Related Manuals for Long Range Systems Butler XP
Summary of Contents for Long Range Systems Butler XP
- Page 1 Butler XP P R O G R A M M I N G G U I D E www.pager.net www.pager.net Installation, Warranty and Service Information Long Range Systems, Inc. 4550 Excel Parkway, Suite 200 ddison, TX 75001 800.437.4996 www.pager.net •...
-
Page 2: Table Of Contents
Warranty ..........14 Long Range Systems Butler XP Program Guide... -
Page 3: Launch Butler Xp Pplication
4. Select ll Programs. 5. Select Beach Butler. 6. Select Butler Configurations Utility. 7. The Butler XP configurations screen will display. Manual Install 1. In the event the program does not automatically run on the PC: 2. Insert the CD into the PC drive. -
Page 4: Read Butler
1. Connect one end of the USB cable to the PC. 2. Connect the other end of the USB cable to the Butler XP. The USB connection is located in the Butler XP’s battery compartment. (Batteries are not required for programming). -
Page 5: Configuring A Button Butler
• The Update Butler button must be pressed for changes to be applied. Button Setup The Button section is used to set the message sent to the pager when the “Service” button on the Butler XP is pressed. To set a Message: 1. -
Page 6: Group Paging Enable
This feature will enable or disable the Butler from beeping when the “Service” button is pressed, and when the USB connection is made. To set Beep: Under Beep, click on the Enabled check box to enable or disable (a check mark indicates beep is en- abled). Long Range Systems Butler XP Program Guide... -
Page 7: Secondary Paging
If the page is stopped/canceled after the Secondary Pager goes off, the Secondary Pager will receive “Can- cel isle 15”. This is useful if using more than one pager, so the second person is notified. Long Range Systems Butler XP Program Guide... -
Page 8: Low Battery Page
3. Enter a message. Once set, the function automatically alerts the selected pager when the batter- ies get low. Example: IF: Butler XP with ID of 5 has low batteries THEN: Pager will display “Low Battery 5” Repaging This feature will enable or disable the re-paging feature. When the “Service” button is pressed, the Butler transmitter will resend the message to the pager (at pre-set time intervals) until the page is cleared. -
Page 9: Stop Re-Paging
This feature allows the user to store a read or modified configuration from Button Butlers. File will save to a .b2c extension. To save a Configuration: 1. Select File, Save Configuration. 2. Enter file name, select destination, and Save. Long Range Systems Butler XP Program Guide... -
Page 10: Load An Existing Configuration
3. Press Update Unit (USB cable must be attached to the Button Butler). Programming Pagers Note: Before programming a pager, make sure the pager is turned OFF. The Button Butler does not operate with Star Pagers. Long Range Systems Butler XP Program Guide... -
Page 11: Group
Be sure that pager numbering begins at 100 8. Set the ll Page number. ( ll Page is typically 911) 9. Confirm all settings before continuing. 10. Remove the battery from the pager. Long Range Systems Butler XP Program Guide... -
Page 12: Troubleshooting
1. Plug one end of the USB to the PC and the other end to the Button Butler. 2. Open the Butler Configurations Utility. 3. Click the Read Butler button. 4. The current system ID will be displayed under System ID Long Range Systems Butler XP Program Guide... -
Page 13: Warranty
WARRANTY Long Range Systems Inc warrants this product against any defects that are due to faulty material or work- manship for a two-year period after the original date of consumer purchase. The warranty does not include damage to the product resulting from accident, misuse, improper electrical connection, or failure to charge the product within 30 days of receipt. - Page 14 The user is cautioned to observe a minimum separation distance of at least 20 centimeters (8 inches) from the body of the user or nearby persons while transmitting out the device. XU-0031 042514 Long Range Systems Butler XP Program Guide...