Related Manuals for Samsung U32D970
Summary of Contents for Samsung U32D970
- Page 1 UHD Monitor User Manual U32D970 The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. BN46-00430A-01...
-
Page 2: Table Of Contents
Table of contents Before Using the Product Rotating the monitor Connection Using the HDMI Cable Caution Connection Using the DP Cable Copyright Connecting to Headphones or Speakers Connecting the Power Securing the Installation Space Tidying Up the Connected Cables Precautions for storage Using NCE(Natural Color Expert) Connecting the Product to a PC as a Safety Precautions... - Page 3 H-Position & V-Position Configuring PC/AV Mode Configuring H-Position & V-Position Troubleshooting Guide DisplayPort Ver. PIP/PBP Configuring DisplayPort Ver. Requirements Before Contacting Samsung Configuring PIP/PBP Mode Customer Service Center Source Detection Configuring Size Testing the Product Configuring Position Configuring Source Detection...
- Page 4 Table of contents Specifications General PowerSaver Standard Signal Mode Table Appendix Contact SAMSUNG WORLD WIDE Responsibility for the Pay Service(Cost to Customers) Not a product defect A Product damage caused by customer's fault 102 Others Correct Disposal Correct Disposal of This Product (Waste Electrical &...
-
Page 5: Before Using The Product
ⓒ 2014 Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. Microsoft, Windows are registered trademarks of Microsoft Corporation. VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association. -
Page 6: Securing The Installation Space
Warning nearby. A serious or fatal injury may result if instructions are not followed. ― Contact your nearest Samsung Customer Service Center if you want to clean the inside of the product (Service fee will be charged.) Caution Personal injury or damage to properties may result if instructions are not followed. -
Page 7: Cleaning
Cleaning Electricity and Safety ― Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. ― The following images are for reference only. Real-life situations may differ from what is shown in the images. ― Take the following steps when cleaning. ―... -
Page 8: Installation
Install the product at least 10cm away from the wall to allow ventilation. • An increased internal temperature may cause a fire. Only use the power cord provided with your product by Samsung. Do not use the power cord with other products. - Page 9 SAMSUNG • Be sure to consult Samsung Customer Service Center if you want to install the product at such a place.
-
Page 10: Operation
If the product is dropped or the outer case is damaged, turn off the power Do not lift or move the product by pulling the power cord or any cable. switch and disconnect the power cord. Then contact Samsung Customer Service Center. - Page 11 • Your eyesight may deteriorate. when water or other foreign substances have entered the product. Then contact Samsung Customer Service Center. • Product failure, an electric shock or fire may result. Do not hold the product upside-down or move it by holding the stand.
-
Page 12: Correct Posture To Use The Product
Correct posture to use the product Rest your eyes for more than 5 minutes for every 1 hour of product use. • Eye fatigue will be relieved. Do not touch the screen when the product has been turned on for an extended period of time as it will become hot. -
Page 13: Preparations
Chapter 02 Preparations Checking the Components Components - Contact the vendor where you purchased the product if any components are missing. ― Components may vary depending on the country. - The appearance of the components and items sold separately may differ from the image shown. -
Page 14: Parts
Parts Icons Description Open or close the onscreen display (OSD) menu, or return to the parent menu. When the initial screen is displayed, press any button on the front of the product to display the Function Key Guide. With the Guide displayed, press to display the on-screen Front Buttons display menu. - Page 15 Icons Description Turn the screen on or off. The power indicator will be lit when the product is operating normally. ― For details on the power-saving function, refer to “PowerSaver(P.90)” in the product specifications. ― To reduce power consumption, it is best to remove the power cable when not using the product for an extended period of time.
-
Page 16: Reverse Side
Port Description Reverse Side Connect the power cord for your monitor to the POWER IN port on the back of the ― The color and shape of parts may differ from what is shown. Specifications are product. subject to change without notice to improve quality. ―... -
Page 17: Installation
Installation ― The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Caution Take extra care to ensure your hand does not get stuck in the rotating area or the height adjustment area. This could injure your hand. Do not put the hand below the stand body. -
Page 18: Installing A Wall-Mount Kit Or Desktop Stand
Installing a Wall-mount Kit or Desktop Stand ― The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Before Installation ― Power the product off and remove the power cable from the power socket. Place a protective cloth or cushion on a flat surface. - Page 19 The product may get damaged or fall and cause personal injury. Samsung shall not be held liable for any damage or injury caused by using improper screws or attaching the wall-mount kit or desktop stand using excessive force.
