Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Chamberlain CS100EVO
Summary of Contents for Chamberlain CS100EVO
- Page 1 CS100EVO Sectional Garage Door Opener Installation and Operating Instructions Owners Copy: SAVE THESE INSTRUCTIONS for future reference This manual contains IMPORTANT SAFETY information DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY...
-
Page 2: Table Of Contents
400 N (40 kgf). Excessive force will interfere with before installing this opener. the proper operation of the Safety Reverse System or damage SPECIAL NOTE: Chamberlain strongly recommends that the garage door. Do not wear rings, watches or loose clothing while... -
Page 3: Before You Begin
If your door binds, sticks, or is out of balance, call a trained door technician. DOOR TYPES Sectional Door with curved track (MAX. door height 2.2 m) PowerLift Plus - CS100EVO: To suit spring balanced Sectional doors up to 16.0 m Electrical Connection A 240 V General Purpose Outlet (GPO) ie. -
Page 4: Carton Inventory
CARTON INVENTORY Your garage door opener and rail are packed in a single carton. The PowerLift Plus CS100EVO opener cartons contain the opener, the rail, its fitting hardware and accessories. (1) Opener (9) Hardware bag (2) Hand held transmitter x 2... -
Page 5: Tools Required
TOOLS REQUIRED Drill Bits HARDWARE PROVIDED (1) Clevis pin 80 mm (2) R clip (3) Hexagonal head screw (4) Nut M8 3 (4x) 1 (1x) 2 (1x) 4 (4x) (5) Flat washer M8 (6) Clevis Pin 5 (4x) (7) R clip 8 (4x) 7 (1x) 9 (8x) -
Page 6: Control Panel
CONTROL PANEL (located under the cover at the rear of the opener) 1. External Accessory Power: 30 Vdc 50 mA available for universal receiver (not active in Low standby mode). 2. Terminal Block: used for external accessories (see chart below). Function Colour Polarity Comment E-Serial port... -
Page 7: Assembly
ASSEMBLY SECTION ASSEMBLING THE 4 PIECE SEGMENTED RAIL The segmented rail is largely preassembled and consists of 4 parts. The carriage, push rod, release handle, the guide pulley and the lintel bracket with belt tensioner are in the front part (A). The seating for the drive shaft and the sprocket are in the rear part (B). -
Page 8: Installation
INSTALLATION SECTION Wear protective goggles when working overhead to protect your eyes from injury. Disengage all existing garage door locks to avoid damage to the garage door. To avoid serious personal injury from entanglement, remove all ropes connected to the garage door before installing the opener. -
Page 9: Sectional Door
POSITION THE OPENER Disengage the trolley mechanism (see section “Operating the manual release”) and slide it back towards the powerhead. Secure the hanging push arm up into the rail assembly temporarily using tape or rope, to avoid a hazard. SECTIONAL DOOR You will need a 50 mm piece of timber or similar spacer to gauge the distance between door and rail. -
Page 10: Hang The Opener
HANG THE OPENER The opener must be securely fastened to a sound structural support above the opener. fig.1 1.Postion the opener as in the previous step. Check the rail is centred over the door. Ensure the rail brackets (fig.1) is on the Powerhead end of the rail in a position as close to the opener as possible (X). -
Page 11: Operate The Manual Release
Make sure the garage door is fully closed. Pull the manual release ATTACH DOOR ARM TO TROLLEY cord to disengage the trolley. Slide the trolley to around 300 mm Fig. 1 Fig. 2 from the header bracket. 1.The straight door arm is already preassembled to the trolley. 2.Install the curved arm onto the door bracket using the Clevis pin (2) and R-Clip (3) supplied. -
Page 12: Adjustment
ADJUSTMENT SECTION Travel limits regulate the points at which the door will stop PROGRAM THE TRAVEL LIMITS AND FORCE SETTINGS Without a properly installed safety reversal when moving UP or DOWN. The travel limit buttons are located system, persons (particularly small children) under the access cover on the rear panel (figure 1). - Page 13 TEST THE SAFETY REVERSE SYSTEM The safety reverse system test is important. Garage door must reverse on contact with a 40 mm obstacle laid flat on the floor. Failure to properly adjust opener may result in serious personal injury from a closing garage door.
-
Page 14: Install The Protector System (Optional)
System™ no higher than 100 mm above the floor. door is over 400 N (40 kgf). Disconnect power to the garage door opener before installing The Protector System™. SPECIAL NOTE: Chamberlain strongly recommends that The Protector System be installed on all garage door openers. -
Page 15: Timer To Close
TIMER TO CLOSE FEATURE (TTC) Door may operate unexpectedly, therefore do not allow anything to stay in the path of the door. figure 1 The Timer to Close feature requires The Protector System (IR Beams) to be installed. Indicator LED Operation: This feature allows the door to automatically close from a fully open position after a specified time. -
Page 16: Install Warning Labels
INSTALL WARNING LABELS For Service Call RISK OF ENTRAPMENT Installation Date Repeat Safety Reverse Test monthly. Door 114A3361 must reverse on contact with a 40mm obstacle For Service Call placed on the floor. Make necessary adjustments. AUTOMATIC DRIVE: Keep away from the area of the door since it may operate unexpectedly. -
Page 17: Wireless Programming
WIRELESS PROGRAMMING (OPTIONAL ACCESSORIES) Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or remote(s). Do not allow children to play near the door. -
Page 18: Using Your Opener
MAINTENANCE AND CARE OF YOUR OPENER Battery of the remote control: USING YOUR OPENER REPLACE BATTERIES IN REMOTES 1. Your opener can be activated by any of the following devices: • Opener control panel: Up and Down Buttons. The batteries in the remote have an extremely long life. •... -
Page 19: Accessories
ACCESSORIES Model E950C 2 Channel remote control Model E1702M Quick release lock Model E940C 1 Channel visor remote control Model 760AML Outside keyswitch Model 770AML The Protector System E1702M 760AML E950C E940C 770AML... -
Page 20: Troubleshooting
TROUBLE SHOOTING 1. Opener doesn't operate from either door control or 7. Door opens but won't close: remote: • Check The Protector System™ (if you have installed • Does the opener have electric power? Plug lamp into this accessory). If the light on the Beams are flashing, outlet. - Page 21 DIAGNOSTIC CHART Your garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrows on the garage opener flash the diagnostic codes. DIAGNOSTIC CODE SYMPTOM POSSIBLE RESOLUTION UP Arrow DOWN Arrow Flash(es) Flash(es) The garage door opener will not Safety sensors are not installed, connected or wires may be cut.
-
Page 22: Specifications
SPECIFICATIONS - PowerLift Plus - CS100EVO Input Voltage...230-240 Vac, 50 Hz Max. Pull Force ..1000 N Power .....225 Watt Standby Power ..0.8 Watt (door fully closed) Normal Torque ..7 Nm Max door weight..130 kgs Spring balanced Max door area..Sectional door 16 m Motor Type......DC gearmotor permanent lubrication... -
Page 23: Warranty
Unit to you. and support for our goods and are pleased to provide you, the original This Chamberlain Limited Warranty does not cover any failure of, or defect in, purchaser, with this Chamberlain Limited Warranty. - Page 24 Warranty Registration To validate your warranty you must complete the registration form online at: chamberlaindiy.com.au/warranty chamberlaindiy.co.nz/warranty Trademark of The Chamberlain Group, Inc. ® Registered Trademark of The Chamberlain Group, Inc. 114D4627C © 2014, The Chamberlain Group Inc.