2: Table Of Contents
Alpha Vibration Level ............21 Long Range Systems... - Page 3 Using the Alphanumeric Coaster Guest Pagers ........46 Long Range Systems...
- Page 4 Terms & Condtions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Long Range Systems...
-
Page 5: Installation And Setup
5. The systems are shipped ready for the most general use. If you need to modify settings, refer to the table of contents to locate a specific function guideline. Connections The following diagram shows the system connections. NETWORK/ETHERNET CABLE 110/220V ELECTRICAL SUPPLY (Optional) 12 VDC POWER ADAPTER ANTENNA KEYPAD/TRANSMITTER Long Range Systems Connect Transmitter User Manual... -
Page 6: Keypad Description
Staff pagers. Clear Key Clears the input when paging a pager and re- turns to the Guest paging display or to restart an input when programming. Long Range Systems LRS Connect Transmitter User Manual... -
Page 7: Initial Power Up And Time Set
2. Press 1) System. 3. Press 2) LRS Connect. 4. Press 3) Status. 5. The screen will now show the current Transmitter Connectivity Status. If the Status is OK, then the link is successful. Long Range Systems Connect Transmitter User Manual... -
Page 8: Changing The Time Of Lrs Connect Uploads
Step 2 - Press in code - 56789 Step 3 - Press 1 System Step 4 - Press F2 (DN) Step 5 - Press 3 API Mode Select 1 for LRSN and 2 for CoAP Long Range Systems LRS Connect Transmitter User Manual... -
Page 9: Basic Paging Operation Guide
5. Press F1 (V1), F2 (V2) or F3 (V3) for 1, 2 or 3 vibrations. All Call Page: Page all guest pagers simultaneously. At (Guest #: - - -) Screen Display: 1. Enter 000 then press ENTER. Long Range Systems Connect Transmitter User Manual... -
Page 10: Page A Cell Phone
Note: These non-editable messages are built into the transmitter. If using Alphanumeric pagers, additional messages can be created (see Create Additional Alphanumeric Messages on pg. 16). See next page for table of canned messages. Long Range Systems Connect Transmitter User Manual... -
Page 11: Canned Message
Officer Station Dock Service Buffet Machine You have mail Seat Diaper change Child crying Operator Table ready Booth To nursery Emergency No special Lobby XX Minutes Hole Help Kitchen Restroom Pro Shop Valet Long Range Systems Connect Transmitter User Manual... -
Page 12: Special Functions
4. Press F1 (YES) to turn theft mode on (Press F2 (NO) to turn off). 5. Main screen display will show “T “ on upper left corner when turned on. Note: Anti-Theft does not work with the RX-SP4. When Anti-Theft is enabled, Repeat Delay is Disabled. Long Range Systems Connect Transmitter User Manual... -
Page 13: Tracking
3. Press F2 (DN) until display shows 1) Tracking. 4. Press 1. 5. Select 2) Duration. 6. Type in a new time, in seconds and press ENTER. Note: Entering 0 will make the Duration run “Forever” Long Range Systems Connect Transmitter User Manual... -
Page 14: Group Paging
• Pagers must be programmed in the group mode. • Staff pagers must be numbered above 100. (1-99 are reserved for groups) • Any alphanumeric pager can be a member of up to 5 groups. Long Range Systems Connect Transmitter User Manual... -
Page 15: Manager Mapping
5. Select contact to program - press 1 (1: Contact #1) or 2 (2: Contact #2). 6. The Screen will show if Contact Sensor is currently on or off: • Press F1 to turn the function ON. • Press F2 to turn the function OFF. Long Range Systems Connect Transmitter User Manual... - Page 16 0-5 Volts DC Contact Diameter 2.5 mm Contact Type Mono Plug LRS Connect Transmitter Dry Contact Cable Specifications: Contact Diameter 2.5 mm Contact Type Mono Plug Number of Conductors Ring Connection Positive Tip Connection Ground Long Range Systems Connect Transmitter User Manual...