-
Page 20: Adjusting The Product Tilt And Height
Adjusting the Product Tilt and Height Rotating the Monitor Screen ― The color and shape of parts may differ from what is shown. Specifications are subject to change You can rotate your monitor as shown below. without notice to improve quality. -1.5˚(-1.5˚,+1.5˚) ~ 91.5˚(-1.5˚,+1.5˚) -30˚(+0,-2˚) ~ 30˚(+2˚,0) -5˚(±2.0˚) ~ 20˚(±2.0˚) -
Page 21: Anti-Theft Lock
Anti-theft Lock ― An anti-theft lock allows you to use the product securely even in public places. ― The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details. To lock an anti-theft locking device: Fix the cable of your anti-theft locking device to a heavy object such as a desk. -
Page 22: Magicrotation Auto
MagicRotation Auto Fourteen languages are available as installation languages. The MagicRotation Auto function detects the rotation of monitors that are fitted with a rotation sensor and rotates the Windows screen accordingly. If the orientation is set to a mode other than "Landscape" in the screen resolution menu on Windows 7, the "MagicRotation Auto"... -
Page 23: Rotating The Monitor Caution
Rotating the monitor Caution If the MagicRotation Auto software is not installed on the monitor, contents on the screen cannot When rotating the monitor, the rotation angle is displayed on the monitor screen. be rotated. The OSD can still rotate by 90° and display properly. Once rotated, the OSD may appear in a different view mode from the mode before it was rotated. -
Page 24: Using Nce(Natural Color Expert)
Chapter 03 Using NCE(Natural Color Expert) Configure the screen settings such as brightness and color tone. What is Monitor Calibration? Most of digital images are managed onscreen. That is why a monitor is very important for photographers and designers. The process to calibrate a monitor in order to display proper colors is called monitor calibration. This product went through a calibration process using color measurement equipment in the factory before shipment. -
Page 25: What Is Nce (Natural Color Expert)
NCE Program Installation/Uninstallation Installation The Natural Color Expert (hereinafter "NCE") program was developed by Samsung Electronics to display optimized colors customized by users. Insert the installation CD into the CD-ROM drive. ― This product supports the monitor calibration feature through the internal NCE function and the provided NCE program. -
Page 26: Starting Nce (Natural Color Expert)
Starting NCE (Natural Color Expert) Connecting the Calibrator Connect the PC IN port on the product to a USB port on the PC using the USB cable. Connect the calibrator to a USB port on the product. ― Install the driver (which is usually provided with a calibration program) provided by the calibrator manufacturer first before connecting the calibrator. The connected calibrator will automatically appear in the Select a Calibrator screen. -
Page 27: Features Of The Nce Program
Features of the NCE Program Select a tab to perform the desired functions. If the Profile List does not contain a profile, select Default and then start calibration. If the Profile List contains profiles, select a profile to edit or calibrate the profile. Layout and Menu Items on the NCE Home Screen Select a profile to preview the screen. -
Page 28: Layout And Menu Items On The Uniformity Screen
Layout and Menu Items on the Uniformity Screen Overview and Functions of the Verification Screen Perform calibration for Uniformity to optimize the display uniformity of the monitor. This screen allows you to verify the difference between the current monitor picture quality and the target value. -
Page 29: Starting Calibration
Starting Calibration Specify the color gamut. If the Profile List does not contain a profile, select Default and then start calibration. If the Profile List contains profiles, select a profile to edit or calibrate the profile. Go to “Home screen – System settings – Profile Mode. ” Basic mode Select Default or a profile from the Profile List. - Page 30 Configure the Black Level setting. If you do not adjust the black level setting by moving the slider Configure the R/G/B Gamma settings. If you configure LUT, the gamma curve of sRGB will be button, the minimum brightness will automatically be applied. applied.
- Page 31 Start calibration. After calibration, you can compare the screens before and after the calibration using the After / Before buttons. • Select the connected calibrator, then click Next. Click Save to save the calibration results to Calibration on the monitor. •...
- Page 32 Advanced Start calibration. • Select the connected calibrator, then click Next. Settings required to calibrate can be configured from a single page. • Attach the calibrator to the indicated spot on the screen, then click Next. ― Set the screensaver time to at least 30 minutes before starting measurement. ―...
- Page 33 After calibration, you can compare the screens before and after the calibration using the After / Before buttons. Click Save to save the calibration results to Calibration on the monitor.
-
Page 34: Connecting And Using A Source Device
Chapter 04 Connecting and Using a Source Device Before Connecting Connecting and Using a PC Check the following before you connect this product with other devices. Select a connection method suitable for your PC. ― Connecting parts may differ in different products. Pre-connection Checkpoints Connection using a Dual-link DVI cable ―... -
Page 35: Connection Using The Hdmi Cable
Connection Using the HDMI Cable Connection Using the DP Cable ― Do not connect the power cable before connecting all other cables. ― Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable. Ensure you connect a source device first before connecting the power cable. -
Page 36: Connecting To Headphones Or Speakers
Connecting to Headphones or Speakers Connecting the Power ― Do not connect the power cable before connecting all other cables. ― Connecting parts may differ in different products. Ensure you connect a source device first before connecting the power cable. The exterior may differ depending on the product. -
Page 37: Tidying Up The Connected Cables
Tidying Up the Connected Cables Remove the COVER-CABLE by sliding it down with both hands Hold the bottom of the stand neck securely with your left in the direction indicated by the arrow. hand and use the thumb of your right hand to slide up the COVER-CABLE to fix it in place. -
Page 38: Connecting The Product To A Pc As A Usb Hub
Connecting the Product to a PC as a USB HUB Connecting a PC to the Product ― The product can function as a HUB by connecting to a PC via a USB cable. You can connect a source device directly to the product and control the device from the product, without having to connect the device to the PC. -
Page 39: Utilizing The Product As A Usb Hub
Utilizing the Product as a USB HUB Using the product as a hub, connect and use various source devices with the product at the same time. A PC cannot connect to multiple source devices at the same time as it has a limited number of input/output ports available. The HUB feature on the product will improve your work efficiency by allowing you to connect multiple source devices to the USB ports on the product at the same time without connecting them to a PC. -
Page 40: Driver Installation
― An installation driver is contained on the CD supplied with the product. Select a language on the product and change the resolution on your PC to the optimum setting. ― If the file provided is faulty, visit the Samsung homepage (http://www.samsung.com/) and download the file. -
Page 41: Screen Setup
Chapter 05 Screen Setup Configure the screen settings such as brightness. A detailed description of each function is provided. Refer to your product for details. Color Mode Configuring Color Mode (with a PC connected) Press any button on the front of the product to display the Function Key Guide. Next, press to display the Mode) suitable for the environment where the Select a color mode... -
Page 42: Configuring Color Mode (With Av Connected)
Configuring Color Mode (with AV connected) Dynamic ― When the external input is connected through DVI/HDMI/DP and PC/AV Mode is set to AV, Color Mode has four automatic Standard picture settings(Dynamic, Standard, Movie, Custom)that are preset at the factory. Movie ―... -
Page 43: Brightness
Brightness Configuring Brightness Press any button on the front of the product to display the Function Key Guide. Next, press to display the You can adjust the general brightness of the picture. (Range: 0~100) corresponding menu screen. A higher value will make the picture appear brighter. ―... -
Page 44: Contrast
Contrast Configuring Contrast Press any button on the front of the product to display the Function Key Guide. Next, press to display the Adjust the contrast between the objects and background. (Range: 0~100) corresponding menu screen. A higher value will increase the contrast to make the object appear clearer. ―... -
Page 45: Sharpness
Sharpness Configuring Sharpness Press any button on the front of the product to display the Function Key Guide. Next, press to display the Make the outline of objects more clear or blurry. (Range: 0~100) corresponding menu screen. A higher value will make the outline of objects clearer. ―... -
Page 46: Color
Color Configuring Color Press any button on the front of the product to display the Function Key Guide. Next, press to display the A detailed description of each function is provided. Refer to your product for corresponding menu screen. details. ―... -
Page 47: Dual Color Mode
Dual Color Mode Configuring Dual Color Mode Press any button on the front of the product to display the Function Key Guide. Next, press to display the Split the screen into two to assign different settings to each of the divided screens. corresponding menu screen. -