-
Page 17: Set Alarms
6. At Set pager Number menu, either: • Enter the number of the pager to be alarmed followed by ENTER. • Press F1 (KEEP) to use the existing number. Note: Entering pager number 911 will page all Alpha pagers. Long Range Systems Connect Transmitter User Manual... -
Page 18: Feature Setup Procedures
1) Flash 30 sec. 2) Flash 5 mins. 3) Beep/Flash. Press F2 (DN). 1) Flash 1 sec. 2) Glow 15 times. 3) Glow 5 mins. Press F2 (DN). 1) Beep 3 times. 2) Beep continuously. Long Range Systems Connect Transmitter User Manual... -
Page 19: Enable Guest Sessions Reporting
Step 1 - Press Setup button Step 2 - Press in code - 56789 Step 3 - Press 1 System Step 4 - Press 3 Guest Sessions Step 5 - Press 1 Enable Long Range Systems Connect Transmitter User Manual... -
Page 20: Set To Page Staff Or Guest Pagers
F3 (EDIT) to change it. Enter the desired message using the number keys, waiting until the cursor moves between letters (i.e. for letter ‘E’ press #2 twice). Similar to a Cell Phone. 6. Press the ENTER key to save your message. Long Range Systems Connect Transmitter User Manual... -
Page 21: Setting System Time/Date For Lrs Connect Transmitter
Note: Asterisk next to an option indicates the current operation mode 24 HOUR TIME 12 HOUR TIME ON DISPLAY ON DISPLAY 13:34 PM 1:34 PM GUEST #: - - - - GUEST #: - - - - Transmitter Screen Long Range Systems Connect Transmitter User Manual... -
Page 22: Repeat Delay
5. Press F2 (DN) until screen displays 3 (Vibe Strength). 6. Press 3 (Vibe Strength). 7. Press F1 (UP) to increase the level or F2 (DN) to lower the level. 8. Press F4 (Done) when finished. Long Range Systems Connect Transmitter User Manual... -
Page 23: Guest Message
7. Press 1 to select Guest or Staff. 8. Press 3) Auto send. 9. Press F1 (Yes) or F4 (No). If Display Prompt is disabled, the message sent will default to the Guest or Staff Message. Long Range Systems Connect Transmitter User Manual... -
Page 24: Using Canned Messages In Staff And Guest Display Prompt
3. Press F2 (DN) until screen shows 1 (POCSAG). 4. Press 1 (POCSAG). 5. Press F2 (DN) until screen shows 1 (Msg Editing). 6. Press 1 (Msg Editing). 7. Select Guest or Staff 8. Press 3) Autosend Long Range Systems Connect Transmitter User Manual... -
Page 25: Staff Message
3. Press F2 (DN) until screen shows 1 (Manager Msg). 4. Press 1 (Manager Msg). 5. Type number 00-99 for selected canned message and press ENTER. Note: See pg. 16 for creating Alpha Messages. Long Range Systems LRS Connect Transmitter User Manual... -
Page 26: Alpha Pager Communication Baud Rate
4. Press F2 (DN) until screen shows 1) POCSAG. 5. Press 1 (1: POCSAG). 6. Press F2 (DN) untill screen shows 1) OTA Baud Rate. 7. Press 1) OTA Baud Rate. 8. Select new Baud Rate. Long Range Systems LRS Connect Transmitter User Manual... -
Page 27: Maintenance Functions
5. Press 3 (3: Station ID). 6. The display shows the current station ID number (default is 1). 7. Press a number to use (0 – 9) to change the default Station ID number and press ENTER. Long Range Systems LRS Connect Transmitter User Manual... -
Page 28: Adjust Transmit Power
7. Press F1 (AM) or F2 (PM). If turning function ON: 8. Enter Start Time for Auto Location (- -: - -) and press ENTER to continue. 9. Press F1 (AM) or F4 (PM). Long Range Systems LRS Connect Transmitter User Manual... -
Page 29: Cell Phone Paging/Messaging
Cell Phone Paging requires broadband internet service, a CAT-5 Ethernet cable, and a contract with Long Range Systems. The bandwidth usage for SMS is about 1.5 kB for each SMS page sent, few hundred bytes for sending pages. The bandwidth usage for cloud reporting is about 0.6 kB for each session uploaded. - Page 30 3. Enter Netmask address for the Connect Transmitter on Network and press ENTER. 4. Enter default gateway address for the Connect Transmitter on Network and press ENTER. 5. Enter DNS address for the Connect Transmitter on Network and press ENTER. Long Range Systems Connect Transmitter User Manual...