Page 48: Response Time
Response Time Configuring the Response Time Press any button on the front of the product to display the Function Key Guide. Next, press to display the Accelerate the panel response rate to make video appear more vivid and natural. corresponding menu screen. ―... -
Page 49: View Calibration Values
View Calibration Values Viewing calibration settings Press any button on the front of the product to display the Function Key Guide. Next, press to display the View calibration settings configured using the Natural Color Expert program. corresponding menu screen. Picture View calibration values Press to move to... -
Page 50: Hdmi Black Level
HDMI Black Level Configuring the HDMI Black Level Settings Press any button on the front of the product to display the Function Key Guide. Next, press to display the If a DVD player or set-top box is connected to the product via HDMI, image quality corresponding menu screen. -
Page 51: Reset Color Mode
Reset Color Mode Configuring Reset Color Mode Press any button on the front of the product to display the Function Key Guide. Next, press to display the Resets your current color mode to its default settings. corresponding menu screen. Picture Reset the current color Press to move to... -
Page 52: Screen Adjustment
Chapter 06 Screen Adjustment Image Size Changing the Image Size Press any button on the front of the product to display the Function Key Guide. Next, press to display the Change the picture size. corresponding menu screen. ― This menu is not available when PIP/PBP Mode is set to and the... - Page 53 mode mode • 4:3: Display the picture with an aspect ratio of 4:3. Suitable for videos and standard broadcasts. Screen Choose the size and • 16:9: Display the picture with an aspect ratio of 16:9. aspect ratio of the Screen Fit: Display the picture with the original aspect ratio without cutting off.
-
Page 54: H-Position & V-Position
H-Position & V-Position Configuring H-Position & V-Position Press any button on the front of the product to display the Function Key Guide. Next, press to display the H-Position: Move the screen to the left or right. corresponding menu screen. V-Position: Move the screen up or down. ―... -
Page 55: Pip/Pbp
PIP/PBP ― The PIP/PBP function may not be available depending on the specifications of the graphics card used. If the screen is blank in PIP/PBP mode when the optimum resolution is selected, go to Control Panel Display Screen Resolution and click Detect on the PC. (Instructions are based on Windows 7.) If the screen is blank when the resolution is set to the optimal resolution, change the resolution as follows: The PIP (Picture in Picture) function separates the screen into two parts. -
Page 56: Configuring Pip/Pbp Mode
Configuring PIP/PBP Mode Enable or disable the PIP/PBP Mode function. Press any button on the front of the product to display the Function Key Guide. Next, press to display the corresponding menu screen. PIP/PBP Turn PIP/PBP Mode on 스크린 or off. PIP/PBP Mode 화면... -
Page 57: Configuring Size
Configuring Size Select the size and aspect ratio of the sub-screen. Press any button on the front of the product to display the Function Key Guide. Next, press to display the corresponding menu screen. PIP/PBP Select the size and 스크린 aspect ratio of the PIP/PBP Mode sub-screen. -
Page 58: Configuring Position
Configuring Position Select the position of the sub-screen from the available options. Press any button on the front of the product to display the Function Key Guide. Next, press to display the ― Not available if Size is set to (PBP mode). -
Page 59: Configuring Sound Source
Configuring Sound Source Set which screen you want to hear the sound for. Press any button on the front of the product to display the Function Key Guide. Next, press to display the corresponding menu screen. PIP/PBP Set which screen you 스크린... - Page 60 (available in PBP mode(Size PIP/PBP Set which screen you 스크린 want to hear the sound PIP/PBP Mode for. 화면 크기 와이드 Size 수평 위치 Position 수직 위치 Sound Source 동시 화면 모드 ▶ Source Image Size Contrast&Color • (available in PBP mode(Size PIP/PBP Set which screen you...
-
Page 61: Configuring Source
Configuring Source Select the source for each screen. Press any button on the front of the product to display the Function Key Guide. Next, press to display the PIP Mode corresponding menu screen. Screen Press to move to and press on the product. - Page 62 PBP Mode Select an input source for the device displayed on each of the divided screens. Press any button on the front of the product to display the Function Key Guide. Next, press to display the (available in PBP mode(Size corresponding menu screen.
- Page 63 (available in PBP mode(Size Select input sources for the devices displayed on the main and sub screens. Press any button on the front of the product to display the Function Key Guide. Next, press to display the Source corresponding menu screen. Screen Press to move to...
-
Page 64: Configuring Image Size
Configuring Image Size Select the image size for sub-screen. Press any button on the front of the product to display the Function Key Guide. Next, press to display the PIP Mode corresponding menu screen. Screen Press to move to and press on the product. - Page 65 PBP Mode Set the Image Size for each of the divided screens. Press any button on the front of the product to display the Function Key Guide. Next, press to display the (available in PBP mode(Size corresponding menu screen. Image Size Screen Press to move to...
-
Page 66: Configuring Contrast&Color
Configuring Contrast&Color Set the Contrast and Color(Red, Green and Blue)for the sub screen. Press any button on the front of the product to display the Function Key Guide. Next, press to display the PIP Mode corresponding menu screen. Screen Press to move to and press on the product. - Page 67 PBP Mode Set the Contrast and Color(Red, Green and Blue)for each screen. Press any button on the front of the product to display the Function Key Guide. Next, press to display the (available in PBP mode(Size corresponding menu screen. Screen Contrast&Color Press to move to...
-
Page 68: Coordinating Osd
Chapter 07 Coordinating OSD A detailed description of each function is provided. Refer to your product for details. Language Configuring Language Press any button on the front of the product to display the Function Key Guide. Next, press to display the Set the menu language. -
Page 69: Display Time
Display Time Configuring Display Time Press any button on the front of the product to display the Function Key Guide. Next, press to display the Set the on-screen display (OSD) menu to automatically disappear if the menu is corresponding menu screen. not used for a specified period of time. -
Page 70: Setup And Reset
Chapter 08 Setup and Reset A detailed description of each function is provided. Refer to your product for details. Eco Saving Configuring Eco Saving Press any button on the front of the product to display the Function Key Guide. Next, press to display the Eco Saving function reduces power consumption by controlling the electric... -
Page 71: Usb Super Charging
USB Super Charging ― Setting USB Super Charging during a data transfer will stop the data transfer. If you set USB Super Charging to Off, the standard charging and data transfer feature will be available. ― High-speed charging is possible using the ports only. -
Page 72: Pc/Av Mode
PC/AV Mode ― Supplied for the wide models only such as 16:9 or 16:10. ― If the monitor (when set to DVI, HDMI, DisplayPort1 or DisplayPort2) is in power saving mode or is displaying the message Check Signal Cable, press the button to display the On Screen Display(OSD). -
Page 73: Displayport Ver
DisplayPort Ver. ― Incorrect settings may cause the screen to go blank. If this occurs, check the device specifications. ― If the monitor (when set to DisplayPort1 or DisplayPort2) is in power saving mode or is displaying the message Check Signal Cable, press the button to display the On Screen Display (OSD). -
Page 74: Source Detection
Source Detection Configuring Source Detection Press any button on the front of the product to display the Function Key Guide. Next, press to display the You can activate Source Detection. corresponding menu screen. ― Not available when PIP/PBP Mode is set to On. Press to move to Settings... -
Page 75: Key Repeat Time
Key Repeat Time Configuring Key Repeat Time Press any button on the front of the product to display the Function Key Guide. Next, press to display the Control the response rate of a button when the button is pressed. corresponding menu screen. Settings Configure the Press... -
Page 76: Off Timer
Off Timer Configuring Off Timer Press any button on the front of the product to display the Function Key Guide. Next, press to display the You can set the product to automatically turn off. corresponding menu screen. Settings Enable or disable the Press to move to Settings... -
Page 77: Configuring Turn Off After
Configuring Turn Off After Off Timer 설정 Set the monitor to automatically turn off Off Timer ― This option is only available when Off Timer is set to On. 에코 세이빙 해제 after a certain time Turn Off After period. PC/AV 모드... -
Page 78: Reset All
Reset All Initializing Settings (Reset All) Press any button on the front of the product to display the Function Key Guide. Next, press to display the Return all the settings for the product to the default factory settings. corresponding menu screen. Settings Return all the settings Press... -
Page 79: Information Menu And Others
Chapter 09 Information Menu and Others A detailed description of each function is provided. Refer to your product for details. Information Picture Screen View the current input source, frequency and resolution. Options Displaying Information Settings Press any button on the front of the product to display the Function Key Guide. Next, press DisplayPort1 HDMI Information... -
Page 80: Configuring Brightness And Contrast In The Initial Screen
Configuring Brightness and Brightness ― This menu is not available when Eco Saving is enabled. Contrast in the Initial Screen Contrast ― This menu is not available when PIP/PBP Mode is set to and the Size is set to (PBP Mode). Adjust the Brightness, Contrast using the... -
Page 81: Installing The Software
Chapter 10 Installing the Software Easy Setting Box Restrictions and Problems with the Installation (Easy Setting Box) The Easy Setting Box installation may be affected by the Graphics Card, Motherboard and the Networking Environment. Easy Setting Box System Requirements Easy Setting Box enables users to use the monitor by partitioning multiple sections. •... -
Page 82: Troubleshooting Guide
Chapter 11 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center Testing the Product Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Check if your product is operating normally by using the product test function. -
Page 83: Check The Following
Check the following. Installation issue (PC mode) Issues Solutions The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connectors are locked. Blank spaces are found on all four sides of the screen when The blank spaces found on the screen have nothing to do with the product. - Page 84 Issues Solutions The screen is not clear. The screen is blurry. Remove any accessories (video extension cable, etc.) and try again. Set the resolution and frequency to the recommended level. The screen appears unstable and shaky. Check that the resolution and frequency for the PC are within the range of resolution and frequency compatible with the product.