-
Page 31: Programming Pagers
This procedure is repeated for each pager being programmed. Two charging bases are suggested for pro- gramming Alpha Coasters. Note: Guest Alpha Pagers numbers must be above POCSAG start. 1. Put all coasters to be programmed on one charger base, leave the second base empty. Long Range Systems Connect Transmitter User Manual... - Page 32 5. Remove the Pager from the charger. 6. At the screen display “Reset Pager. When Pager Stop...” press ENTER. 7. The pager will Vibrate and/or Beep. 8. When the Vibration/Beeping Stops, press ENTER again. Long Range Systems Connect Transmitter User Manual...
-
Page 33: Program Pager Groups
5. At enter Groups, enter the Group Numbers you which to assign the Pager to and press ENTER. 6. Turn Pager or Remove pager from charger. 7. At screen displays “Reset Pagers. When Pagers Stop…” press ENTER. Long Range Systems Connect Transmitter User Manual... -
Page 34: Alpha Encryption
• Follow instructions on display. • Turn the pager off then on . • When it stops vibrating, press ENTER. • Screen will display “Transmitting Key”. • Pager will beep once and display “Pgr Encryption None”. Long Range Systems Connect Transmitter User Manual... -
Page 35: Program Pager Vibration
Note: The welcome message has a 32 character limit. 6. Turn off and then turn on Alpha Pager. 7. Press ENTER. 8. Pager should Beep Once to indicate programming. 9. Cycle power on Pager to view New Message. Long Range Systems Connect Transmitter User Manual... -
Page 36: Wait Reducer
9600 Data bits: Parity: None Stop bits: Flow control: None Screen View of Typing ECHO 9. Type ECHO1 and press ENTER. (This echo function will allow you to see what is being typed.) Long Range Systems Connect Transmitter User Manual... - Page 37 Example: To set an ID of 2, type RID,2 and press ENTER twice. Example Restaurant ID to 2 HyperTerminal Output Showing ID as 2 Type STAT and press ENTER Status View Showing Restaurant ID as 2 Long Range Systems LRS Connect Transmitter User Manual...
- Page 38 Example: To set a Power Setting of 3, type HWPR,3 and press ENTER twice.. Example High Power Set to 1 Hyper Terminal Output Showing High Power Set to 1 Status View Showing High Power Set to 1 Long Range Systems LRS Connect Transmitter User Manual...
- Page 39 The default Baud Rate of Alpha Numeric Pagers is 1200. If the rate on the transmitter is changed, the rate of the Alpha Numeric Pagers will also need to be changed. Example of RF Baud to 2400 Status View Showing RD Baud to 2400 Long Range Systems LRS Connect Transmitter User Manual...