- Page 85 Sound issue Issues Solutions There is no sound. Check the connection of the audio cable or adjust the volume. Check the volume. The volume is too low. Adjust the volume. If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound card or software program.
-
Page 86: Q & A
Q & A Question Answer Refer to the user manual for your PC or graphics card for further instructions on adjustment. How can I change the frequency? Set the frequency on your graphics card. • Windows XP: Go to Control Panel Appearance and Themes Display Settings... - Page 87 Question Answer How do I set power-saving mode? • Windows XP: Set power-saving mode in Control Panel Appearance and Themes Display Screen Saver Settings or BIOS SETUP on the PC. • Windows ME/2000: Set power-saving mode in Control Panel Display Screen Saver Settings or BIOS SETUP on the PC.
-
Page 88: Specifications
Chapter 12 Specifications General Size Model Name U32D970 Panel Size 32 Class (31.5 Inches / 80 cm) Display area 697.92 mm (H) x 392.58 mm (V) 27.5 Inches (H) x 15.5 Inches (V) Display area Pixel Pitch 0.18175 mm (H) x 0.18175 mm (V) 0.007156 Inches (H) x 0.007156 Inches (V) - Page 89 ― Color performance specifications represent the typical specifications provided by SEC's measurement device(CA-310) in Factory. : Actual performance may vary either higher or lower. (USA only) Dispose unwanted electronics through an approved recycler. To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect or call, (877) 278 - 0799...
-
Page 90: Powersaver
PowerSaver The power-saving function of this product reduces power consumption by switching off the screen and changing the color of the power LED if the product is not used for a specified period of time. The power is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or move the mouse. Power- saving mode only functions when the product is connected to a PC with a power-saving function. -
Page 91: Standard Signal Mode Table
Standard Signal Mode Table Model Name U32D970 - This product can be set to only one resolution for each screen size to obtain Synchronization Horizontal Frequency 30 ~ 81 kHz the optimum picture quality due to the nature of the panel. Using a resolution... - Page 92 Resolution Horizontal Frequency Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) (kHz) VESA, 800 x 600 37.879 60.317 40.000 - Horizontal Frequency The time required to scan a single line VESA, 800 x 600 48.077 72.188 50.000 from the left to the right side of the screen is called a horizontal cycle.
-
Page 93: Appendix
Chapter 13 Appendix Contact SAMSUNG WORLD WIDE ― If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. NORTH AMERICA U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com/us http://www.samsung.com/ca (English) CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca_fr (French) LATIN AMERICA... - Page 94 LATIN AMERICA http://www.samsung.com/latin (Spanish) COSTA RICA 0-800-507-7267 http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) DOMINICA 1-800-751-2676 http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) ECUADOR 1-800-10-7267 http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) EL SALVADOR 800-6225 http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) GUATEMALA 1-800-299-0013 http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) HONDURAS 800-27919267 http://www.samsung.com/latin_en (English)
- Page 95 062 SAMSUNG (062 726 786) http://www.samsung.com/hr CYPRUS 8009 4000 only from landline http://www.samsung.com/gr 800 - SAMSUNG (800-726786) http://www.samsung.com CZECH Samsung Electronics Czech and Slovak, s.r.o. V Parku 2343/24, 148 00 - Praha 4 DENMARK 70 70 19 70 http://www.samsung.com EIRE 0818 717100 http://www.samsung.com ESTONIA 800-7267 http://www.samsung.com/ee...
- Page 96 0180 6 SAMSUNG bzw. http://www.samsung.com GERMANY 0180 6 7267864* (*0,20 €/Anruf aus dem dt. Festnetz, aus dem Mobilfunk max. 0,60 €/Anruf ) 80111-SAMSUNG (80111 726 7864) only from land line GREECE http://www.samsung.com/gr (+30) 210 6897691 from mobile and land line HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.com/hu...
- Page 97 EUROPE SLOVAKIA 0800 - SAMSUNG (0800-726 786) http://www.samsung.com SPAIN 902172678 http://www.samsung.com SWEDEN 0771 726 7864 (SAMSUNG) http://www.samsung.com http://www.samsung.com/ch (German) SWITZERLAND 0848 - SAMSUNG (7267864, CHF 0.08/min) http://www.samsung.com/ch_fr (French) 0330 SAMSUNG (7267864) http://www.samsung.com ARMENIA 0-800-05-555 http://www.samsung.com AZERBAIJAN 088-55-55-555 http://www.samsung.com BELARUS 810-800-500-55-500 http://www.samsung.com...
- Page 98 1800 266 8282 0800-112-8888 (Toll Free) INDONESIA http://www.samsung.com/id (021) 56997777 JAPAN 0120-327-527 http://www.samsung.com MALAYSIA 1800-88-9999 http://www.samsung.com/my NEW ZEALAND 0800 SAMSUNG (0800 726 786) http://www.samsung.com/nz 1-800-10-7267864 [PLDT] PHILIPPINES 1-800-8-7267864 [Globe landline and Mobile] http://www.samsung.com/ph 02-4222111 [Other landline] SINGAPORE 1800-SAMSUNG (726-7864) http://www.samsung.com/sg TAIWAN 0800-32-9999...
- Page 99 ASIA PACIFIC 0-2689-3232, THAILAND http://www.samsung.com/th 1800-29-3232 VIETNAM 1800 588 889 http://www.samsung.com MENA ALGERIA 0800 100 100 http://www.samsung.com/n_africa http://www.samsung.com/ae (English) BAHRAIN 8000-4726 http://www.samsung.com/ae_ar (Arabic) EGYPT 08000-726786 http://www.samsung.com IRAN 021-8255 http://www.samsung.com 0800-22273 JORDAN http://www.samsung.com/Levant (English) 06 5777444 http://www.samsung.com/ae (English) KUWAIT 183-2255 (183-CALL) http://www.samsung.com/ae_ar (Arabic)
- Page 100 MENA SYRIA 18252273 http://www.samsung.com/Levant (English) TUNISIA 80-1000-12 http://www.samsung.com/n_africa TURKEY 444 77 11 http://www.samsung.com U.A.E 800-SAMSUNG (726-7864) http://www.samsung.com AFRICA BOTSWANA 8007260000 http://www.samsung.com BURUNDI http://www.samsung.com CAMEROON 7095-0077 http://www.samsung.com/africa_fr COTE D’ IVOIRE 8000 0077 http://www.samsung.com/africa_fr 499999 http://www.samsung.com 0800-10077 GHANA http://www.samsung.com/africa_en 0302-200077 KENYA 0800 545 545 http://www.samsung.com...
- Page 101 AFRICA SOUTH AFRICA 0860 SAMSUNG (726 7864) http://www.samsung.com SUDAN 1969 http://www.samsung.com TANZANIA 0685 88 99 00 http://www.samsung.com UGANDA 0800 300 300 http://www.samsung.com ZAMBIA 0211 350370 http://www.samsung.com...
-
Page 102: Responsibility For The Pay Service(Cost To Customers)
― When the service is requested, in spite of in warranty, we may charge you for a visit from a service • Use of supplies or separatly sold product unspecified by Samsung. technician in the following cases. • Repair from a person besides an engineer of outsourcing service company or partner of Samsung Electronics Co., Ltd. Not a product defect •... -
Page 103: Correct Disposal
Correct Disposal Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. -
Page 104: Terminology
Terminology OSD (On Screen Display)____ On Grey scale____ Scale refers to levels Dot Pitch____ The product and screen Vertical Frequency____ One image is Plug & Play____ The Plug & Play screen display (OSD) allows you to of color intensity that show variations consist of red, green and blue dots.