-
Page 40: Repeater Function
• If the periodic TRANSMIT flash does not occur, move the repeater closer to the transmitter and try again. • Keep moving the repeater toward the transmitter until the TRANSMIT flash occurs. • After establishing the correct distance, mount the repeater as high as possible Long Range Systems Connect Transmitter User Manual... -
Page 41: System Specifications
Lifetime of Batteries: Approximately 3-5 years. (depending on usage). Battery Charge Life: Approximately 12 - 48 hours (depending on usage). Recharge Time: Typically 8 hours depending on usage (24 hours minimum from completely “dead”). Long Range Systems LRS Connect Transmitter User Manual... -
Page 42: Battery Powered
If pagers continue to not receive pages, contact LRS. My Cell Phone Paging Is Not Working 1. Do you have an account setup with Long Range Systems for a voice/SMS messaging service? If Yes, proceed to Step 2. 2. Check Network cable and make sure both ends are plugged in. Green Light will be lit, and the Orange Light should blink to indicate connectivity. -
Page 43: Service Questions And Answers
(800) 437-4996 or (214) 553-5308 (24/7 days a week) For weekend or night emergencies: • Long Range Systems has 24/7 live technical support available. • Please keep in mind that options are limited over the weekend. LRS Pagers Available for the... -
Page 44: Using The 4-Line Alphanumeric
1. Using the UP (or DN) scroll button scroll until display shows “Set Contrast”. 2. Press Read/Select. 3. Use the UP (or DN) scroll button to adjust. 4. Press Read/Select to confirm. Long Range Systems LRS Connect Transmitter User Manual... - Page 45 • Set Vibe strength - Strong or Weak and press Read/Select to set. • Set Alert Time (seconds) and press Read/Select to set. Battery The RX-E 4-Line Alphanumeric pager uses 1 AAA Battery. Programming To program the pager see pg. 29 Long Range Systems LRS Connect Transmitter User Manual...
-
Page 46: Using The Star Pager
3. Remove from charger, and pager will vibrate, beep, and light all lights as a verification that it is working. 4. Replace the pager in the charger at the end of each day. Long Range Systems LRS Connect Transmitter User Manual... -
Page 47: Using The Non-Alphanumeric Guest
3. Remove from charger, and pager will vibrate, beep, and light all lights as a verification that it is working. 4. Replace the pager in the charger at the end of each day. • The Alphanumeric Coasters use the Charger 8 (CH-R8). Programming To program the pager see pg. 27 Long Range Systems LRS Connect Transmitter User Manual... -
Page 48: Cleaning & Charging Instructions For Lrs Paging Equipment
LRS Europe GmbH LRS Middle East Ltd LRS South Africa LRS United Kingdom +49 531 310542 0 +9613 81 82 84 +27 21 422 4975 +44(0)1782 537000 www.lrs.eu.com www.lrs-lb.com www.lrssa.com www.lrspagers.co.uk Long Range Systems LRS Connect Transmitter User Manual... -
Page 49: Fcc Statement
20 cm separation from the human body at all times. Afin de se conformer aux exigences d’exposition RF FCC / ISED, cet appareil doit être installé pour fournir au moins 20 cm de séparation du corps humain en tout temps.” Long Range Systems LRS Connect Transmitter User Manual... -
Page 50: Warranty
Warranty Long Range Systems, LLC (LRS) provides a one-year limited warranty on Complete Systems. We warranty your system against defects in materials and workmanship that occur under ordinary use for one year from the original ship date. Warranty does not include damage to the product resulting from accident, natural disasters, misuse, improper electrical connection, or failure to charge the product within 30 days of receipt. -
Page 51: Terms & Condtions
These general terms and conditions (“General Terms and Conditions”) govern all persons (“Purchasers”) that purchase or license equipment, software, firmware, and/or services (collectively “Deliverables”) from Long Range Systems, LLC (“LRS”). Limited Software Use License . All software and firmware (collectively “Software”) is licensed for use only by Purchaser and, in the case of Software for paging receivers, by customers of Purchasers. - Page 52 Purchaser. Neither the customers of Purchaser, nor any other person is an intended beneficiary of these General Terms and Conditions or any agreement that incorporates them, nor shall any such person have Long Range Systems LRS Connect Transmitter User Manual...
- Page 53 General Terms and Conditions impose upon Purchaser shall continue in full force and effect, except any obligation to make payment for a Deliverable prior to its delivery. XU-0156 Rev. B 031220 Long Range Systems LRS Connect Transmitter User Manual...